Download
Share
Print this page
  1. Manuals
  2. Brands
  3. SUNSET Manuals
  4. Indoor Furnishing
  5. SKYCLOUD MAXI
  6. Assembly instructions manual

SUNSET SKYCLOUD MAXI Assembly Instructions Manual

Bioclimatic system
Hide thumbs

Advertisement

Quick Links

Download this manual
SKYCLOUD
MAXI
B ocl mat c System
Assembly Instruct ons
Four Seasons Comfort

Advertisement

loading
Need help?

Need help?

Do you have a question about the SKYCLOUD MAXI and is the answer not in the manual?

Questions and answers

Related Manuals for SUNSET SKYCLOUD MAXI

Summary of Contents for SUNSET SKYCLOUD MAXI

  • Page 1 SKYCLOUD MAXI B ocl mat c System Assembly Instruct ons Four Seasons Comfort...
  • Page 2 Step 1 Step 2 Act ve Cloud Install ng Panels Install ng SKYCLOUD types General Frame Step 3 D fferent Types of Panels Motor & L ghts Electr c ty Step 4 Install ng Support Eco Cloud Max Cloud Parts & Caps Step 5 Heat Barr er Water Dra nage Parts...
  • Page 3 Product Sect on V ew Introduct on Eco Cloud Thank you for purchas ng Sunset Pergola Product. Informat on: These nstruct ons nclude helpful h nts and mportant nformat on needed to safely assemble and properly Below the page, you can check the A-A cross-sect on of the SKYCLOUD system and below that B-B cross-sect on.
  • Page 4 L st of Parts L st of Parts Quant ty of parts depend on the project d mens on. Gutter P llar Caps & SC 11 SC 21 P llar Prof le Parts Parts Water SC 12 Gutter Prof le P llar Top Cap Ex t ng Parts...
  • Page 5 L st of Parts L st of Parts Ra l Parts SC 31 Ra l Prof le SC 41 Front F xed Panel S de Ra l Cap M ddle Ra l Cap SC 32 S de Ra l Cap...
  • Page 6 L st of Parts L st of Parts SC 42 SC 43 Ma n Back Panel F xed Panel...
  • Page 7 Step 1.1 Step 1.2 At th s step, you w ll connect P llars w th the Ground surface. At th s stage, mark the locat on for p llar mount ng n the area to be nstalled, tak ng Place p llar prof les SC 11 parallel then connect to base plates...
  • Page 8 Step 1.3 Use Sp r t Level for to be sure every When the project back p llars s close p llars s perpend cular w th ground level. to the wall or any construct on turn back p llars 180º Check system project on and w dht aga n (your project w ll be produced accord ng to th s process).
  • Page 9 Connect each Gutter Prof le SC 21 to p llar prof les SC 11 n the hor zontal d rect on. EXTRA STEP FOR INFORMATION ! If your product cho ce s wall mount SkyFree screws-8x25 hexagon-head bolt and wrench to assembly them safely.
  • Page 10 Assembly left and r ght parts (Ra ls) SC 31 to the SC 11 n the same way. Use spec al screws-8x25 hexagon-head bolt and wrench depend ng on where to nstall. Step 1.5 Step 1.5 8x30 Hexagon-head Bolt...
  • Page 11 Place ra l l ke shown on the p cture and check slope Left Front of the ra ls and d mens on between p llars and compare Left Front Back R ght w th project plan. Front R ght On the last cassete and front casste you w ll see placement of the ra ls.
  • Page 12 Step 1.6 Step 4.2 Back Gutter Concrete Screw Threaded Rod & Buldex 7.5x10 or 12 Torx Somun Concrete Soft Grounds Grounds Front Gutter In th s step check d mens ons aga n D agonal d stance between two p llars must be equal.
  • Page 13 Step 2.1 Step 2.2 Install every panel SC 41 start ng from back. Use Hex Key to complete Move small parts to the cassettes holes. the panel load ng, as shown n the p cture. 5 mm Hex key...
  • Page 14 90º = 90º Wrong True 90º Installat on Installat on Please check th s 3 ma n capt on After nstallat on panel check all carefully. Because th s s mporttan the measurments aga n. for motor and panel rota t ng work ng. F rst of all check the connect on If nstallat on s not made w thout corner po nts.
  • Page 15 Step 2.3 Check every panels After f nal ze panel nterlock ng each other. nstallat on pull out the cassette p ns. And last and f rst panels nterlock ng Th s s mportant f you w ll forget to th s w th f xed f rst and last panels.
  • Page 16 Retracted Length 16.5 Electr c ty Installat on Step Motor Deta ls & 12.2 12.2 Installat on ø8.2 ø8.2 General Features Voltage of motor 24V DC Max mum load 1500N n push / pull Max mum speed at full load 7.9mm/s (w th 1500N n a push or pull cond t on) Stroke...
  • Page 17 Cable Connection for the Single Motor System Cable Connection for the Single Motor System Timotion Motor Motors Main Lineer Control Output Cable Supply Actuator Connection Point (220 V - 50Hz) Depend on your project your system maybe with a single motor or double motor. (Motors already installed inside your gutter, under the cassette parts.) Only need to connect output cables as shown...
