LG 42PM4M Owner's Manual page 33

Set ID
Set ID
- Use this function to specify a monitor ID number.
- Refer to 'Real Data Mapping 1'. See page 35.
PICTURE0
Language
Child lock
SOUND0
ISM Method
TIME0
Set ID
SPECIAL
G G
Tile mode
SCREEN0
Low power
Demo
Menu
Prev.
1. Press the MENU button and then use the
2. Press the G G button and then use
3. Press the button and then use
G G
• The adjustment range of
Communication Parameters Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
Command Reference List
Command Reference List
COMMAND 1 COMMAND 2
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Colour
10. Tint
11. Sharpness
12. OSD Select
13. Remote Lock /Key Lock k
14. Balance
15. Colour Temperature
16. Abnormal state
17. ISM mode
18. Auto Configure
19. Key
20. Tile Mode
21. Tile H Size
22. Tile V Size
23. Tile ID Set
24. Natural Mode (In Tile mode)d
button to select the
D D / E E
button to select
D D / E E
button to adjust
F / G
is 1 ~ 99.
• Stop bit : 1 bit
• Communication code : ASCII code
• Use a straight cable.
DATA
(Hexadecimal)
k a 0 ~ 1
k b 2 ~ 9
k c 1 ~ 9
k d 0 ~ 1
k e 0 ~ 1
k f 0 ~ 64
k g 0 ~ 64
k h 0 ~ 64
k i 0 ~ 64
k j 0 ~ 64
k k 0 ~ 64
k l 0 ~ 1
m 0 ~ 1
k t 0 ~ 64
k u 0 ~ 3
k z FF
j p 0 ~ 8
j u 1
m c Key Code
d d 0 ~ 44
d g 0 ~ 64
d h 0 ~ 64
d i 0 ~ 10
j 0 ~ 1
PICTURE0
Language
Child lock
SOUND0
ISM Method
TIME0
Set ID
SPECIAL0
Tile mode
SCREEN0
Low power
Demo
Menu Prev.
menu.
.
to choose the desired monitor ID number.
T ransmission / Receiving Protocol
T ransmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: k, j, m,d
* [Command 2]: To control Plasma Monitor set.
* [Set ID]: You can adjust the set ID to choose desired moni-
tor ID number in Special menu. Adjustment range
is 1 ~ 99. When selecting Set ID '0', every con-
nected Plasma Monitor set is controlled. Set ID is
indicated as decimal (1~99) on menu and as
Hexa decimal (0x0~0x63) on transmission/receiv-
ing protocol.
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
* [Cr]: Carriage Return
ASCII code '0x0D'
* [ ]: ASCII code 'space (0x20)'
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* * If there is error, it returns NG
External Control Device Setup
G G
1
Owner's Manual 33