Page 1
Operating Instructions for Your Cobra 10 Band ™ Extra Sensory Detection ® ® RADAR/LASER DETECTOR 9 2 1 0 M O D E L E S D – K a V Nothing comes close to a Cobra™...
Page 2
• Distinguishes important safety alerts‚ from other K band signals • Mounts easily on windshield or dashboard This booklet describes the simple steps for mounting and setting up your ESD-9210. It also ® Traffic Warning System provides helpful information about how radar and laser guns are used and how you can interpret the alerts you receive.
Local laws information you need to install and operate that contravene this Act, while illegal, may your ESD-9210. If you require further be enforced by your local law enforcement assistance after reading through officials until and unless they are prohibited this manual, Cobra from doing so by federal court action.
You will get optimum performance from Objects that can block or weaken incoming your ESD-9210 if you mount it at a point signals include: approximately in the center of the vehicle, windshield wiper blades...
NOTE: In some vehicles, power is supplied to the cigarette lighter even while the ignition is off. If this is the case with your vehicle, you should turn off or unplug your ESD-9210 when parking for lengthy periods. X K Ka V S...
The factory setting is Highway mode. when the power is turned back on. Highway/City Mode Setting your ESD-9210 to City mode delays all X band audio alerts until the signal strength reaches level 3. (A single beep will sound when the signal is first detected.)
O P E R AT I O N • S E T T I N G S Muting an Alert Auto Mute Mode Your ESD-9210 allows you to quickly turn Auto Mute will automatically reduce the off an audio alert by momentarily pressing audio volume of all alerts after 4 seconds the MUTE button.
™ Setting the SmartMute Activation Point SmartMute™ must be turned on. Your ESD-9210 must be installed in your vehicle. Depending on whether the unit is in Tone Caution: Do not attempt to set the rev Alert or Voice Alert™ mode, you will hear point while driving.
O P E R AT I O N • S E T T I N G S Voice/Tone Setting You can set your ESD-9210 to sound alerts with either a voice or a tone. You change settings by using the MUTE button.
Signals Detected The tables on the following pages show the strength of the signal detected. you the types of signals your ESD-9210 (1 = weakest, 5 = strongest) will detect, as well as the voice and visual alerts it provides for each one.
X K Ka Visual Display is a registered trademark of TOMAR Instant-On Detection You should take appropriate Your ESD-9210 is designed to detect action immediately whenever instant-on speed monitoring signals, which an alert is given. can suddenly appear at full strength.
K band radar. Your K band 24.150 GHz ESD-9210, however, is designed to Ka band 33.400-36.00 GHz differentiate between standard K band Your ESD-9210 detects signals in all three and Safety Alert radar bands. alerts for each. VG-2 Safety Alert VG-2 is a "detector detector"...
Maintenance of Your Service Radar Detector You can receive technical assistance with Your ESD-9210 is designed and built to your unit through one of our customer give you years of trouble-free performance support services: without the need for service. No routine Automated Help Desk is available maintenance is required.
3"W x 1 ⁄ "H x 4 ⁄ "D Weight 140 grams This radar detector is covered by one or more of the following U.S. patents: 5,497,148; 5,594,432; 5,612,685; 6,078,279; 6,094,148. Additional patents may be listed inside the product or pending.
For credit card orders fill out order Make check or money order form and fax to: 773.622.2269 payable to: or call 773.889.3087 Cobra Electronics (Press 1 from the main menu) 6500 West Cortland Street 8:00 am - 6:00 pm, M-F, CST. Chicago, IL 60707 USA Attn: Accessories Dept.
Need help?
Do you have a question about the ESD-9210 and is the answer not in the manual?
Questions and answers