AES global DECT Extra Manual

DECT Extra Handset Guide
* ALWAYS RANGE TEST THE UNIT ON SITE BEFORE INSTALLATION *
Portable Audio Handset
Call Another Handset
Press and the unit will display 'HS1', 'HS2', 'HS3', 'HS4'
depending on how many handsets are coded in the system.
Then use the and you can select the handset you wish
to call and then press to start the call.
OK
Adjusting Relay time
Press Relay 2 button for 3
seconds, scroll through
menu until you see 'ti'.
Press to select 'ti'
OK
and adjust your relay
times. Press to select
OK
your relay time. Press
ON/OFF
to end the process. Both
relays will have the same
relay time.
RELAY 2
HANDSET BATTERIES INCLUDED
(2 x AAA 600mA Rechargeable)
Voicemail
When a call is not answered within 40 seconds,
the visitor can leave a message. Once complete,
the handset will display the symbol.
The unit can store up to 16 voice messages.
To listen to a voicemail, press . If there is more than 1 use
OK
and press to play. Press
OK
PAIRING
LED
BATTERY
RECEPTION
INDICATOR
TI : ME
OK
CODE BUTTON
Change Ring Tone
Press and the handset will ring with its
currently selected tone. Then you can press the
and keys to cycle through the available ring
RELAY RELAY
tones. Then press
1
2
and
once to Delete the message or press and hold to delete all.
Change Ring Volume
Press and to increase or
decrease the ring volume and
then press to save.
OK
LEVEL
VOICEMAIL
SYMBOL
RELAY 1
Handsets will be
displayed in order
of H1, H2, H3 & H4.
(only 1 handset per
button)
24V
to select and save the tone.
OK
AC DC
IN
to select the message required
12V
OUT
RE-CODING/ADDING EXTRA HANDSETS
1
Occasionally the system may need to be re-coded once installed.
If the handset does not ring when the call button is pressed,
2
the system may need to be re-coded.
3
( ● = FULL RE-CODE : STEP 1-5 )
4
(● = ADDING A HANDSET : STEP 3-5 )
C
TRANSMITTER
CODE BUTTON
603/703 DECT
●
Step 1) Press and hold the CODE BUTTON inside the Transmitter Module for 5 seconds
until the audible tone is heard from the Intercom speaker.
( On 603 Transmitter the blue LED marked D17 should also flash. )
●
Step 2) Then press the CODE BUTTON 14 times and wait until the melody is heard or the
LED turns off. Performing this step will remove ALL handsets currently synced (or partially
synced) to the system.
( Note: Doing this step will also clear ALL voicemails after reset. )
●●
Step 3) Press and hold the CODE BUTTON
until the audible tone is heard from the Intercom speaker.
( On 603 Transmitter the blue LED marked D17 should also flash. )
●●
Step 4) Then press and hold the CODE BUTTON
top begins to flash, after a few seconds you will hear a melody play to let you know it has
successfully connected.
( Repeat Steps 3 & 4 for each new handset. )
●●
Step 5) Finally you should test the kit to ensure that everything is working as expected
by pressing the Call Button on the CallPoint to ensure the handset and/or wall mounted unit
receives the call and that the two way speech is functioning correctly.
Wall/Desk Mounted Audio Panel (603 / 703 / 705)
Example shows the
location of the CODE
BUTTON that can be
found on the back of
the wall mounted unit.
TI : ME
CODE BUTTON
Can be found on
reverse side.
STILL HAVING TROUBLE?
Find all of our support options such as Web
Chat, Full Manuals, Customer Helpline and
more on our website:
WWW.AESGLOBALONLINE.COM
705 DECT
inside the Transmitter Module for 5 seconds
on the handset until the red LED at the
OK