Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for MultiDyne HUT-APE
-
Page 2: Table Of Contents
Table of Contents Table of Contents ..........................2 Declaration of Conformity ........................3 Safety Info ............................. 4 Overview ............................6 Feature Descriptions ........................7 HUT-BS (CCU Side) ........................13 SilverBack-APE ..........................14 Applications ..........................15 Moving the Fiber Plate ........................16 Panasonic Fiber I/O ........................ -
Page 3: Declaration Of Conformity
Declaration of Conformity... -
Page 4: Safety Info
Safety Info... - Page 5 Laser Safety Information Warning – Use of controls, adjustments, or performance of procedures other than those specified herein may result in hazardous radiation exposure. Warning – Never look directly into the end of the optical fiber while either end of the system is operating. Warning –...
-
Page 6: Overview
ST connectors, and it also tricks the CCU into thinking that your camera is still attached by the hybrid fiber cable. At the cam side of these fibers is the HUT-APE, which takes these two fibers and routes them to a SMPTE hybrid fiber connector. It also plugs into local mains power and injects various DC voltage for your camera into that same SMPTE connector, which now connects to the camera via a much shorter length of hybrid fiber cable. -
Page 7: Feature Descriptions
CCU and use it as a mechanism to electronically switch the output voltage, thereby enabling remote ON/OFF control capability for the connected camera. HUT (LOCAL) – This switch position enables the HUT-APE to switch the output voltage on or off based solely on the sense line control signals from the camera. - Page 8 Fiber I/O. C. Status Indicators HIGH VOLTAGE – This indicator is off when the HUT-APE is in the start-up/standby mode (i.e., low voltage output), lights up green when the camera is connected with its power switch in the ON position, and red if the high voltage is on but the output voltage is lower than the specified operating range.
- Page 9 When a fault is detected in the standby/startup mode (low voltage output), the HUT-APE will prohibit the high voltage output from being enabled. If the system is already in normal operation and a fault occurs, the high voltage will immediately be disabled, and the HUT-APE will protect itself from output short conditions.
- Page 10 This graphic shows the LED display change as the range of optical power, from overload (>0 dBm) to minimum detectable signal (-21 dBm), changes. Optical power greater than 0 dBm will cause all the LEDs to blink red. Optical power less than -21 dBm cannot be read on the meter.
- Page 11 2.2. Rear Panel F. Fiber Plate ® The HUT-APE has multiple fiber I/O options, including ST/UPC, LC/UPC, SC/UPC, or Neutrik ® opticalCon Duo. By default, it is installed on the rear panel from the factory. The fiber port plate can be moved to the front panel to conveniently handle various installation requirements. See Moving the Fiber Plate section for details.
- Page 12 Connect dry (unpowered) fiber cables between the fiber connector(s) on HUT-BS and the "dry" fiber connector(s) on the HUT-APE. HYBRID FIBEROPTIC SMPTE ST 311 CABLE Connect a length of hybrid fiber cables between the HUT-APE and the hybrid connector on the camera / Silverback-APE. PRIMARY AC Use the included AC power cable to connect HUT to AC mains.
-
Page 13: Hut-Bs (Ccu Side)
The Base unit, known as HUT-BS, has a SMPTE hybrid receptacle panel mount connector for connection to the CCU and 2 ST/UPC or duplex LC connectors for the fibers to the HUT-APE. As on the HUT-APE, the ST/LC/SC connectors are labeled FROM CCU and TO CCU. The same considerations concerning the fiber labels should be observed, as on the HUT-APE. -
Page 14: Silverback-Ape
4. SilverBack-APE Future model. -
Page 15: Applications
5. Applications HDTV SMPTE Camera SMPTE Hybrid Cable. Up to 3km HUT-APE Singlemode fiber HUT-BS SMPTE Hybrid Cable Camera Controller Unit (CCU) -
Page 16: Moving The Fiber Plate
6. Moving the Fiber Plate The HUT-APE allows you to have the fiber patched to the front or rear panel to handle different installation requirements. Review the following steps to relocate the fiber plate (ST/UPC shown). All work should be performed in an ESD-safe environment. Use caution not to touch any internal components. - Page 17 5. Remove the four (4) screws holding the blank plate on the other side of the unit. 6. Re-route the internal fibers from their original position to the new fiber plate location. 7. Connect the fibers to the same corresponding ports noted in Step 4. 8.
-
Page 18: Panasonic Fiber I/O
Note: Apply medium strength thread locker on screws before closing the enclosure. Recommended product: Permatex 24010 Medium Strength Thread Locker Blue Gel 1. Unplug the HUT-APE power cable(s) and all connected fibers. Let unit sit for 20 minutes for internal components to discharge. - Page 19 3. Swap both fiber pairs connected in the quad LC coupler. Before (Default) || After (Panasonic) 4. Reinstall top cover.
-
Page 20: Accessories
HUT-APE Rackmount Kit. The optionally available HUT Ears allow up to three (3) HUT-APE units to be mounted into a standard 19” rack. Each HUT-APE takes 2RU height and 1/3rd RU width. (Includes all parts for any of 3 configs shown) - Page 21 Fiber Plate Options HUT-APE-U2-SPP-LC2XXF LC/UPC HUT-APE-U2-SPP-SC2XXF SC/UPC HUT-APE-U2-SPP-ST2XXF ST/UPC HUT-APE-U2-SPP-OC2XXF ® ® Neutrik opticalCON...
-
Page 22: Specifications
9. Specifications 9.1. Unit Dimensions & Weight HUT-APE (W x H x D) 146mm x 88mm x 266mm (5.75 x 3.45 x 10.5 in.), 7.5 lbs HUT-BS (W x H x D) 178mm x 64mm x 51mm (7 x 2.5 x 2 inches), 0.7 lbs... - Page 23 Accuracy 9.3. Power HUT-APE Input 95–250 VAC, 5–2A, 47–63Hz Silverback-APE 325W Grass Valley Camera 300W HUT-APE Power Consumption Sony 180V Cameras 270W (MAX.) Sony 240V Cameras 325W Panasonic Camera 285W HUT-BS (CCU Only) 240 VAC or 375 VDC, 5W max.
- Page 24 HDC-1500 HDC-1700 HDC-2000 HDC-2400 HDC-2500 HDC-2570 ® SONY HDC-3100 HDC-3170 HDC-3500 HDC-4300 HDC-4800 HDC-5500...
-
Page 25: Contact Info
Contact Info Contact support@multidyne.com... -
Page 26: Copyrights
Copyrights “opticalCON” is registered trademarks of NEUTRIK AKTIENGESELLSCHAFT...
Need help?
Do you have a question about the HUT-APE and is the answer not in the manual?
Questions and answers