Related Manuals for FLEET Kombi Classic
Summary of Contents for FLEET Kombi Classic
- Page 1 User Manual Fleet (Line Markers) Limited, Fleet House, Spring Lane, Malvern, Worcestershire, WR14 1AT Tel: 01684 573535 sales@flmuk.com www.fleetlinemarkers.co.uk...
- Page 2 Markers) Limited. Founded in the 1950’s Fleet are regarded as the world’s leading expert in the field of line marking. Of course its not just the machines that Fleet are famous for, our range of line marking paints are used around the world, wherever the pitch, whatever the occasion.
- Page 3 ASSEMBLING YOUR KOMBI CLASSIC MARKER PREPARING FOR USE 1. Carefully remove the machine and accessories from packaging. 2. Insert handlebar section; adjust to suit user’s height and tighten us- ing thumb screws. 3. Bar ends can be adjusted to suit hand position using the supplied 5mm allen key.
- Page 4 KNIB AND NOZZLE ASSEMBLY The Knib and nozzle assembly is located inside the paint tank of the ma- chine and requires some assembly before use. Refer to the diagram below and follow these steps. 1. Remove packaging from tank. 2. Place arms (A) & (B) over the pivot bar (C) 3.
- Page 5 The knib and nozzle assembly can be fitted to the central post at the front of the machine or to either side of the front axle. Front mounted knib and nozzle assembly 1. Fit the knib and nozzle assembly onto the tapered stem at the front of the machine.
- Page 6 Side Mounting your Knib 1. Remove the R clip from the required side of the knib. (Fig 5) 2. Fit the pivot bar of the knib over the axle and align the holes. Refit the R clup to secure the knib to the axle. 3.
- Page 7 A. Fill the paint tank with water to correct dilution rate, tank markings are provided as a guide. B. Fill the paint tank with the selected Fleet paint and refit the lid. Note: always pour water in first followed by Fleet paint.
- Page 8 Flow return tap The Kombi Classic line marker is fitted with a flow return tap, this can be used for mixing concentrates and bleeding air from the system. To operate the flow return system, proceed as follows: 1. Ensure the paint/water changeover valve is in the ‘paint’ position (lever pointing forward) (Fig 11) 2.
- Page 9 Setting the line width The line width is determined by the width between the guide discs and the nozzle height. Both must be adjusted correctly to obtain a good line with the optimum paint usage. A ruler is located in the nozzle post for measuring the line width and the nozzle height.
- Page 10 If necessary adjust the nozzle height. Turn off the pump (Fig 14) 4. Close the bonnet. Ensure the blue coiled hose is arranged with no kinks and is not fouling on the guide discs. The Kombi Classic line marker is now ready for line marking.
- Page 11 LINE MARKING WITH YOUR KOMBI CLASSIC LINE MARKER Marking a line 1. Ensure there is correctly mixed product in the paint tank. 2. Ensure the battery is fully charged 3. Paint/water valve is in the ‘paint’ position (lever pointing forward) 4.
- Page 12 FLUSHING AND CLEANING IMPORTANT: When cleaning./flushing the Kombi Classic line marker, ensure that water courses are not contaminated with paint. If in doubt, check with the local authority. Quick flush (daily) This can be used before breaks in operation or at the end of a line marking day.
- Page 13 Full System flush (weekly) It is not recommended to store paint in the machine for longer than 24hrs Ensure that the water tank has sufficient water for the cleaning operation. Position the machine where it can be flushed and cleaned. With the paint/water tap in the ‘water’...
- Page 14 The cleaner can be used with a wide variety of Fleet machine parts including nozzles, filters, pipework and couplings, returning them to an almost new condition without any damage.
- Page 15 2. Using the spring collars, slide the line guide discs in, so that they support the nozzle assembly centrally. 3. Loosen knib retainer clip and lift the knib from the tapered post. 4. Park the knib onto the bonnet horn. 5. The Kombi Classic line marker is now ready for transportation and/or storage.
- Page 16 TROUBLESHOOTING If the Kombi Classic line marker is not producing the perfect line, the table below is to help diagnose and remedy simple issues. The main cause for failure is inadequate cleaning/flushing. It is imperative to keep the paint system free from dried paint particles.
