Summary of Contents for L2 Microwave BPA00T10W500-1
- Page 1 BPA00T10W500-1 Broadband System User Manual User Manual [BPA00T10W500-1] Please read this manual before using the equipment. And keep this manual with the equipment. E-Mail: sales@l2microwave.com www.l2microwave.com - 1 -...
-
Page 2: Table Of Contents
BPA00T10W500-1 Broadband System User Manual - Contents - GENERAL ..........................3 1.1. Information about this User Manual ........................3 1.2. Purpose of Operation ............................3 1.3. Responsibility of the Operator ..........................4 1.4. Specifications ................................ 5 SAFETY ..........................7 2.1. -
Page 3: General
1.2. Purpose of Operation • The BPA00T10W500-1 is used to amplify electrical input signals with frequencies and powers that meet the limits specified in the technical specifications. • All interfaces are used to connect external devices, the inputs and outputs of which correspond to the requirements of the respective interface specifications provided in the technical specifications, please refer to the data sheet of the BPA00T10W500-1. -
Page 4: Responsibility Of The Operator
BPA00T10W500-1 Broadband System User Manual • RF amplifiers that produce high field strength through radiation antennas for EMC measurements, materials, and device testing in fully shielded chambers. • RF amplifier for energy generation for particle acceleration. • RF amplifiers for feeding magnetic field coils. -
Page 5: Specifications
BPA00T10W500-1 Broadband System User Manual 1.4. Specifications ELECTRICAL SPECIFICATIONS @ 220VAC, 25C, 50 Parameter Symbol Unit Operating Frequency 1000 Output Power @ P , CW Watt Power Gain @ Psat Input Power for Rated P G Gain Flatness @ Rated P ±1.5... - Page 6 BPA00T10W500-1 Broadband System User Manual Input RF drive level without damage +3dBm Over Power @ typ. Psat + 2dB Shut Down Over Current Shutdwon Indication LED Over Temperature 70°C Shutdown Indication LED AMP on / off Push Button Front E-Mail: sales@l2microwave.com www.l2microwave.com...
-
Page 7: Safety
2.1. Basic Safety Instructions Chapter 1 "General" of this manual contains "Basic Safety Instructions" that apply to all products produced and supplied by L2 Microwave. The BPA00T10W500-1 broadband amplifier system and its ancillary equipment must only be operated by qualified technicians. -
Page 8: High Energy Electrical Circuits
2.2.7. Occupational safety from RF shielding The BPA00T10W500-1 broadband amplifier system is shielded from all RF cables, shielding covers and case components to ensure that they are not exposed to RF radiation even if they are close together for extended periods of time. -
Page 9: Rules For Amplifier Services
BPA00T10W500-1 Broadband System User Manual • Use personal protective equipment in the event of smoke formation. Use breathing protection in the danger zone that is independent of the ambient air. 2.2.9. Rules for amplifier services Do not operate the amplifier system (equipment) unless the case is closed. -
Page 10: Installation
Therefore, we recommend installation in a spacious space with no dust or other contaminants. Others The operator of the BPA00T10W500-1 should not be disturbed during operation of the broadband amplifier system. The recommended power of the BPA00T10W500-1 is 3.5kW or more. - Page 11 The minimum required VSWR for the antenna should be used under 2.3: 1. If the operator wants to use it under high VSWR conditions, the amplifier's output can be used at a lower level. The following table shows VSWR condition of Load vs. Output Power of BPA00T10W500-1. Output power...
-
Page 12: Operation Method
BPA00T10W500-1 Broadband System User Manual 4. Operation method This chapter describes the operation and condition of the amplifier. The AMP ON / OFF button on the front panel operates the amplifier and checks the condition of the amplifier. If an error occurs in the amplifier, the Alarm LED on the front panel will change to RED and the amplifier will go off. - Page 13 BPA00T10W500-1 Broadband System User Manual -. Normal operation of the amplifier through “AMP ON / OFF”. It is On mode and it shows that -. Status when there is no problem there is no problem. inside the amplifier -. The condition that can supply RF signal to amplifier.