Advertisement
Quick Links
CP4000-D
CENTER PUNCH TOOL
Operating Instructions
Cordless Center Punch Tool
BAND-IT IDEX, Inc.
Document # P50986 Rev.A
A Unit of IDEX Corporation
© Copyright
www.BAND-IT-IDEX.com
4799 Dahlia Street
BAND-IT IDEX, Inc. 2021
Denver, CO 80216-0307 USA
All Rights Reserved
P: 1-800-525-0758
F: 1-800-624-3925
1
Advertisement
Summary of Contents for Idex BAND-IT CP4000-D
- Page 1 CP4000-D CENTER PUNCH TOOL Operating Instructions Cordless Center Punch Tool BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. 2021 Denver, CO 80216-0307 USA All Rights Reserved P: 1-800-525-0758...
-
Page 2: Table Of Contents
Clamp Application: Center Punch Clamps ................... 11 Clamp Inspection ......................... 12 Maintenance ..........................14 BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. 2021 Denver, CO 80216-0307 USA... -
Page 3: Warranty And Safety Guidelines
Disregard of this caution voids the warranty of the tool and releases BAND-IT of any and all liabilities arising from such misuses. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. -
Page 4: Setup Instructions
This tool was designed for and can only be used with BAND-IT 5/8” Center Punch Clamps. Do not attempt to use on any other type of clamp style. Figure 1 BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. 2021... - Page 5 Figure 3: Align the end of the Tension Screw with the slot in the end of the Drill Clutch during assembly, as shown above. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc.
-
Page 6: Tool Settings
Battery Recommendation: In order to maintain consistent tension when installing clamps, Band-It recommends that the drill be recharged once the indicator on the battery drops to 1 out of 4. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. -
Page 7: Parts List
PIN, CLEVIS, 1/4 X 1-1/4 PUNCH REPAIR KIT T32190** INCLUDES RETAINING BALL AND PUNCH BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. 2021 Denver, CO 80216-0307 USA... -
Page 8: Exploded View
CP4000-D CENTER PUNCH TOOL Exploded View Figure 4 BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. 2021 Denver, CO 80216-0307 USA All Rights Reserved P: 1-800-525-0758 F: 1-800-624-3925... - Page 9 CP4000-D CENTER PUNCH TOOL Tension Gripper Assembly Figure 5 BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. 2021 Denver, CO 80216-0307 USA All Rights Reserved P: 1-800-525-0758...
- Page 10 CP4000-D CENTER PUNCH TOOL Tool Head Assembly Figure 6 BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. 2021 Denver, CO 80216-0307 USA All Rights Reserved P: 1-800-525-0758...
-
Page 11: Clamp Application: Center Punch Clamps
3-5 times handle to the down position. with a hammer or mallet. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. 2021 Denver, CO 80216-0307 USA... -
Page 12: Clamp Inspection
This allows hose to “settle” under the band of the clamp. This hose material attribute is called Cold Flow. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. - Page 13 Drill Switch go as Tension Block nears its end of travel. Reverse drill and send Tension Block all the way forward for a second pull on the band. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc.
-
Page 14: Maintenance
Re-attach Tool Head to Tool Body, making sure that load bearing tip extends into Tension Screw. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc. - Page 15 Blade and tighten the Blade Mounting Screws approximately 120 in-lbs. Reattach Tool Adapter to Center Punch Tool. Reattach Tool to Drill and drive Tension Block all the way forward. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc.
- Page 16 Punch Assembly. Press out spring pin so that Punch Holder can be removed from Punch Arm. Remove retaining ball and replace punch. To reassemble, repeat these steps in reverse order. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc.
- Page 17 Slot Plate and Blade. After reassembling, tighten ¼” socket screws to 90-110 in-lbs. Note: Drills needing repair must be returned to Band-It. BAND-IT IDEX, Inc. Document # P50986 Rev.A A Unit of IDEX Corporation © Copyright www.BAND-IT-IDEX.com 4799 Dahlia Street BAND-IT IDEX, Inc.