Hobis MOTION Instruction Manual

HEIGHT-ADJUSTABLE DESK
MOTION
2-segment / 3-segment
INSTRUCTION MANUAL
1.

INTRODUCTION ................................................................................................................................................... 1

2.

PURPOSE, SPECIFICATION AND PRODUCT FUNCTION .................................................................................. 2

3.

RESIDUAL OPERATION RISKS .......................................................................................................................... 3

4.

TECHNICAL DATA ............................................................................................................................................... 3

5.

GENERAL OPERATING INSTRUCTIONS ............................................................................................................ 3

5.1.

Environment for setting the desk ................................................................................................................... 3

5.2.

Setting and connecting the desk to the electrical network .............................................................................. 3

5.2.1.

Desk installation ................................................................................................................................... 3

5.2.2.

Connecting to electrical network ........................................................................................................... 4

5.3.

Safe desk attendance ................................................................................................................................... 4

5.3.1.

Putting into operation ............................................................................................................................ 4

5.4. Instructions For Cleaning And Maintenance ..................................................................................................... 5
5.5. Inspection Period ........................................................................................................................................... 5
6. Legal And Natural Persons ..................................................................................................................... 5
7. Storage ............................................................................................................................................................ 5
8. Transportation ............................................................................................................................................. 5
9. Assembly Manual .......................................................................................................................................... 6
10. POSSIBLE FAILURES AND THEIR REMOVAL ................................................................................................... 7
11. LIQUIDATION OF THE DESK AND ITS COMPONENTS ...................................................................................... 7
12. RELATED AND USED DOCUMENTATION .......................................................................................................... 7
13. THE NAMEPLATE ................................................................................................................................................ 7
Attachment 1 – EC Declaration of conformity by the desk manufacturer ................................................................. 8
Manufacturer: HON – KOVO s.r.o.
Srbská 347 / 2
160 06 Praha 6 – Dejvice
Czech Republic
3
RESIDUAL OPERATION RISKS
3
Clamping, compression Interventions underneath the desk to reduce its height (between the
(feet, hands)
desktop and movable partition in the bottom desk part)
Clamping, pinching Between the movable desk part and firm part of another desk
Electric shock Water leak into the wiring,
power line breakage or damage to insulation, improper connection
to the electrical network
Stumbling
Over a power supply cable laid on the floor
Blow, striking Desk overturning when overloaded, uneven desk loading, poor
desk setting on an uneven floor
Fall from height
Fall off the desk when used in an unallowable way in order to
elevate the working place
Fire and/or explosion Usage in the environment for which the product has not been
intended, motor overload
4
TECHNICAL DATA
Ambient workplace temperature
Workplace relative humidity
Desktop dimensions
Desktop adjustable height range 2-segment
Desktop adjustable height range 3-segment
Total desk weight 2-segment (when assembled)
Total desk weight 3-segment (when assembled)
Desktop allowable load
Vertical adjustment drive
Control and regulation
Electrical network connection
Operating voltage (safety voltage)
Motor input
Engine noise
5
GENERAL OPERATING INSTRUCTIONS
5.1 Environment for setting the desk
The desk can only be used in interior environments.
It is forbidden to use and store this desk outdoors and within areas with a risk of moisture,
water dripping or splashing or effects of other liquids, and within environments containing potentially
flammable or explosive vapours, gases or dust.
There is a risk of electrical shock, explosion and/or fire and damage to the desk and/or its functions.
5.2 Setting and connecting the desk to the electrical network
5.2.1 Desk installation
Before installing and setting the desk, the person appointed has to get acquainted closely and thoroughly with
these instructions and related documentation attached.
Installation of the desk must be carried out according to the enclosed installation instructions.
Cable must be connected to appropriate connectors on the control box in accordance with the installation
instructions.
The desk must be set on a solid and flat floor.
If set between fixed objects – surrounding tables, cabinets or other objects – there must be a gap at least 25 mm
between the desk and respective fixed part to avoid any incidental clamp or squeeze of fingers between the
moving desktop and surrounding objects.
CONTENT
Cause
See chapter 5.3
See chapter 5.3
See chapter 5.1, 5.2
See chapter 5.2
See chapter 5.2
See chapter 5.3
See chapter 5.1
O O
+ 10 C up to + 40 C
70 % max.
1200, 1400, 1600, 1800 x 800 mm
680 mm min., 1180 mm max. (excluding the board)
580 mm min., 1275 mm max. (excluding the board)
