Linksys WPC4400N Quick Installation page 2

Windows 2000
A
If this screen appears, click
Yes.
B
Locate an available CardBus
slot on your notebook PC.
A
C
With the connector pin end
facing the CardBus slot and
the label facing up, slide the
Adapter into the CardBus slot
until it locks in place.
Then, click Next.
Connecting
the Adapter
D
If this screen appears, click
Yes.
Proceed to Step 3.
D
3
Set up the Adapter
The next screen to appear will be
the Available Wireless Networks
screen. From this screen, you can
launch one of the two setup meth-
ods.
Important: For Quick Installation,
use this document only if your net-
work appears on the Available Wire-
less Networks screen.
Manual Setup: If you are using Man- Available Wireless
ual Setup, click the Manual Setup
Networks
button and follow the on-screen
prompts.
Setting Up the Adapter
with Available Networks
On the Available Wireless Networks
screen, the available networks are
listed in the center table by Avail-
able Wireless Networks. Select the
wireless network you wish to con-
nect to and click the Connect but-
ton. (If you do not see your network
listed, you can click the Refresh but-
ton.)
If the network uses wireless security,
you will need to configure security
on the Adapter. If not, you will be
taken directly to the Congratulations
screen, shown in Step B.
A
If wireless security is enabled
on this network, you will see
one of these wireless security
screens.
WEP Key Needed for
Connection
Select 64-bit or 128-bit. Then,
enter a passphrase or WEP key.
Passphrase - The passphrase
must match the passphrase of
your wireless network.This is
case-sensitive and should not
be longer than 16 alphanumeric
WEP Key Needed
characters.
WEP Key - The WEP key must
match the WEP key of your wire-
less network. For 64-bit encryp- NOTE: Your passphrase must match
tion, enter exactly 10
the passphrase of your other wireless
hexadecimal characters. For
network devices and is compatible
128-bit encryption, enter with Linksys wireless products only.
exactly 26 hexadecimal charac- (Non-Linksys wireless products,
ters. Valid hexadecimal charac-
require a WEP key to be entered.)
ters are "0" to "9" and "A" to "F" .
Click Connect and go to Step B.
WPA-Personal Configuration
Enter the Passphrase. The Pass-
phrase must match the Pass-
phrase of your wireless network
and must be 8-63 characters.
Click Connect and go to Step B.
WPA-Personal
WPA2-Personal Configura-
tion
Enter the Passphrase. The
Passphrase must match the
Passphrase of your wireless
network and must be 8-63
characters.
Click Connect and go to
WPA2-Personal
Step B.
B
After the Adapter is config-
ured for the network, the
Congratulations screen will
appear. Click Finish to com-
plete the setup.
Congratulations!
Setup is complete.
B
NOTE: After the Adapter is
installed, the Wireless Network
Monitor screen will open and its
icon will appear in your PC's system B
For additional information or troubleshooting help,
refer to the User Guide on the Setup CD-ROM. You
tray. Double-click the icon if you
can also call or email for further support.
want to open the Monitor to find
24-hour Technical Support
available wireless networks or for
800-326-7114
configuration changes.
(toll-free from US or Canada)
E-mail Support
support@linksys.com
Website
http://www.linksys.com or
http://support.linksys.com
Wireless Network
RMA (Return Merchandise Authorization)
http://www.linksys.com/support
Monitor icon
FTP Site
ftp://ftp.linksys.com
Sales Information
800-546-5797 (800-LINKSYS)
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S. and
certain other countries. Copyright © 2006 Cisco Sys-
tems, Inc. All rights reserved.
WPC4400N-QI-60615NC BW