Advertisement
1.3.7. DO NOT pull or carry the appliance by attached leads.
1.3.8. DO NOT pull plug from socket by the power cable.
1.3.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
Note! This product is double insulated
a) Connect the BROWN live wire to the live terminal ‘L’.
b) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and
that the restraint is tight.
1.4.
BATTERY CHARGER SAFETY INSTRUCTIONS
p WARNING! DO NOT attempt to charge any battery other than that supplied for the drill. Other types of batteries may explode!
3 All mains electrical supply safety features must be followed as described in Section 1.3. above.
3 Disconnect the charger from the mains power supply when not in use.
7 DO NOT expose the charger to damp or wet conditions.
7 DO NOT pull or carry the charger by the power lead.
7 DO NOT operate the charger if it has been dropped, received a sharp knock, or is damaged. Take charger to an authorised agent.
7 DO NOT dismantle the charger as this may cause damage or personal injury and will invalidate your warranty.
7 DO NOT insert foreign objects or material into the hole reserved for the battery pack.
7 DO NOT recharge a second battery pack immediately after charging the first. Consecutive charging will overheat the charger. Allow the unit
to cool for 15 minutes before charging the next pack.
7 DO NOT attempt to connect two chargers together.
3 Store the charger in the same manner as the battery pack, see Section 1.2.
2.
SPECIFICATIONS
Model: CP2440VHK
Chuck size . . . . . . . . . . . . . . . . . . . .13mm
Chuck type . . . . . . . . . . . . . . . . . .Keyless
Motor . . . . . . . . . . . . . . . . . . . . . . . . .24V
Variable speeds . . . . . . . .0-360/0-1100rpm
Max torque . . . . . . . . . . . . . . . .410kgf.cm
Impact rate. . . . . . . . . .0-5760/0-17600bpm
Full charge time . . . . . . . . . . . . . . . .1 hour
Fig. 1
1. Keyless chuck.
2. LCD Battery display.
3. Hammer selector.
4. 10-step torque/hammer control ring.
5. High/low speed switch.
6. Lock, reverse and forward switch.
7. Power switch.
8. 24V battery pack. (two supplied)
9. Battery release button.
10. Handle & depth stop.
3. OPERATING INSTRUCTIONS
Note: When new, the battery pack will have been shipped in a low charge state. It will take longer to charge initially, and several subsequent
charges may also take a little longer, than when the battery pack reaches optimum performance.
3.1.
CHARGING THE BATTERY PACK
3.1.1. To remove the battery pack (fig. 2.A) from the drill, depress the two side release clips (fig.1.9).
WARNING! Do not touch the battery terminals.
p
3.1.2. Place the drill in the carry case and remove the battery charger (fig. 2.B).
3.1.3. The battery pack and charger have the positive (+) and negative (-) terminals
marked. Align the correct terminals and insert the battery (fig. 2). Note: The
battery pack is designed so that it will only enter the charger unit the correct way.
When placed in the charger, a very slight downward pressure will seat the pack
firmly into the power terminals.
3.1.4. Connect the charger to mains power and switch on. The red light (fig. 2.C) will
light indicating that the charge cycle has started.
3.1.5. The red light will remain on until the battery pack is fully charged when it will go
out and the green light (fig. 2.C) will go on. Under normal conditions the battery
will take up to 1 hour to fully charge.
3.1.6. When the green light comes on, switch off the charger, unplug from the mains
and remove the battery pack.
3.1.7. Place the charger in the carry case. Insert the battery pack r
Note: Attempting to recharge a battery pack immediately after use may result in the red charge light not coming on. In such a case allow the
battery to cool for a time and try again.
and therefore requires no earth cable.
LCD battery display.
Press to display
battery charge state.
Blue
Neutral
Wire
FUSE RATING 3 AMP
3
1
fig. 1
4
6
7
9
8
Yellow & Green
Earth Wire
Brown
Live
Wire
Cable
Restraint
2
5
fig. 1
10
fig. 2
CP2440VHK - 1 - 210105
Advertisement
