Table of Contents
Advertisement
Quick Links
General importer for
The joy of washing
bottles
Industrial washing machines
e
ba
tec
ric
umgartner
hnik
-
industrial rinsing
Operating Instructions
Push through bottle rinsing machine
GS 81
Edition: November 2020
Erich Baumgartner
Gastronomiemaschinengroßhandel
Hauptstrasse 4 A - 5222 Munderfing
Tel.: 0043 / (0)664 / 1816518
e-mail: verkauf@gastrohandel.at
www.flaschenwaschen.com
Advertisement
Table of Contents
Summary of Contents for ebatec GS 81
- Page 1 The joy of washing bottles Industrial washing machines umgartner hnik industrial rinsing Operating Instructions Push through bottle rinsing machine GS 81 Edition: November 2020 Erich Baumgartner Gastronomiemaschinengroßhandel Hauptstrasse 4 A - 5222 Munderfing Tel.: 0043 / (0)664 / 1816518 e-mail: verkauf@gastrohandel.at www.flaschenwaschen.com...
-
Page 2: Table Of Contents
Contents Panel Page Instructions for the fitter Page Commissioning by the customer Page Preparation for rinsing Page Rinsing Page Care cleaning decalcification Page Technical data Page Possible Troubleshooting Page Wiring diagram Page 10 - 12 Assembling the bottle basket Page 13 - 17 Page 2... -
Page 3: Panel
Panel Main switch Indicator light Indicator light Incl. lamp Temperature Rinsing cycle (No 2) (No. 1) (No 3) Instructions for the fitter / installer The machine is equipped with the following accessories: Power supply 5 x 4 mm² connected to the rinsing machine, supply hose with the matching connectors and joints, drain hose. -
Page 4: Commissioning By The Customer
Connect the water supply hose to the external thread at the installation site. The water supply hose is already connected to the inlet valve of the water inlet at the front of the machine. Connect the water supply hose to the external thread at the installation site. The drain hose is already mounted to the machine. -
Page 5: Preparation For Rinsing
Preparation for rinsing Depending on the items to be rinsed, it is necessary to insert the corresponding rinsing arms. Rinsing arms for the Rinsing arms for Withdraw the rinsing rinsing of yoghurt jars, bottle rinsing arm from the bracket work utensils, crates or and pull it out of the buckets, etc. -
Page 6: Rinsing
Rinsing Open the hood and check if the fine filter, the surface filter as well as the overflow pipe are in the correct position. Fold down the flushing arm and insert the basket skid. Close the hood and press the main switch (No. 1). Then, the machine starts spraying the fresh water into the interior and at the same time the liquid cleaning agent will be supplied. -
Page 7: Care Cleaning Decalcification
Care cleaning decalcification In order to ensure a good maintenance of the machine, it is necessary to ensure the following: Switch off the main switch. Empty the machine every day, pull out the overflow pipe and clean the strainer as well as the fine sieve. -
Page 8: Technical Data
Technical data: WEEE-Reg.No.: DE 51131709 Hourly output about 250 bottles/h Rinsing time: 4 min 50 sec. Bottles per rinsing process: max. 20 pcs Pump capacity: 1500 W Circulation rate: 550 ltr./min. Tank heater: 2 x 4500 W Overall connected load: 10600 W Voltage: 400 Volt... -
Page 9: Possible Troubleshooting
Possible Troubleshooting Malfunction Possible cause / Remedy It is not possible to switch on the The power supply to the machine is machine interrupted, cause within the machine., Contact the after-sales service The machine is not being filled with The check valve provided by the water customer is closed, the air trap is soiled –... -
Page 10: Wiring Diagram
Seite 10... - Page 11 Seite 11...
- Page 12 Electric diagram Rinsing machine mod. GS-81 ECO Switch Commissioning Switch drain pump (optional) Micro magnet of the hood Contact protection tank heating element (A) Contact protection tank heating element Contact protection rinsing motor Relay micro magnet hood Relay flushing pump (optional) Relay drain pump (optional) Program switch slow motor Pressure pump flushing (optional)
- Page 13 Bottle Basket The system of our bottle basket of the GS 81 can be used for milk or cream bottles with an opening diameter of at least 38 mm. Scope of delivery: pcs basic basket pcs support rails 36 pcs support rails...
-
Page 14: Assembling The Bottle Basket
Assembly of the bottle basket Put the template on the table and put the bottle basket over the template. Attention: The template is marked with the word FRONT one position. Also mark the basket with a cable tie or the like. The basket is square but it only has one correct front. - Page 15 Also check how many bottles can be used in the bottle basket depending on the type or size of the bottle. Also, the number of the support bars to be mounted would change depending on the number of bottles. Place the support bars on the bottom level of the support rails.
- Page 16 When using a cordless screwdriver, it is recommended, not to use the maximum torque output of the cordless screwdriver. As soon as the bottom level of the bottle basket is assembled, you can assemble the upper level of the bottle basket.
- Page 17 When placing the milk bottles of 1.0 l into the machine, always first put the rear bottle into the basket. Then put the other 4 bottles in the row. Page 17...