Subscribe to Our Youtube Channel
Summary of Contents for Quick QNN
- Page 1 REV 000A QNN INTERFACE Gyro 1: Speed 0% GATEWAY Gateway QNN INSTALLATION AND USE MANUAL EN - Pag. 4...
- Page 3 Pag. 6 2 - Supplied parts Pag. 7 2.0 - Package contains the following parts Pag. 7 2.1 - Required components, available for the QNN Pag. 7 2.2 - Compatible accessories for use QNN Pag. 7 3 - General information Pag.
-
Page 5: Information About The Product
• Solid and compact design with IPX7 degree of protection (front). Quick® reserves the right to make changes to the technical characteristics of the device and the content of this manual without prior notice. *For more details consult the manufacturer of the chart plotter in use... -
Page 6: Technical Data
5 - 85% RH, non-condensing Protection Class IPX7 GENERAL FEATURES Weight 280 g EN 60945, EMC Emissions and Immunity for marine applications Dimensions in mm (inch) 53 (2 3/32) 132,5 (5 7/32) 152 (5 63/64) INSTALLATION AND USE MANUAL QNN - REV000A... -
Page 7: Supplied Parts
Quick® Gateway QNN has been designed and constructed for the purposes described in this instruction manual. The “Quick®” Company does not accept any responsibility for direct or indirect damage caused by improper use of the equipment, bad installation or by possible errors occurring in this manual. -
Page 8: Cleaning The Appliance
QNN You are aware and accept to be the only persons responsible for use of the QNN and all decisions taken as a result. In using this service, you free Quick SpA and waive presenting any claims in relation to this service. -
Page 9: Installation Procedures
After choosing where to position the instrument, proceed as follows: TEMPLATE TO INSTALL GATEWAY SCREW ✔ ✔ ✘ INSTALLATION AND USE MANUAL QNN - REV000A... -
Page 10: Electrical Connection
CAN-1 PORT CHC, SRC NRG+, INVERTER CAN-0 PORT THRUSTER ALIMENTAZIONE + VDC COMMON Very low voltage safety power supply unit. Limited power source. Do not open the panel casing when devices are live. INSTALLATION AND USE MANUAL QNN - REV000A... -
Page 11: Connection Indications
1 TX + 1 TX - ALIMENTAZIONE 9-32V 1 RX + 1 RX - USB FEMALE 2 TX + TYPE A 2 TX - 2 RX + 2 RX - CAN 0 CAN 0 INSTALLATION AND USE MANUAL QNN - REV000A... -
Page 12: Connection Example
6 - Electrical connection CONNECTION EXAMPLE QNN gateway - plant description A - RC REMOTE CONTROL MC² Quick Gyro B - Control CHC when terminator is not built-in CABLE ETH 1 ESEMPIO COLLEGAMENTO SIMRAD ANCHORING SYSTEM THRUSTERS GYRO STABILIZER 0.0 meter 0.0°... - Page 13 Electrical connection of accessories For the electrical connection of accessories, refer to the dedicated manuals. A - Remote control panel MC² Quick Gyro: Manual REMOTE CONTROL PANEL B - Control CHC: Manual Chain counter CHC C - LDIM BUS RGBW: Manual Led dimmer LDIM BUS RGBW...
-
Page 14: Control Panel
GREEN FLASHES SLOWLY ERROR DURING THE LAST OPERATION GREEN FLASHES QUICKLY OPERATION IN PROGRESS ETHERNET 0 - ETHERNET 1 GREEN LED STATUS DESCRIPTION GREEN OFF NO CONNECTION RED OFF GREEN FLASHES CONNECTED RED STEADY INSTALLATION AND USE MANUAL QNN - REV000A... -
Page 15: Maintenance
After completing the electrical connections, just connect the Gateway to the Chart plotter. Thanks to the plug & play system, all of the calibrations made on the Quick products’ systems or from the chart plotter are automatically shared between the two systems (Quick and chart plotter). The chart plotters suitable for the QNN Gateway are the latest generation ones with HTML5. -
Page 16: Keys And Functions
10 - Using the control interface Use of the QNN interface does NOT replace the control panels dedicated to the Quick products. The interface must be used with full knowledge of the facts and to facilitate the functions of the connected Quick products. -
Page 17: Active And Inactive Icons
Windlass - Thrusters - Gyroscopic Stabilizers - Battery Charger - Inverter (currently not available) - Lights ACTIVE AND INACTIVE ICONS Home shows the Quick accessories that are connected and not connected. If they are not connected, the icon for the accessory will be visible but inactive (GHOST). -
Page 18: General Setup
SW Release 01.00.00 DESCRIPTION OPERATION Login Access restricted to Quick® technicians for advanced settings Measure Unit Choose the unit of measure save/load setting Backup. Use a formatted USB drive (to perform the backup, insert the drive and press SAVE. The backup was successful if the folder is found on the drive) -
Page 19: Anchoring System
Quick chain counter/windlass rope management page. Ability to weigh and drop anchor, Quick control panels can be connected to the PCS family version 62.37 and the CHC version 2.15 and later (for use and installation of the control panels, refer to the dedicated manuals). - Page 20 Key to pass to warping mode, use (external) commands. Chain Key to pass to windlass mode It is possible to weigh/drop the anchor using the Quick electric commands; the QNN will measure the length of the chain dropped. More information - Manual PCS - CHC 1203...
- Page 21 PCS from version 60.37 (for use and installation of the control panels, refer to the dedicated manuals). The QNN may not be used as a single manoeuvring instrument but must be associated to its primary control panels. Thruster System...
- Page 22 GYRO STABILAZER - Quick stabilizing monitoring Mirroring page In the MC² Quick Gyro page, the functions of the Remote MC² Quick Gyro panel functions are mirrored. It is possible to access the commands to turn the stabilizer(s) on/off, and to display its(their) status and correct operation To use the command, refer to the RC - Remote Control MC²X - Quick manual...
-
Page 23: Battery Chargers
10 - Using the control interface 10.7 - Battery chargers BATTERY CHARGERS - Quick battery charger monitoring page Management of several battery chargers at the same time. SBC NRG+ Battery Charger MODE: Absorbtion STATUS: OK SBC: 600 NRG+ CHARGER: A1... - Page 24 Switching on/off of lights and colour/tone management. Follow the configuration procedure on page 24, chapter 10.7. Activation of Lighting function. When the QNN is installed or updated, the key representing the lighting function in the HOME screen will appear inactive (GHOST). To activate it, hold down the lighting key until it...
- Page 25 8. Device category selection Select the icon of the lighting category. Options: Downlight A, Downlight B, Linear A, Linear B, Applique, Table light, Courtesy, Underwater. The selected box will have a green frame. INSTALLATION AND USE MANUAL QNN - REV000A...
-
Page 26: Alarms And Troubleshooting
3. If the problem is not resolved, contact the Quick® customer service for support GYRO STABILAZER If the Remote Controls on the stabilizer cannot communicate with the QNN, make sure the IP address on the RC (remote controls) is different than the one in the QNN. - Page 28 REV 000A USER MANUAL Product serial code QUICK S.p.A. - Via Piangipane, 120/A - 48124 Piangipane (RAVENNA) - ITALY ® Tel. +39.0544.415061 - Fax +39.0544.415047 - www.quickitaly.com - quick@quickitaly.com...
Need help?
Do you have a question about the QNN and is the answer not in the manual?
Questions and answers