TCS Basys Controls QWL 3.1 2 Series Product Manual

Integrated building manager panel

Hide thumbs

Table of Contents

Quick Links

Download this manual

Product Manual

Description

The QWL 3.1 Rev 2 Series Integrated Building Manager

Panel contains a Ubiquity

ed lighting and energy management controls.

Features

Ubiquity Site Gateway

• Site gateway to Ubiquity: enables controller interoper-

ability with Ubiquity

• Enables Ubiquity to maintain controller programming

and scheduling

• Compatible with all TCS Basys supported controllers

• Controller protocols supported: TCSbus, Modbus

• Supervisory control routines

• Supervisory override strategy

• Auto discovery of networked controllers

• Three integrated RS-485 serial ports

• Additional serial ports can be added via USB ports

• Integrated Ethernet controller with firewall capabilities

• Integrated configuration web page

• User adjustable controller monitoring rate

• Remotely upgradable gateway software

Lighting Controller (SLQ218)

• 365-day programming for each circuit

• Analog input for photo sensor with the ability to

remotely adjust sensitivity level

• Selectable power failure state

• Eight channel lighting schedules for interior and exte-

rior applications

• Digital photocell inputs

• Astronomical clock

• External time clock or occupancy sensor input for

each channel

• Channel status LEDs

• Selectable normally open or normally closed relays

• Built-in 2 Amp relays with hand/off/auto switches

2800 LAURA LANE • MIDDLETON, WI 53562 • (800) 288-9383 • FAX (608) 836-9044 • www.tcsbasys.com

Site Gateway with integrat-

QWL 3.1 Rev 2 Series

Integrated Building Manager Panel

Models to Support Wired and

Wireless Networks

Energy Meter (SEQ100)

Utility Pulse Counting Meter for Monitoring of:

• Electric single and 3 phase kW and kWh

• Gas

• Water

• BTU

Contents

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Factory IP Network Address Configuration

Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

RS-485 Controller Network Wiring & Setup

Gateway Configuration Page

Commissioning Tools

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Programming - Lighting Module . . . . . . . . . . . . . . . . . . . 6

Programming - Pulse Meter . . . . . . . . . . . . . . . . . . . . . . 9

TCS ZigBee Wireless Network. . . . . . . . . . . . . . . . . . . 10

LED Display and Push Buttons . . . . . . . . . . . . . . . . . . 10

Checkout & Troubleshooting . . . . . . . . . . . . . . . . . . . . 10

Factory IP Network Address

Configuration

The QWL 3.1 Rev 2 Series Panels are typically ordered

pre-programmed to customer specific networks and no

additional software configuration is required. This is the

preferred purchasing method.

If a QWL 3.1 Rev 2 Series Panel is purchased without

pre-programming it will be shipped with DHCP client

enabled. The configuration page is available through a

browser for additional configuration of the QWL 3.1 Rev

2 Series Panel local IP address. Contact your network

administrator to determine the local IP address (refer to

the MAC address available on the product label).

v1216.1

. . . . . . . . .

. . . . . . . . . . 3

. . . . . . . . . . . . . . . . . . . . .

Table of Contents

Summary of Contents for TCS Basys Controls QWL 3.1 2 Series

Page 1: Table Of Contents
Product Manual QWL 3.1 Rev 2 Series Integrated Building Manager Panel Models to Support Wired and Wireless Networks v1216.1 Description Energy Meter (SEQ100) Utility Pulse Counting Meter for Monitoring of: The QWL 3.1 Rev 2 Series Integrated Building Manager • Electric single and 3 phase kW and kWh Panel contains a Ubiquity Site Gateway with integrat- •...
Page 2: Mounting
Mounting INPUT WIRING The QWL 3.1 Rev 2 Series Panel accepts two 0 to 5 VDC The QWL 3.1 Rev 2 Series Panel is designed for mount- inputs, 8 dry contact/digital inputs and 4 pulse meter inputs. ing using four #10 pan head screws. POWERING THE QWL 3.1 REV 2 SERIES PANEL When drilling ensure that the QWL 3.1 Rev 2 Series Panel is powered down and all metal shavings are cap-...
Page 3: Rs-485 Controller Network Wiring & Setup
RS-485 Controller Network "B" wires. If the QWL 3.1 Rev 2 Series Panel will be at one end of the network, hard wire a 120 Ω terminating Wiring & Setup resistor across the "A" and "B" terminals at the QWL 3.1 Rev 2 Series Panel (See 1 below).
Page 4: Gateway Configuration Page
Gateway Configuration Page APPLICATION INFORMATION This section contains settings which define how the After connecting and logging in, the operation of the unit QWL 3.1 Rev 2 Series Panel interacts with the controller can be configured by selecting the proper parameters network, and how it communicates the data to the actual for your application.
Page 5: Commissioning Tools
Once you are finished contact TCS Basys Controls to assign or initialize the entering information in this section, click the Update QWL 3.1 Rev 2 Series Panel to a site.
Page 6: Programming - Lighting Module
Programming - Lighting Module The lighting module portion of this panel is an SLQ218. It must be programed using TCS Insight or Ubiquity. CHANNEL EVENT SCHEDULING There are eight independent channels each with its own schedule. If the occupied or “ON” time for a particular day is from 8:00AM to 5:00PM.
Page 7 Select whether you want the time clock output (Digital Output Mode) to be Normally Open or Normally Closed during on periods. The Channel Power Threshold is basically a setpoint to which AI2 is compared to determine when to turn off the selected channel(s).
Page 8 Monitor mode: the digital input acts as a monitor for the HOLIDAY VANISHING DI and has no other function. Choose whether to enable the Holiday Vanishing Feature. If checked, the controller will make the number of days for a holiday 0 after the holiday is over. This will keep the holiday from occurring in subsequent years if it is not ASTRONOMICAL TIME The Astronomical time function may be setup on any of...
Page 9: Programming - Pulse Meter
Programming - Pulse Meter KYZ functionality can be mimicked by using a “Meter Multiplier” value of 2. The utility pulse meter module portion of this panel is an In the following picture, both Type A and C are shown. SEQ100. Three pulses are shown, labelled 1, 2, and 3.
Page 10: Tcs Zigbee Wireless Network
In general, the SEQ100 calculates electric meter con- used to “reboot” the entire QWL 3.1 Rev 2 series sumption and demand as follows: panel. This is accomplished by pushing and holding the button for 5-7 seconds. Note: During a reboot, the lights associated with Demand = (CTValue*MtrConst*MtrMult) the Lighting Module of this product could go out, it is (PPRValue*PulseTimeDiff)
Page 11 RS232/RS-485 Communications Converter - QD1010b • Once a network is wired, you should test communi- cations with all controllers on the network. Find out which controllers communicate and which ones don't. Go to the controllers that don't communicate and ver- ify that the "A"...