Quoizel MBH8411W Assembly Instruction Sheet

6 CORPORATE PARKWAY
, .
GOOSE CREEK SC 29445
. .
www quoizel com
Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (3) B10 Candelabra Base Bulbs 60W Maximum
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Fixture
A Body
x 1
Tab
B
x 2
Hardware Contents
-
STEP 1 Install Shade
A. Place the Glass Shade (C) into the
Cage (D). Secure by pressing Tabs
(B) onto the Cage (D) and top edge
of the Glass Shade (C).
B. Place the sockets of the Fixture
Body (A) inside of the Glass Shade
(C). Align the label "A" on the bottom
edge of the fixture hood to the label
"A" on the top edge of the Cage (D).
Attach the fixture hood of the Fixture
Body (A) to the top edge of the Cage
(D). Secure them together with Lock
Screws (E). Hand tighten until snug
with screwdrivers.
Figure 1
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2017 QuoizelInc.
Assembly Instruction Sheet #IS-MBH8411W
for product cleaning tips. Go to the
30-45 minutes
Glass Shade
C
x 1
Cage
D
x 1
E
Alternate
Crossbar Mounting
BB
AA Assembly screw
x 1 x 2
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style MBH8411W
Care + Maintenance selection.
-
STEP 2 Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (BB) if your
installation requires a shorter mounting screw.
Lock Screw
Outlet Box
x 3
Mounting Screw
or Alternate Short
Mounting Screw
-
STEP 3 Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (AA).
Place the backplate and Fixture Body (A) onto the Crossbar
Assembly (AA) and secure with mounting balls. Note: The
backplate and Fixture Body (A) should be snug against the wall and
held tight with the mounting balls. If it is not, adjust the length of the
mounting screws or alternate short mounting screws on the
A
Crossbar Assembly (AA) by unscrewing the preassembled hex nut
and lock washer and then screwing the mounting screws or
alternate short mounting screws in or out of the crossbar until the
correct length is achieved. Once the backplate and Fixture Body (A)
Label "A"
is secure, remove the
mounting ball and
Fixture Body (A) and
proceed to Step 4.
B
C
Label "A"
E
D
1of2
.
Supply Wires with
Ground Wire
AA
Outlet Box Screws
(not included)
Figure 2
Mounting Screw
or Alternate Short
Mounting Screw
AA
Hex Nut and
Lock Washer
Figure 3
ReleasedDate:2017-08-02
Backplate
Mounting Ball
A