Advertisement
WARNING! Ensure the light is correctly charged before initial use.
!
DO NOT allow children to use the light.
#
DO NOT use if the battery or the light casing is damaged.
#
When not in use store the light in a safe, dry, childproof location.
"
1.3 BATTERY SAFETY INSTRUCTIONS
!
WARNING! Powered by a sealed lead-acid battery which can be dangerous if not handled with care.
Charge battery prior to first use. The battery pack will have been shipped in a low charge state. Minimum
"
initial charge time 24 hours.
DO NOT charge battery when room temperature is below 10
#
DO NOT attempt to recharge the battery by means of an engine generator or a DC power source.
#
DO NOT short-circuit the battery by linking both terminals with a metal object.
#
DO NOT store the battery (or light) in locations where the temperature may exceed 40
#
outside sheds, above heaters, or metal buildings in summer.
WARNING! Dispose of spent battery correctly and in accordance with local regulations as it contains acid.
!
DANGER! DO NOT attempt to dismantle the battery pack. For safety and environmental reasons DO NOT
discard in domestic waste or by burning. ONLY discard or recycle according to local waste authority
regulations.
!
WARNING! DO NOT allow a leaking battery to come into contact with your skin. If you come into contact
with battery fluid take immediate action:
a) Skin contact: Wash immediately with soap and water.
b) Eye contact: Flush eye immediately with cool, clean running water for at least 15 minutes and seek
immediate professional medical attention.
2.
INTRODUCTION & SPECIFICATIONS
Fluorescent tube flexibly mounted in base, producing knock-resistant
lamps. 12V Light unit for electrical safety, powered by lead acid
battery in base. Up to ten hours continuous use from a fully charged
battery. Fitted with a 12V 3A cigarette lighter outlet. Splash-proof
construction with non-slip base and extending carry-handle. Base
will accept 18 or 36W light units. Supplied with mains battery
charger.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . .ML20
Tube: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18W
Tube Length: . . . . . . . . . . . . . . . . . . . . . . .600mm
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . .12V 12Ah
Operating Time (max.): . . . . . . . . . . . . . . . . .10hrs
Overall Height: . . . . . . . . . . . . . . . . . . . . . .800mm
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . .ML40
Tube: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36W
Tube Length: . . . . . . . . . . . . . . . . . . . . . . .1200mm
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . .12V 12Ah
Operating Time (max.): . . . . . . . . . . . . . . . . .6.5hrs
Overall Height: . . . . . . . . . . . . . . . . . . . . .1380mm
3.
ASSEMBLY
3.1
ASSEMBLY
3.1.1 To assemble the wobble light, remove the product from its
boxes carefully.
3.1.2 Screw the plastic tube into the base. To assist its progress, a
little vaseline or WD40 can be used on the plastic threads. Do
not allow any lubricant to coat the connector pins at the
base of the tube.
C (50
F) or above 40
C (104
F).
O
O
O
O
C (104
F) such as
O
O
ML20
4.
OPERATION
Fig 1
5.
MAINTENANCE
WARNING! Before replacing the fluorescent tube or performing any
!
maintenance the unit must be switched off and not connected to the
charger.
!
WARNING! Do not turn the unit on with the transparent cover removed or
with the tubes removed.
5.1
CHANGING THE FLUORESCENT TUBE
IMPORTANT! Replacement tube must be the same type and rating as the
original tube supplied.
Use Sealey replacement tube (see parts list for part numbers).
5.1.1 Remove the rubber cap located at the top of the tube assembly (fig 2.A).
5.1.2 Turn the inner cap in an anti-clockwise direction and lift to remove (fig 2.B).
5.1.3 The fluorescent tube will now slide straight out of the tube assembly
(fig 2.C). Replace the tube.
5.1.4 Refit the inner cap, making sure the connector lines up with the terminal
situated on the tube assembly and place the rubber cap back on the top.
5.1.5 Ensure that the tubes and caps are correctly installed and seated before
turning on.
5.2
CLEANING
5.2.1 Clean the unit with a damp cloth and a mild soapy solution.
Do not use solvents or abrasive cleaners.
Declaration of Conformity
We, the sole distributor in the UK, declare that the products listed here are
in conformity with the following standards and directives. The construction files for these products are held by the
manufacturer and may be inspected, by a national authority, upon request to Jack Sealey Ltd.
WOBBLE LIGHTS
: ML20-ML40
MODELS
Signed by Mark Sweetman
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
For Jack Sealey Ltd. Sole distributor in the UK of Sealey Power Products.
93/68/EEC Marking Directive
4.1
CHARGING THE UNIT
4.1.1 Insert the charger lead plug into the inlet socket (fig 1.A).
4.1.2 Plug charger into mains socket and switch on.
4.1.3 The red LED (fig 1.B) will light up indicating a current is
present.
4.1.4 Charge for approximately 24 hours.
DO NOT attempt to use the light while it is connected to
#
the charger.
4.2
USING THE LANTERN
4.2.1 To operate the lantern simply flip the power switch
(fig 1.D) either on or off (I/O).
4.3
EMERGENCY LIGHTING
4.3.1 While the unit is plugged into the mains the light will be
disabled, however, if a power cut occurs the light will
illuminate, acting as a temporary emergency light (the
power switch needs to be in the "ON" position).
4.4
DC OUTLET
4.4.1 The DC outlet (fig C) can be used as a charge source to
charge items such as mobile phones.
Fig 2
6th June 2005
ML20-ML40 - 1 - 060605
Advertisement