32kg (excluding the board)
35kg (excluding the board)
100kg max. (excluding the board)
Electrical, located in the desk frame
Electronically by desktop buttons
Cable and plug into electrical network 230 V, 50 Hz
24 V
80 W
≦ 50db
1
INTRODUCTION
We are very pleased that you have chosen our product, and believe that it will fulfil your expectations. The manufacturer We are very pleased that you have chosen our product, and believe that it will fulfil your expectations. The manufacturer We are very pleased that you have chosen our product, and believe that it will fulfil your expectations. The manufacturer
and R&D department did their best to make the product usable in all the specified conditions and facilitate the work in a and R&D department did their best to make the product usable in all the specified conditions and facilitate the work in a and R&D department did their best to make the product usable in all the specified conditions and facilitate the work in a
wide range of applications. For the product to serve your needs well, before putting into operation we recommend to read f applications. For the product to serve your needs well, before putting into operation we recommend to read f applications. For the product to serve your needs well, before putting into operation we recommend to read
carefully the following chapters to ensure its proper function and safety of the operator as well as to avoid any possible carefully the following chapters to ensure its proper function and safety of the operator as well as to avoid any possible carefully the following chapters to ensure its proper function and safety of the operator as well as to avoid any possible
damage to the device.
Desk operation and its usage are very simple. However, some incorrect manipulations may lead to incidents that can be sk operation and its usage are very simple. However, some incorrect manipulations may lead to incidents that can be sk operation and its usage are very simple. However, some incorrect manipulations may lead to incidents that can be
prevented by proper handling.
Therefore, read these instructions carefully! Therefore, read these instructions carefully!
Particularly important information and warnings are marked with
injury to the operator and/or other persons, and/ or lead to the product damage. injury to the operator and/or other persons, and/
2
PURPOSE, SPECIFICATION AND PRODUCT FUNCT
The height-adjustable desk was designed to increase comfort at work and relieve the physical stress during sedentary adjustable desk was designed to increase comfort at work and relieve the physical stress during sedentary adjustable desk was designed to increase comfort at work and relieve the physical stress during sedentary
work or even when standing up with the option to adjust the best position of its working plane work or even when standing up with the option to adjust the best position of its working plane in the latter case. The work or even when standing up with the option to adjust the best position of its working plane
height-adjustable working plane in combination with height
workplace in order to reduce the spine load and risk of potential injury. workplace in order to reduce the spine load and risk of potential injury.
With such parameters, this product can be used at different sites, mostly in office workpl With such parameters, this product can be used at different sites, mostly in office workplaces on conditions for its use.
Working surface of the desk is made of laminated chipboard
standards and hygienic parameters.
Moving desktop can be adjusted according to the desired working plane height (excluding the board) Moving desktop can be adjusted according to the desired working plane h
range of 680 to 1180 mm (2-segment) or of 580 to 12
Setting the appropriate height is quite simple – just push the control buttons indicating movement directions that Setting the appropriate height is quite simple
are located on the desktop edge.
Desktop movement is powered by an electric motor installed in the desk frame so that its adjustment is very Desktop movement is powered by an electric motor installed in the desk frame so that its adjustment is very Desktop movement is powered by an electric motor installed in the desk frame so that its adjustment is very
comfortable and simple requiring no human power. comfortable and simple requiring no human power.
Figure 1 – Method of the desk operation Method of the desk operation
1/8
5.2.2 Connecting to electrical network onnecting to electrical network
The device can be connected to the power network which has been checked The device can be connected to the power network which has been checked The device can be connected to the power network which has been checked by a competent person.
This connection point must conform to all respective regulations as well as to requirements of the manufacturer. This connection point must conform to all respective regulations as well as to requirements of the manufacturer. This connection point must conform to all respective regulations as well as to requirements of the manufacturer.
Measure
It is necessary to protect the supply cable from any mechanical damage. The cable must be laid so that it It is necessary to protect the supply cable from any mechanical damage. The cable must be laid so that it It is necessary to protect the supply cable from any mechanical damage. The cable must be laid so that it
does not prevent a safe movement of persons. Stumbling over an unsecured cable just laid on the floor
and/or its pulling from the socket or desk must be avoided. and/or its pulling from the socket or desk must be avoided.
Control unit is provided with protection against power fluctuation. Even so, it is recommended to use Control unit is provided with protection against power fluctuation. Even so, it is recommended to use Control unit is provided with protection against power fluctuation. Even so, it is recommended to use
surge sockets to connect the desk to the electrical network.
5.3 Safe desk attendance
5.3.1 Putting into operation Putting into operation
Operation of the table must be over 18 years old Operation of the table must be over 18 years old.
