Table of Contents
Advertisement
Quick Links
Ratek EOM5 Analogue Orbital Shaker – User Manual
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
User Manual
Analogue Orbital Shaker
Model : EOM5
Version: 1.1 – 01/07/2015
English
www.ratek.com.au
60 Wadhurst Dve, Boronia, Victoria 3155, Australia - P: +613 9887 2161 - F: +613 9887 2163 - E:
sales@ratek.com.au
© All Rights Reserved
Made in Australia, User Manual printed in Australia
Changes without prior notification reserved
Errors and omissions excepted.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Page 1 of 16
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ratek EOM5
Summary of Contents for Ratek EOM5
- Page 1 Ratek EOM5 Analogue Orbital Shaker – User Manual ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- User Manual Analogue Orbital Shaker Model : EOM5 Version: 1.1 – 01/07/2015 English www.ratek.com.au 60 Wadhurst Dve, Boronia, Victoria 3155, Australia - P: +613 9887 2161 - F: +613 9887 2163 - E: sales@ratek.com.au...
- Page 2 Thank you Thank you for purchasing a Ratek product. This User Manual will assist you in the correct installation and operation of the EOM5 Analogue Orbital Shaker, as well as explain the safety requirements for its use. Important: Please read the contents of this User Manual before unpacking and operating the product.
-
Page 3: Table Of Contents
Ratek EOM5 Analogue Orbital Shaker – User Manual ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- TABLE OF CONTENTS PAGE Cash Bo INTENDED USE....................................................................................................................................4 4 4 4 Suitable Articles For Use With This Analogue Orbital Shaker ........................4 Unsuitable Articles For Use With This Analogue Orbital Shaker........................ -
Page 4: Intended Use
Ratek EOM5 Analogue Orbital Shaker – User Manual ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Intended Use This Analogue Orbital Shaker is intended for the purpose of agitating vessels containing liquid to create an orbital mixing action inside the vessel. The Analogue Orbital Shaker is not intended to provide direct-contact between itself and an unprotected medical, food, biological or medico- techno item. -
Page 5: Safety Labels And Markings
• Important: If you have any concerns or questions relating to operator or user safety, please contact the appropriate Ratek Service department before installing and operating the unit. Contact details are provided in this User Manual. -
Page 6: Operating Procedures
Ratek EOM5 Analogue Orbital Shaker – User Manual ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Operating Procedures You must take the time to familiarize yourself completely with the following operating procedures before installing or operating the Analogue Orbital Shaker in order to achieve the best performance and maximum attainable user safety. -
Page 7: Safety Warnings
Ratek EOM5 Analogue Orbital Shaker – User Manual ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Safety Warnings Throughout this User Manual, specific warnings will be supplied which relate to the current operation being referred to. These warnings are supplied in addition to the main warning labels affixed to the product and the key points outlined in the section of this User Manual titled ‘Operator Responsibility –... -
Page 8: Preparation & Installation
Ratek EOM5 Analogue Orbital Shaker – User Manual ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Preparation & Installation The Analogue Orbital Shaker should be installed and operated in strict accordance with the following instructions. CAUTION Be careful when lifting and observe your local operational health and safety requirements for lifting before unpacking the carton. -
Page 9: Using The Analogue Orbital Shaker
Ratek EOM5 Analogue Orbital Shaker – User Manual ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Using The Analogue Orbital Shaker Choosing a Suitable Vessel - The Analogue Orbital Shaker should only be used with vessels that are sealed and are adequately secured to the mixing platform to prevent spillage whilst in use. -
Page 10: Optional Accessories
Optional Accessories The EOM5 platform has a Nitrile rubber mat supplied as standard and will be sufficient to hold most flasks and containers at low speeds. For higher speeds a suitable retaining system would be required. The following optional clips and racks are available from your Ratek dealer. -
Page 11: Routine Cleaning And Maintenance
Ratek are consulted prior to decontamination or cleaning being undertaken if there is any doubt about the compatibility of decontamination or cleaning agents with parts of the Analogue Orbital Shaker or with any materials contained in it. - Page 12 Ratek EOM5 Analogue Orbital Shaker – User Manual ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Maintenance - Unplug the equipment from the mains power supply outlet. - Under good light, carefully inspect the mains power lead and check for any signs of wear, over-extension or damage. If you believe the lead to be damaged in any way, contact your supplier.
-
Page 13: Technical Specifications
Ratek EOM5 Analogue Orbital Shaker – User Manual ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Technical Specifications Power requirements 240v AC / 100 watts Motor Brushless AC Speed Controller Solid State Analogue Speed Range 20 to 200 RPM Variable Drive Belt and pulleys Platform 350 x 350mm with Nitrile mat. -
Page 14: Ratek Service Contact Information
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Ratek Service Contact Information Ratek are here to assist you in getting the most from your Analogue Orbital Shaker. Our friendly staff can you assist you at any stage of the product lifecycle. If you have any concerns or questions regarding the operation of your Analogue Orbital Shaker, please contact us. -
Page 15: Warranty Conditions
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Warranty Conditions This Ratek product is covered by a 3 year parts and 12 months labour return-to-base warranty effective from the date of purchase. The product is manufactured in Melbourne, Australia. The warranty is offered by Ratek Instruments Pty. Ltd. located at 60 Wadhurst Drive, Boronia, Victoria, Australia 3155, phone number +613 9887 2161. - Page 16 Contact the supplier from where the equipment was purchased. If this is not possible, please contact Ratek Instruments either via email to service@ratek.com.au, or phone on +613 9887 2161 during business hours AEST. You may be referred to a local repair agent for service.
Need help?
Do you have a question about the EOM5 and is the answer not in the manual?
Questions and answers