  • Page 18 Cable Connection for the Double Motor System Cable Connection for the Double Motor System Motor Motors Timotion Main Timotion Control Output Cable Lineer Supply Lineer Connection Point Actuator (220 V - 50Hz) Actuator SIDE GUTTER BACK GUTTER Electr cal Steps Electr cal Steps...
  • Page 19 PANEL OPENED POSITION PANEL CLOSED POSITION After connecting all motor cables you The maximum panel rotation is can test your panels working. degrees. Your remote control will But the important note is that don’t automatically programmed ready to use. forget to remove PINS.
  • Page 20 LED S ngle Amb ent L ght ng Types & Installat on Plan v ew LED S ngle Amb ent L near LED Mult Amb ent LED RGB Amb ent LED Downl ght Panel Downl ght...
  • Page 21 LED Mult Amb ent LED RGB Amb ent Plan v ew Plan v ew L near L near...
  • Page 22 Panel Downl ght LED Downl ght Plan v ew Plan v ew L neer Downl ght Panel Downl ght...
  • Page 23 Back Project Lighting Project Lighting Plan Plan Rail Install small aparatus first. You can see the SkyCloud plan 3.9x13 screw Use 3.9x13 self drill screws example left side of the page. for installation. Leave 13 mm gap at This is an example with 4 pillars type. the bottom.
  • Page 24 Project Lighting Plan After finishing aparatus, connect Lighting Box on these as shown on the plan. Check placement from plan twice. Back A-1 / A-2 Connect Lighting Box profiles of electricity connection from the corners with using Socket Cables. (like an L) Front Electr cal Steps Electr cal Steps...
  • Page 25 Led Linear Ambient + Downlight (SpotLight) Connections Plan Led Linear Ambient + Downlight (SpotLight) Connections Plan LED Downlight Panels Ambient Receiver Led Driver Main Supply (220 V - 50Hz) When you get your pergola system. LED Ambiance You will see 2 isolated cable. Black 2x0,75 / 3x0,75 / 4x,75 Isolated Cable depens on your lighting system.
  • Page 26 Led Linear RGB + Downlight (SpotLight) Connections Plan Led Linear RGB + Downlight (SpotLight) Connections Plan LED Downlight Panels RGB Receiver Led Driver Main Supply (220 V - 50Hz) When you get your product. LED Linear Ambient You will see 2 isolated cable. Black 2x0,75 / 3x0,75 / 4x,75 Isolated Cable depens on your lighting system.
  • Page 27 Remote controller Types LED lights electrycity and connections For LED lights electrycity and connections; S ngle Mult We are working with a team in our factory who are professional at research and development. Color Color Color So that we are always one step front in world. LED system seperate 6 varieties as below: 1 Single System and single color 4 Multi System and single color...
  • Page 28 Receiver Types Matching Zone operation for MULTI color remote controller S ngle / Mult Color Color Step 1: Turn off the local electricity. Step 2: Press and hold CCT button. Step 3: While pressing CCT button turn on the electricity. Step 4: Press ON button 3 times.
  • Page 29 Matching Zone operation for color remote controller Matching Zone operation for color remote controller CLEAR Step 1: Connection to load to the receiver and power on it. Step 1: Connection to load to the receiver and power on it. (If the receiver was coded before, clear the code first.) (The clearing operation should be finished within 1 minute after the receiver is powered on.
  • Page 30 Step 4.1 Step 4.2 Insert the front Gutter Caps SC 22 Insert the front Gutter Caps SC 22 to the front gutters as shown to the back gutters as shown n the p cture. n the p cture. System System Front Back S de...
  • Page 31 Step 4.3 Step 4.4 Insert the Panel Front Connector SF 41 Insert the Panel Back Connector SF 43 ns de of the Gutter Cap SC 22 as shown ns de of the Gutter Cap SC 22 as shown n the p cture. And make the connect on n the p cture.
  • Page 32 Step 4.5 Step 5.1 Insert Ra l Cap SC 32 prof le At th s step, you w ll top of the Ra l SC 31 M6/20 screw add water ex t ng deta ls. as shown n the p cture. Th s s the small box SC 14 nclude...
  • Page 33 Step 5.2 Step 5.3 At th s step, you w ll add At th s step, you w ll add another water ex t ng deta ls. s l cone sealant to the back Add water dra nage plast c p pe SC 15 as shown s de (place between SC 43...
  • Page 34 Step 5.4 Step 5.5 At th s step, you w ll connect p llars At th s step, you w ll add outs de front SC 12 and upper caps r ng cap SC 17 of the water dra nage system. Use 4.2 x25 Torx screws and Dr ll Install th s part as shown n the p cture and for connect on of the...
  • Page 35 Your SKYCLOUD s ready to use! Advantages of Use SkyCloud s the “B ocl mat c” type In our SkyCloud product, the pergola of the Sky fam ly that has alum num panels that can the ab l ty to move on ts ax s. rotate on the r own ax s between 0 and 135 degrees V a an eng ne that s ntegrated...
  • Page 36 Customer serv ce support@sunsetpergola.com.tr...