Before using the product, the desk operator must get familiar with instructions to operate its functions. Before using the product, the desk operator must get familiar with instructions to operate its functions. Before using the product, the desk operator must get familiar with instructions to operate its functions.
Before the first switching-on and after each disconnection from the network supply, the desk must be
initialized.
Initialization (adjustment of the starting position for any further desired height adjustment).
Press the button indicating the movement downwards (retraction). The desktop moves down into the starting Press the button indicating the movement downwards (retraction). The desktop moves down into the starting Press the button indicating the movement downwards (retraction). The desktop moves down into the starting
position – keep on pressing the button for at least keep on pressing the button for at least 5 seconds. It is necessary to per
some cases.
When lifting or lowering the desktop, When lifting or lowering the desktop, its free movement must not be prevented in any way by pushing the
desktop in both vertical directions (up or down)!!! Such action could damage the engine desktop in both vertical directions (up or down)!!!
When adjusting its height, the desk can be burdened up to the maximum load capacity of When adjusting its height, the desk can be burdened up to the maximum load capacity of When adjusting its height, the desk can be burdened up to the maximum load capacity of 100 kg (excluding the
board)
WARNING !!! MOVEMENT AND
Duty cycle (engine run in both movement directions) can be only 10% of the cycle time. Duty cycle (engine run in both movement directions) can be only
(The maximum duration of continuous movement when adjusting the desk height equals 2 minutes. After this (The maximum duration of continuous movement when adjusting the desk height equals 2 minutes. After this (The maximum duration of continuous movement when adjusting the desk height equals 2 minutes. After this
period, the desk must be resting for at least 18 minutes period, the desk must be resting for at least 18 minutes – cannot be used!) Otherwise, you risk a permanent
damage to the engine!!!!!
If the desktop is in movement, it is prohibited to intervene into the space underneath with hands or feet, If the desktop is in movement, it is prohibited to intervene into the space underneath with hands or feet, If the desktop is in movement, it is prohibited to intervene into the space underneath with hands or feet, especially
in the section between the movable desktop and fixed lateral connection. in the section between the movable desktop and fixed lateral connection.
When connecting office equipment such as PC, monitors, lamps, etc. As the table may be pulling the load wires When connecting office equipment such as PC, moni
and cut leading to damage them. Ensure adequate length of conductors and their appropriate location. and cut leading to damage them. Ensure adequate length of conductors and their appropriate location. and cut leading to damage them. Ensure adequate length of conductors and their appropriate location.
The smallest gap between the fixed lateral connection
495 mm (3-segment).
There is a risk of accident by squeezing hands or feet. There is a risk of accident by squeezing hands or feet.
When the desktop moves (up or down), other persons (e.g. colleagues, children, etc.) When the desktop moves (up or down), other persons (e.g. colleagues, children, etc.) must not occur on or under When the desktop moves (up or down), other persons (e.g. colleagues, children, etc.)
the desk and within its proximity. There is a risk o
There must be no objects or pieces of furniture higher than 595
the desk to prevent their damage, or damage of the desk when the desktop moves downwards!!! the desk to prevent their damage, or damage of the desk when the desktop moves downwards!!! the desk to prevent their damage, or damage of the desk when the desktop moves downwards!!!
It is prohibited to use the desk for performing activities for which it has not been designed – elevating the working It is prohibited to use the desk for performing activities for which it has not been designed It is prohibited to use the desk for performing activities for which it has not been designed
place when executing repairs and maintenance or for other purposes out of its intention. place when executing repairs and maintenance or for other purposes out of its intention. place when executing repairs and maintenance or for other purposes out of its intention.
3/8
and warnings are marked with symbols. Their nonobservance may cause
ON AND PRODUCT FUNCTION
rking plane in combination with height-adjustable chair meet ergonomic requirements for the adjustable chair meet ergonomic requirements for the
laminated chipboard – it is harmless and hygienic and meets all the relevant it is harmless and hygienic and meets all the relevant
segment) or of 580 to 1275 mm (3-segment).
just push the control buttons indicating movement directions that
ent a safe movement of persons. Stumbling over an unsecured cable just laid on the floor ent a safe movement of persons. Stumbling over an unsecured cable just laid on the floor
sockets to connect the desk to the electrical network.
LET'S PREVENT INJURIES AND ACCIDENTS!! LET'S PREVENT INJURI ES AND ACCIDENTS!!
on and after each disconnection from the network supply, the desk must be on and after each disconnection from the network supply, the desk must be
e starting position for any further desired height adjustment). e starting position for any further desired height adjustment).
its free movement must not be prevented in any way by pushing the
Such action could damage the engine!!!
CONTINUOUS RUN OF THE ENGINE STROKE IS L
10% of the cycle time.
cannot be used!) Otherwise, you risk a permanent
tors, lamps, etc. As the table may be pulling the load wires
fixed lateral connection and movable desk part is 59 and movable desk part is 595 mm (2-segment) or
There is a risk of accident by squeezing or compressing. f accident by squeezing or compressing.
eces of furniture higher than 595 mm (2-segment) or 495 mm (3
. Their nonobservance may cause
aces on conditions for its use.
(excluding the board) within the
2/8
It is necessary to perform this operation twice in
E ENGINE STROKE IS LIMITED !!!
segment) or 495 mm (3-segment) under
4/8