Table of Contents
Summary of Contents for Zip Water Zip HydroTap G5
- Page 1 uick Start Installation Guide HydroTap G5 Command Centre Boiling/Chilled models AFFIX PRODUCT LABEL HERE Australia Visit our website to download the manuals Quick Start Installation Guide 807118 v1.06 10.22 G5 BC Quick Start Guide...
-
Page 2: Table Of Contents
Table of contents SECTION 1: Using these instructions Before you start SECTION 1: Using the instructions ..............3 SECTION 2: IMPORTANT SAFETY INSTRUCTIONS ..........4 This document is a Quick Start Installation Guide. SECTION 3: WARNINGS AND REGULATORY INFORMATION ......7 For further details on installing and operating your HydroTap SECTION 4: Technical data ................ -
Page 3: Section 2: Important Safety Instructions
SECTION 2: IMPORTANT SAFETY INSTRUCTIONS SECTION 2: IMPORTANT SAFETY INSTRUCTIONS in a safe visible position for connection. Venting Sometimes steam and / or boiling water droplets may discharge through a vent outlet on the tap. If not using the font, ensure the tap body is located Compliance so the tap outlet safely dispenses into the sink bowl. -
Page 4: Section 3: Warnings And Regulatory Information
SECTION 2: IMPORTANT SAFETY INSTRUCTIONS SECTION 3: WARNINGS & REGULATORY INFORMATION • For continued safety of this appliance it must be installed, operated and maintained in accordance with the manufacturer’s instructions. • This appliance may deliver water at high temperature. Refer to the Plumbing Code of Australia (PCA), local requirements Compressed gas warning and installation instructions to determine if additional... -
Page 5: Section 4: Technical Data
SECTION 3: WARNINGS & REGULATORY INFORMATION SECTION 4: Technical data pressures above the maximum limits stated. • Use of tools can be hazardous. Assess the risks before you start. Power rating, kW Dimensions Weight Model • A clearance envelope around all Command Centres must be provided 220-240V, 50Hz W x D x H (mm) (kg) - Page 6 SECTION 4: Technical data SECTION 5: Parts supplied BC H Water supply pressure requirements Parts supplied with the HydroTap for Work for Work for Home Min - Max pressure, kPA (bar) Component Australia HydroTap tap HydroTap 170 (1.7) - 700 (7.0) 170 (1.7) - 500 (5.0) HydroTap pipes, tubes hoses and fittings ...
-
Page 7: Section 6: Set Up The Ventilation
SECTION 6: Set up the ventilation SECTION 6: Set up the ventilation BC100 - BC40 models Use of tools can be hazardous. Assess the risks before you start. • Cold air is drawn in through the inlet vent and gap provided by the door buffers. -
Page 8: Section 7: Connect The Water Supply
SECTION 6: Set up the ventilation SECTION 7: Connect the water supply BC30, BC20 & Home models Valves and fittings must be sealed with PTFE tape if compression seals are not included. • Cold air is drawn in through the inlet vent and lower gap provided by the door buffers. -
Page 9: Section 9: Fit The Booster
SECTION 8: Set the bypass & install the limescale filter SECTION 9: Fit the Booster Available as optional accessory - UK only. • Supplied with selected models, or available as an optional accessory. For filter head and scale filter installation use the guide supplied Booster with the filter head and filter respectively. -
Page 10: Section 10: Connect The Booster
SECTION 10: Connect the Booster SECTION 11: Connect the Command Centre Generic installation instructions For HydroTap, mixer tap and any optional accessories, use instructions supplied with individual kit components. Booster Mains power cable Braided hose HydroTap Do not connect to electrical power until commissioning. Do not over tighten hose connections. - Page 11 SECTION 11: Connect the Command Centre B res comm SECTION 11: Connect the Command Centre Booster (selected models) and BC40, BC60, BC100 models BC20, BC30, BC Home models limescale filter (optional) Booster (selected models) and BCS comm BC comm BYPASS VENT BYPASS MAINS...
-
Page 12: Section 12: Commissioning
SECTION 12: Commissioning SECTION 12: Commissioning The HydroTap Clean process 12. Commissioning the HydroTap using the HydroTap Clean can HydroTap Clean is a first to market cleaning process for HydroTap systems 12.1 Turn on the supplies & familiarise yourself with the system comprised of the HydroTap Clean solution, dosing adaptor and smart •... - Page 13 SECTION 12: Commissioning SECTION 12: Commissioning 12.3 Install the filter cartridge 12.5 Filter flush • Unpack filter cartridge. • Follow the steps on-screen to flush the filter. • Remove dust cap and set aside in a clean area for use later. •...
- Page 14 SECTION 12: Commissioning SECTION 12: Commissioning 12.6 System priming HYDROTAP CLEAN PREPARATION 12:12 PM Step 3. • Read the on screen information. Install HydroTap Clean adapter (1) into filter head. SYSTEM PRIMING 12:12 PM • Touch the run arrow to go to the next The system reticulation will be primed Step 4.
- Page 15 SECTION 12: Commissioning SECTION 12: Commissioning 12.8 Boiling calibration and cleaning Filter head and HydroTap Clean adapter (1) • Read the on screen information. BOILING CALIBRATION & CLEANING 12:12 PM Info • BC systems offer combined boiling This will optimise the performance of the boiling unit and perform chilled cleaning.
- Page 16 SECTION 12: Commissioning SECTION 12: Commissioning • Read the on screen information and • Remove the HydroTap Clean adapter (1) RE-INSTALL FILTER 12:12 PM instructions. While Boiling Calibration in Progress..from filter head. Step 1. • Note When the cleaning process Ensure cloth is below HydroTap Clean can (2).
- Page 17 SECTION 12: Commissioning SECTION 12: Commissioning 12.9 Tank flush • Note For all boiling models, if after EMPTY HOT TANK 12:12 PM filling the hot tank during the tank flush • Read the on screen information and TANK FLUSH 12:12 PM WARNING ! Boiling water process, the hot water temperature is will be dispensed ! Check...
- Page 18 SECTION 12: Commissioning Notes 12.11 Safety sensor calibration (Classic boiling models only) Optional, in cases where light recalibration is required. Light intensity varies from site to site, therefore it is recommended that a re-calibration be performed at the time of the installation.
- Page 19 Tel (+612) 9796 3100 Free call 1800 947 827 (1800 ZIP TAP) www.zipwater.com WMKA00099 AU02691 AS 3498 Zip Water UK Trafalgar House, Rash’s Green, Dereham, Norfolk, NR19 1JG 0345 6 005 005 sales@zipindustries.co.uk specify.zipwater.co.uk As Zip policy is one of continuous product improvement, changes to specifications may be made without prior notice.