Advertisement
Quick Links
Advertisement
Summary of Contents for Smart Park PDC125 PI
- Page 1 PDC125 PI Operation Manual Version 1.0 Installation Manual Version 1.0...
- Page 2 1. Introduction Thank you for purchasing Smart Park®. Your Smart Park® is a multifunction system, the system functions as a supplemental feature on your vehicle to assist you in avoiding obstacles while reversing and for low speed forward movement (if additional module is installed).
- Page 3 Auto-Mute Button At any time the Smart Park® system can be muted by pressing the automute button (see your installer for button location). This will mute the system until the vehicle ignition is turned off.
- Page 4 Operation Manual iii. Learning Capability Your Smart Park® system can learn to ‘ignore’ vehicle mounted obstacles (eg tow-hitch, low rear-mounted tyre, bicycle rack etc..) that would otherwise cause false alerts. To ‘teach’ your vehicle to ignore these obstacles place the vehicle in reverse for 2 second. Place the vehicle in park / neutral for 1 - 2 seconds.
-
Page 5: Basic Function
Operation Manual 3. Basic Function i) Rear Protection System The rear sensors are activated when the vehicle is placed in reverse gear. The system will beep once to confirm successful self-check and then will remain silent unless an object is detected. On initial detection of an obstacle the system will beep slowly and the green LED will flash. -
Page 6: Troubleshooting
0.4m – 0m 1.3ft – 0 ft 4. Trouble Shooting All problems with Smart Park® must be repaired by an authorized provider. Should your Smart Park® unit not function correctly or should you hear more than the standard one beep self-check tone then immediately take the vehicle back for repair. - Page 7 Operation Manual Notes:...
- Page 8 Installation Manual Installation Manual 1. Required Tools List Screwdrivers Marker pencil Electric Drill Smart Park® SPC-3 Drill bit Smart Park® SPC-4 Drill bit Plyers Panel Removal Tool Soldering Iron & Solder Voltmeter Safety Glasses 2. Supplied Parts List Control Module...
- Page 9 Installation Manual 3. Application Guide Bumper Type Bumper Angle Supporter Cutter +2º - -2º SPC-3 Not Required Plastic +2º - -2º SPC-4 Yes-Flat +2º - -2º SPC-4 Yes-Flat SPC-4 -2º - -10º Yes - Angled...
- Page 10 Installation Manual 4. Painting Sensors & Supporter 5. Position and Mark Bumper for Drilling...
- Page 11 Installation Manual 6. Insert Sensors into Supporter (if required) Align the small line on supporter with the top line on sensor Do not rotate sensor sideways 7. Drill Bumper – ONLY USE SPC cutter 8. Insert Sensors into Bumper...
- Page 12 Installation Manual 9. Connect Sensors into Extension cable Caution! Please ensure the plug is securely pushed together and screwed tight! Ensure cable is attached to the correct sensor 10. Adjust Initial Control Unit Dip Switch Settings SETTING SWITCH 1 SWITCH 2 SWITCH 3 SWITCH 4 Full Detection...
- Page 13 Installation Manual 12. Install Speaker/LED and connect to Control Unit Speaker can be mounted using the mounting point or using the supplied Velcro tape The speaker/LED should be placed in view of the driver – in the dash area for a front system or high at the back of the vehicle for a rear system.
- Page 14 Installation Manual 14. Connect Wiring Harness to Vehicle Black – Ground (Use the ring terminal to connect ground wire to vehilce body directly) Red – 12v Power (Reverse power for Rear system, Accessory power for Front system) Orange – 12v Accessory Power (only required Rear system mute function) Connect Sensors and Harness to Control Unit...
- Page 15 Installation Manual 16. Activate Rear System & Test Steps: 1. Start Vehicle 2. Place in Reverse Gear 3. Listen for 1 self-diagnostic beep and a green light of LED to confirm correct function. 4. Test system by reversing vehicle to each zone and checking accuracy.
- Page 16 Installation Manual 17. Set Learning System (if required) If there is something mounted on the vehicle that is causing the sensors to false alarm (tow bar, rear mounted tyre, bicycle rack etc..) you can “train” the system to ignore these obstacles.
- Page 17 Installation Manual 19. Test Front System There are only two zones in the front system: Zone 2: 0.8m – 0.4m / 2.5ft - 1.3ft Zone 1: 0.4m – 0m / 1.3ft - 0ft...
- Page 18 Installation Manual 20. Diagnostics The Smart Park® system performs a self-check on startup. Below is a brief diagnostic chart should there be a system fault.: REAR BUMPER Sensor Speaker/LED Signals Speaker Sound LED Display System has been programmed Yellow Long single beep...
- Page 19 Dealership. Should your Smart Park™ system fail to perform return it to the original selling dealership for replacement. Smart Park® will replace it with a new or similar unit.
- Page 20 www.smartpark.net For our full range of driver assistance and safety products: 4”, 5.6”, 7” Monitors SmartFrame Cameras Reversing Sensors Flex Camera Factory Display Commercial Integration Units Camera Systems LCD Mirror GM Bracket HitchView Bumper Monitors Camera Camera...
Need help?
Do you have a question about the PDC125 PI and is the answer not in the manual?
Questions and answers