Related Manuals for Ayce YT4302-09
Summary of Contents for Ayce YT4302-09
- Page 1 Original instructions INSTRUCTION MANUAL Electrical Chain saw YT4302-09/BG PRO CS2400 - 17 2400W 03/2017...
- Page 2 Description of the symbols Indicates danger, warning, or caution. WARNING – To reduce the risk of injury, user must read instruction manual. These symbols indicates the requirement of wearing ear protection, eye protection, dust mask and gloves when using the product. Wear safety boots Do not expose to rain Remove plug from the mains immediately if the cable is damaged or cut...
-
Page 3: General Tool Safety Warnings
The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. - Page 4 c) Do not expose tools to rain or wet conditions. Water entering a tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the tool. Keep cord away from heat, oil, sharp edges or moving parts.
- Page 5 f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
- Page 6 a) Have your tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the tool is maintained. b) Caution! If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in order to avoid a safety hazard.
- Page 7 contacting a "live" wire may make exposed metal parts of the tool "live" and could give the operator an electric shock. When cutting a limb that is under tension be alert for spring back. When the tension in the wood fibers is released the spring loaded limb may strike the operator and/or throw the chain saw out of control.
- Page 8 Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below: Maintain a firm grip, with thumbs and fingers encircling the chain saw handles, with both hands on the saw and position your body and arm to allow you to resist kickback forces.
- Page 9 during cutting. Attention for usage of electric chain saw Before any cutting, you must wait for the saw chain running to reach a stable speed. When cutting wood, please do not press the chain saw with big force. ...
- Page 10 Technical specifications Model YT4302-09 Voltage: 220-240V~ 50Hz Power 2400 W No load speed 13.5 m/s Guide bar length 405 mm Guide bar OREGON-160SDEA041 Saw chain OREGON-91PJ057X Chain pitch 9.53 mm Chain gauge 1.27 mm Driving Sprocket 6 Teeth Net Weight (with guide bar and chain) 5.4 kg (max)
- Page 11 List of main parts (Fig.2) Fig.2 sprocket cover 11. oil bottle hand wheel 12. saw chain 3. tension adjustment hand wheel 13. bar front handle 14. bar cover 5. brake guard 15. power cord oil tank cap 16. rear handle retaining block 17.
- Page 12 Assembly Mounting the chain bar WARNING! The saw chain has very sharp edges. Use protective gloves for safety. The saw chain and bar are packed separately in the carton. 1) Place the saw on a firm surface. Fig.3 Fig.3 2) Remove sprocket cover by loose the hand wheel on sprocket cover. Fig. 4 Tighten Loosen Fig.4...
- Page 13 4) Place the saw chain and guide bar assembly around the sprocket. Check to make sure that the tensioning pin insert into the hole on the bar and the sprocket cover insert onto the location pin. (fig.6) Fig.6 5) Rotate the hand wheel to fix the sprocket cover first, but do not tight it. Fig.7&8 Fig.7 Fig.
- Page 14 light force from the middle finger and thumb. There should be no sag between the guide bars. b) Rotate the hand wheel to loosen the sprocket cover first, but do not remove it and make the tensioning pin on the sprocket cover get out from the hole on the bar. c) Rotate the tensioning wheel to increase or reduce the chain tension.
- Page 15 Checking the automatic oil function Check the automatic operation of the chain lubrication by pointing the tip of the switched –on saw towards a piece of paper laying on the ground, if a patch of oil appears and becomes larger, then the automatic oil function is working. If there are no traces of oil even though the oil tank is full.
- Page 16 Never try cutting through two logs at same time, only cut one log at a time. Do not bury guide bat nose or try plunge cut(boring into wood using guide bar nose) Watch for shifting of wood or other forces that may pinch chain. Use extreme caution when reentering a previous cut.
- Page 17 Start up 1. remove the bar cover 2. release the chain brake by pulling the front hand guard(5). Firmly towards the back of the electric chain saw until a click is heard, to check the chain brake has been released, you should be able to move the chain by hand. (fig.14&fig.15) Fig.
- Page 18 Trimming a tree is the process of cutting limbs from a living tree, makes sure your footing is firm keep feet apart. Divide your weight evenly on both feet. Follow directions below to trim a tree. 1. make first cut 15 centimeters from tree trunk on underside of limb, use top of guide bar to make this cut.
- Page 19 Felling a tree When bucking and felling operations are being performed by two or more persons at the same time, the felling operations should be separated from the bucking operation by a distance of at least twice the height of the tree being felled. Trees should not be felled in a manner that would endanger any person, strike any utility line or cause any property damage.
- Page 20 Notching undercut Make the notch 1/3 the diameter of the tree, perpendicular to the direction of falls as illustrated in Figure 18. Make the lower horizontal notching cut first. This will help to avoid pinching either the saw chain or the guide bar when the second notch is being made.
- Page 21 Limbing a tree Limbing is removing the branches from a fallen tree. When limbing leave larger lower limbs to support the log off the ground. Remove the small limbs in one cut as illustrated in Figure 19. Branches under tension should be cut from the bottom up to avoid binding the chain saw.
- Page 22 Fig. 21 Log supported one end Fig.22 Log supported both ends Fig.23 Bucking a log 03/2017...
- Page 23 Cleaning and maintenance Cleaning saw body Warning : unplug chain saw from power source before servicing, sever injury or death could occur from electrical shock or body contact with moving chain. Warning: cutting edges o chain are sharp, use protective gloves when handling chain. Warning: cleaning saw body.
- Page 24 Chain sharpening (fig26.&fig.27& fig,28) Warning : Always ensure that the tool is switched off and the plug is removed from the power point before making any adjustments or maintenance procedures. The chain requires sharpening when the chain saw does not cut appropriately. This operation is performed as follows : 1.
-
Page 25: Eu Declaration Of Conformity
EU declaration of conformity 1. Apparatus model/Product Product: Electrical chain saw type: YT4302-09/ BG PRO CS 2400 - 16 batch or serial number: 1601-2012 2. Name and address of the manufacturer or his authorised representative: CASA POR ITM SA – Lugar do Marrujo – Bugalhos – 2384-004 Alcanena - Portugal SAS EQUIPEMENT DE LA MAISON –... - Page 26 Parc de Tréville, 2 allée des Mousquetaires 91078 Bondoufle cedex - France Signed for and on behalf of: Place : Alcanena date of issue 16/03/2016 Signee: 03/2017...