- Page 17 Quick Connectors Removal 1. To release a pipe from a quick connector, push on both sides of the blue collar. 2. With the collar oushed in, pull the pipe from the connector. Replacement 1. To replace a pipe into a quick connector, simply push in the pipe. The pipe should be inserted 15mm to ensure a good connection.
- Page 18 Diagrams UNIVCOMP9038 UNIVCOMP9013 KOMBCOMP1028 KOMBCONS1003 UNIVCOMP9009 UNIVCONS9058 KOMBCOMP1029 KOMBCOMP1106 PART NO PART NAME KOMBCOMP1028 Handle Bar Top Section KOMBCOMP1029 Handle Bar Bottom Section KOMBCOMP1106 Steel P Clip 22mm KOMBCONS1003 M6 x 25 Socket Cap Head Screw UNIVCOMP9009 M6 Thumb Screw UNIVCOMP9013 Rubber Handle Grips UNIVCOMP9038...
- Page 19 KOMBCOMP1026 KI00COMP5058 KOMBCOMP1027 KICOCOMP6017 KOMBCOMP1033 KOMBCOMP1037 KOMBCOMP1233 KOMBCOMP1036 KOMBCONS1017 UNIVCOMP5555 PART NO PART NAME UNIVCOMP5555 Wheel & Solid foam tyre KI00COMP5058 Bonnet Hinge (Sprung) KICOCOMP6017 Bonnet Horn KOMBCOMP1233 Tapered Stem KOMBCOMP1026 Tank Lid KOMCOMP1027 Tank Filter KOMCOMP1033 Bonnet KOMBCOMP1036 Plastic Drain Cap KOMBCOMP1037 2 Inch vented water cap KOMBCONS1017...
- Page 20 KOMBCOMP1031 UNIVCOMP9005 KIC00COMP5098 UNIVCOMP9056 KI00COMP5071 UNIVCOMP8521 UNIVCOMP9115 KOMBCOMP1041 UNIVCOMP1055 UNIVCOMP9113 KOMBCOMP1046 UNIVCOMP9112 UNIVCOMP9114 PART NO PART NAME KI00COMP5071 Y Shaped Connector 8mm UNIVCOMP8521 Bowl Filter Complete KI00COMP5098 Push Fit Hand Valve KOMBCOMP1046 1/4 BSP Male Thread Female Coupler KOMBCOMP1031 Tank Filter UNIVCOMP8522 8mm x 6mm P/Mount Quick Release Bulkhead UNIVCOMP1055...
- Page 21 KOMBCOMP1039 KOMBCOMP1022 KOMBCOMP1229 UNIVCONS9067 UNIVCONS9058 UNIVFINPUMP5 KOMBCOMP1226 UNIVCONS9058 UNIVCONS9106 PART NO PART NAME KOMBCOMP1022 Complete Operating Switch KOMBCOMP1023 Coiled Mains Cable KOMBCOMP1039 SLA Battery KOMBCOMP1230 UK Charger (not shown) UNIVFINPUMP5 Diaphragm Pump KOMBCOMP1226 Charge Socket UNIVCONS9058 M6 x 20 Flat Repair Washer UNIVCONS9067 M6 SS Hex Nyloc Nut UNIVCONS9106...
- Page 22 KI00COMP1195 KI00COMP5044 UNI- KOMBCOMP1210 UNIVCOMP9007 KOMBCOMP1196 KI00COMP1198 UNIVCOMP8541 KOMBCONS1004 KOMBCOMP1020 KOMBCONS1015 KOMBCONS1013 KI00COMP5041 KI00COMP5040 UNIVFINP1000 UNIVCOMP5040 UNIVCOMP5037 KOMBCOMP1051 PART NO PART NAME UNIVCOMP5037 Guide Disc Enclosed Bearing KI00COMP5040 Spring Collar KI00COMP5041 Metal Guide Arms Set (Left & Right) KI00COMP5044 Ruler Assembly KI00CONS7012 M5 Hex Full Nut KOMBCOMP1020...
- Page 23 Specification Machine Length: 127cm Width: 74cm Height: 109cm Net Weight: 27kg 127cm 74cm Package Length: 77cm Width: 64cm Height: 57cm Net Weight: 29kg...
- Page 24 The Kombi is not guaranteed against normal wear and tear This guarantee does not interfere with the customer’s statutory rights. The pump is guaranteed for 12 months when using Fleet paint. Machine must be registered by filling in the warranty card Please fill out the table below for quick reference should you require.