Vigitron Vi30202U Manual

Vi30202U 24VDC/VAC Coax Ethernet Extender w/60W PoE Manual
The Vi30202U is the perfect solution for replacing existing analog PTZ
cameras with advanced IP PTZ cameras. It uses existing Coax cable for
transmitting IP video up to 5000 feet (1,515 m) and the existing 24VDC or
24VAC power supply as power input to provide up to 60W PoE to the
cameras. Using the existing Coax cable and power supply provides great
time and cost saving.
Its unique Symmetric Bandwidth (SBW™) assures full bandwidth transmis-
sion is maintained over the entire operational distance for both uploads and
downloads with Virtual Zero Packet Loss (VZPL™). Type tested under
NEMA-TS2 environmental standards for extended temperature operations
between -20C° to +65C°. The Vi30202U is MegaPixel Certified (MPC™),
type tested to network packet performance standards, and major manufac-
turer compatibility tested to assure you error free and reliable operations.
Its compact design allows to be installed in many weatherproof and security
houses or many types of camera mounts to further reduce installation costs.
Installation cost savings, proven performance, and major camera brand
compatibility all go into making Vigitron's MaxiiCopper™ Vi30202U an ideal
solution for extended distance data and power transmission.
Important Safety Warning
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer's instructions.
- This installation should be made by a qualified service person and should
conform to all local codes.
- DO NOT bundle UTP or Coax signals in the same conduit as high-voltage
wiring.
- To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron
equipment.
- DO NOT install the unit in a place where the operating ambient tempera
ture exceeds 65°C.
- Make sure that the external power supply output voltage is in the recom
mended range.
- Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus that produce heat.
- Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long
periods of time.
- Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as a power
supply cord or plug is damaged, liquid has been spilled, or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
- The mains plug is used as the disconnect device and shall remain readily
operable.
The Smart Choice for Transmission Solutions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING! - To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture. This apparatus shall not be exposed to
dripping or splashing and no objects filled with liquids, such as vases shall
be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must
be connected to a mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and
shall remain readi y operable.
l
IP Camera-end Installation
- Connect the IP camera RJ45 connector to the 10/100BaseT Ethernet port
of Vi30202U using a standard Cat5/6 cable of maximum 100 m in length.
- Connect one end of the long coax cable to the BNC connector of
Vi30202U.
- Connect a 24VDC or 24VAC power supply, at least 74W, to the Vi30202U
power connector. The power input is a non polarized 2-pin terminal block.
The Power LED, PoE LED and link LED on the 10/100 connector should be
"ON" to indicate proper connection between the camera and Vi30202U.
Ethernet Switch/NVR-end Installation
- Use a Vi24xxA on the receiving side.
- If using a Vi2401A set the Master/Slave dip switch to "Slave" mode and
Set the Remote/Local switch to Local.
- Connect a qualified 12VDC power supply to the Vi24xxA.
- Connect the RJ45 connector of the Ethernet switch to the 10/100BaseT
Ethernet port of Vi2401A using a standard Cat5/6 cable of maximum
100 m in length.
- Connect one end of the long coax cable to the BNC connector of Vi24xxA.
The link LED on the 10/100 Ethernet connector should be "ON" to indicate
proper connection between the switch and Vi24xxA. Also the Traffic LED
on the Coax side should be on and flashing to indicate proper connection.
While the Link LED, Orange for 100BaseT and Green for 10BaseT, in a
steady state will indicate confirmed connection between extenders.
Ethernet Switch/NVR-end Installation
Providing PoE to PTZ Cameras at long distances over Coax
Network Switch
Vi2401A
Data
328 ft. (100m)
Power
Supply
Vi30202U along with Vi2401A can be used to provide data and PoE transmission over lang
distance coax cables.
Ethernet Extenders
Vi30202U
Data
up to 5000 ft. (1523m)
Data + PoE
328 ft. (100m)
www.vigitron.com
Cat 5/6
Coax
PTZ Camera
Vi30202U_UM