REMKO ETR 1-10 Operating And Installation Instructions

REMKO ETR 1-10 Operating And Installation Instructions

Electronic moisture-proof thermostats

Advertisement

Quick Links

Operating and
installation instructions
REMKO thermostats
Electronic moisture-proof thermostat
ERT 1-10
0265-2020-05 Edition 1, en_GB
Read the instructions prior to performing any task!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ETR 1-10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for REMKO ETR 1-10

  • Page 1 Operating and installation instructions REMKO thermostats Electronic moisture-proof thermostat ERT 1-10 0265-2020-05 Edition 1, en_GB Read the instructions prior to performing any task!
  • Page 2 Read these operating instructions carefully before commis- sioning / using this device! These instructions are an integral part of the system and must always be kept near or on the device. Subject to modifications; No liability accepted for errors or mis- prints! Translation of the original...
  • Page 3: Table Of Contents

    Table of contents Safety and usage instructions......................4 1.1 General safety notes........................4 1.2 Identification of notes........................4 1.3 Personnel qualifications........................4 1.4 Dangers of failure to observe the safety notes................4 1.5 Safety-conscious working....................... 4 1.6 Safety notes for the operator......................5 1.7 Safety notes for installation, maintenance and inspection..............
  • Page 4: Safety And Usage Instructions

    REMKO thermostats Safety and usage instructions CAUTION! This combination of symbol and signal word 1.1 General safety notes warns of a potentially hazardous situation, which if not avoided may cause injury or mate- Carefully read the operating manual before com- rial and environmental damage.
  • Page 5: Safety Notes For The Operator

    "certificate of warranty" to The units and components should not be oper- REMKO GmbH & Co. KG at the time when the ated in areas where there is a heightened risk units are purchased and commissioned.
  • Page 6: Transport And Packaging

    REMKO thermostats The warranty conditions are detailed in the "Gen- eral business and delivery conditions". Further- more, only the parties to a contract can conclude special agreements beyond these conditions. In this case, contact your contractual partner in the first instance.
  • Page 7: Technical Data

    Technical data 2.1 Unit data Series ETR 1-10 Temperature measurement range °C -15 to +99 Switching difference (∆ 1 to 10 Temperature probe PT1000 resistance thermometer (no polarity) Operating voltage V/Ph/Hz 230V/1~/50Hz Permissible ambient temperature °C -10 to +65 Storage temperature °C...
  • Page 8: Unit Dimensions

    REMKO thermostats 2.2 Unit dimensions 1 25 20,1 28,4 1 7,5 1 7,5 Fig. 1: Dimensions (all measurements in mm) We reserve the right to modify the dimensions and design as part of the ongoing technical development process. Description The electronic room thermostat detects the current...
  • Page 9: Operation

    Operation Controls Fig. 2: Controls 1: Segment display 3: Adjusting buttons "+" and "-" 2: Switching status display of the relay (LED dis- play)
  • Page 10 REMKO thermostats Overview of range + und - + and - + und - + and - + oder - + or - (short) (kurz) (>3s) (>3s) Display of the current Anzeige Ist-Temperatur temperature Setting the target Operating hours counter...
  • Page 11: Installation

    Installation SP-H: Upper setpoint limit Determination of the maximum adjustable setpoint The electronic temperature controller is suitable for -15°C to 99.9°C in 0.1°C steps wall mounting with a surface-mounted cable inlet. If an external probe is used, please observe the Attention: The setting value of the lower setpoint following instructions.
  • Page 12: Electrical Wiring

    REMKO thermostats Electrical wiring Electrical drawings Important information prior to installation DANGER! All electrical installation work is to be performed by specialist companies. Disconnect the power supply when connecting the electrical terminals. NOTICE! Errors on connection can cause damage to the...
  • Page 13: Index

    Index General ......4 Identification of notes ....4 Controls .
  • Page 14 REMKO thermostats...
  • Page 16 REMKO QUALITY WITH SYSTEMS Air-Conditioning | Heating | New Energies Telephone +49 (0) 5232 606-0 REMKO GmbH & Co. KG Hotline within Germany +49 (0) 5232 606-0 Klima- und Wärmetechnik Telefax +49 (0) 5232 606-260 Im Seelenkamp 12 E-mail info@remko.de...

Table of Contents