Littfinski Daten Technik SA-DEC-4-MM-F Operating Instruction

L D T
ittfinski aten echnik (
Operating Instruction
4-fold switch decoder
from the Digital-Professional-Series !
SA-DEC-4-MM-F
(With possible external power supply)
>> finished module <<
Compatible to Märklin-Motorola-Format:
(e.g. Märklin-Digital∼ [Control Unit, Central Station 1
und 2], Intellibox, EasyControl, ECoS, KeyCom-MM,
DiCoStation, EDiTS, EDiTS pro and others)
For digital control of:
consumers up to 2 Ampere on each output
⇒
(e.g. illumination, disconnection of track sections from
power).
⇒ jammed turnout- and signal drives
(drives with integrated end switch).
This product is not a toy! Not suitable for children under 14 years of age!
The kit contains small parts, which should be kept away from children under 3!
Improper use will imply danger of injuring due to sharp edges and tips! Please store
this instruction carefully.
red point
Multi-Digital
Introduction/Safety instruction:
You have purchased the 4-fold switch decoder SA-DEC-4 for
your model railway as a kit or as finished module.
The SA-DEC-4 is a high quality product that is supplied within
assortment of Littfinski DatenTechnik (LDT).
We wish you having a good time using this product.
The switch decoder SA-DEC-4 of the
Series
can be easily installed and used on your digital railway.
The colored point on the receiver device indicates to which
digital system the decoder can be adapted.
In case the receiver device is marked red the decoder is
suitable for Märklin-Digital~ respectively for Märklin-Motorola
layouts.
In case the receiver device is marked yellow the SA-DEC-4 will
be suitable for the DCC Data format, used for instance at the
systems of Lenz-Digital Plus, Arnold-, Märklin-Digital=,
Intellibox, TWIN-CENTER, Roco-Digital, EasyControl, ECoS,
KeyCom-DC, Digitrax, DiCoStation and Zimo.
The decoder SA-DEC-4 is multi digital and can be installed to
the Intellibox without any problems.
The finished module comes with 24 month warranty.
• Please read the following instructions carefully. Warranty will
expire due to damages caused by disregarding the operating
instructions. LDT will also be not liable for any consequential
damages caused by improper use or installation.
• Also, note that electronic semiconductors are very sensitive to
electrostatic discharges and can be destroyed by them.
Therefore, discharge yourself before touching the modules on
a grounded metal surface (e.g. heater, water pipe or protective
earth connection) or work on a grounded electrostatic
protection mat or with a wrist strap for electrostatic protection.
LDT
)
210312
Part-No.:
Digital-Professional-
Connecting the decoder to your
digital model railway layout:
• Attention: Before starting the installation switch off the
drive voltage by pushing the stop button from the
command station or disconnect the main supply.
The decoder receives the digital information via the clamp KL2.
Connect the clamp with a rail or even better connect the clamp
directly to the command station or to a booster assuring supply
of digital information free from any interference.
Pay attention to the mark at clamp KL2. The color markings
'Black/Schwarz' and 'Red/Rot' next to the clamp are used for
Arnold-Digital (old) and Märklin-Digital=.
Other systems are using the letters 'J' and 'K'.
If you use the decoder for a Märklin-Digital~ respectively
Märklin-Motorola installation please attend to the colors marks
'red/rot' and 'brown/braun'.
The decoder receives the voltage-supply via the two-pole
clamp KL1. The voltage shall be in the range of 12 to 18V~
(alternating voltage output of a model railway transformer) or 15
to 24Volt = (direct voltage output of an insulated power supply
unit).
Now connect the consumers (e.g. illumination, motors or turnout-
and signal coils) to the outputs 1 to 4. The contact marked 'COM'
is the common connection for the bistable relay.
Programming the decoder address:
For programming the decoder address you have to connect a
consumer to the output 1. As it is possible to hear the switching
of the bistable relay the connection of a consumer is not
mandatory.
•
Switch on the power supply of your model rail way.
•
Depress the programming key S1. Do not touch the
integrated circuits of the pc-board because any electrostatic
discharge can destroy the IC`s.
•
The relay connected to output 1 will now switch automatically
every 1.5 seconds. This indicates that the decoder is in the
programming mode.