Page 3
Owner’s/Operator’s Manual are completed before releasing equipment to the owner. TO THE OWNER: Read this manual before operating your LMC equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all the adjustment and operating procedures before attempting to operate.
Table of Contents Introduction …………………………………………………………………………………………….. 5 Technical Specifications ……………………………………………………………………………….. 5 Safety …………………………………………………………………………………………………… 6 Safety Signal Words ……………………………………………………………………………………. 6 General Safety Guidelines ……………………………………………………………………………… 7 Safety Decal Care ………………………………………………………………………………………. 7 Before Operation ……………………………………………………………………………………….. 8 During Operation ……………………………………………………………………………………….. 9 Highway And Transport Operations …………………………………………………………………… 10-11 Operating Instructions…………………………………………………………………………………...
Introduction Thank you for purchasing your LMC Rotary Tiller. The LMC Rotary Tiller is specifically designed and engi- neered for tractors in the 50-120 horse power range. Technical Specifications Gear drive transmission, 6 Blades per flange, PTO with slip-clutch protection, Solid A-frame, 6” Tilling •...
Important Safety Information Safety It is important that you read the entire manual and to become familiar with this product before you begin using it. This product is designed for certain applications only. The manufacturer cannot be responsible for issues arising from modification.
Important Safety Information General Safety Guidelines Safety of the operator is one of the main concerns in designing and developing a new piece of equipment. De- signers and manufacturers build in as many safety features as possible. However, every year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment.
Important Safety Information How to install Safety Signs: Be sure that the installation area is clean and dry. • Decide on the exact position before you remove the backing paper. • Remove the smallest portion of the split backing paper. •...
Important Safety Information During Operation Children should not be allowed on the product. • Clear the area of small children and bystanders before moving the feeder. • If using a towing unit, securely attach feeder by using a hardened 3/4” pin, a metal retainer, and safety •...
Important Safety Information Highway and Transport Operations Adopt safe driving practices. • Keep the brake pedals latched together at all times. Never use independent braking with machine in tow • as loss of control and/or upset of unit can result. Always drive at a safe speed relative to local conditions and ensure that your speed is low enough for an •...
Page 11
Important Safety Information Highway and Transport Operations Maneuver the tractor or towing vehicle at safe speeds. • Avoid overhead wires or other obstacles. Contact with overhead lines could cause serious injury or • death. Avoid loose fill, rocks and holes, they can be dangerous for equipment operation or movement. •...
Operating Instructions Before attaching the rotary tiller to the tractor, check the unit to ensure there is oil in the top and side gearbox. See Maintenance section for lubricant specifications. Note: Gearboxes are shipped with high performance gear grease, add indicated lubricants to specified lev- els.
Page 13
Operating Instructions Shortening a PTO Driveline 1. With the implement attached to the tractor’s three point hitch, and the PTO driveline not installed, sepa- rate the PTO driveline. Attach the implement end to the implement and the other end to the tractor PTO input shaft.
Page 14
Instructions Operating Working Depth Adjustment The working depth is controlled by raising or lowering the side skids. If the skids are raised, the working depth increases. By lowering the skids, the tilling depth with decrease. Tailgate adjustment Position the tailgate to its desired opening by fitting the bolts into the appropriate holes of the adjustment flange located on the top of the main frame.
Page 15
Operating Instructions Start up After making the necessary adjustments, lower the rotary tiller until the blades are a couple of inches from the ground. Engage the PTO and slowly lower the tiller to begin working. Removal and Storage 1. After finishing, remove the rotary tiller from the tractor. 2.
Operating Instructions • Performing Maintenance Good maintenance is your responsibility. Poor maintenance is an invitation to trouble. • Make sure there is plenty of ventilation. Never operate the engine of the towing vehi- • cle in a closed building. The exhaust fumes may cause asphyxiation. •...
Torque Specifications Notes: This chart is an approximate estimate of torque values. Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for Metric hardware.
Page 19
Rotary Tiller RXT Series Parts Manual Rev. 03/22...
Page 27
Frame RXT-080, RXT-088, RXT-096 (Version 1&2) Item Part # Description Qty. Oil Seal- M53.5 x 76 x 8.5 OS53576085 Rotor Support Shaft - Left side RX0401 Bolt- M12 x 1.75 x 30 BM1217530 Protector- Right Side RX0204 Gasket- Rotor RX0406 RX0201 Side Panel- Right (Version 1) Side Panel- Right (Version 2)
Page 42
Model Modifications - RXT Model Modifications - RXT Model Version Serial Range RXT-072 Up to 151254 RXT-080 Up to 161078 RXT-088 Up to 181098 RXT-096 Up to 171173 RXT-072 151235-151254 RXT-080 161073-161074 RXT-088 181099-181105 RXT-096 171163, 171160, 171161, 171174-171179 RXT-072 151255+ RXT-080 161079 +...
(1) year for non-commercial, state, and municipalities’ use, ninety (90) days for commercial use from date of retail sale. Warranty for rental purposes is thirty (30) days. The obligation of LMC to the purchaser under this warranty is limited to the repair or replacement of defective parts.
Page 44
1715 South Slappey Blvd Albany, GA 31701 800-673-6369 www.lmcag.com...