Summary of Contents for C-Com iNetVu 7000 Series
- Page 1 Viasat SurfBeam® 2 Auto Acquire and the iNetVu® 7000 Series Controller ViaSat SurfBeam® 2 (Auto Acquire) 1-877-iNetVu6 www.c-comsat.com Revision 3.1 October 15, 2015...
- Page 2 INETVU® MOBILE SYSTEM QUICK START – VIASAT AUTO-ACQUIRE This page is intentionally left blank. C-COM Satellite Systems Inc. Page 2...
-
Page 3: Pre-Configuration Check List
This can be acquired by login to modem webpage at 192.168.100.1. Go to Modem icon, the information can be found under INDENTIFICATION section. Note: Please contact C-COM if you require more information about modem compatibility as these may change without further notice. - Page 4 1. USB Interface System Wiring Diagram for SurfBeam® 2 (Mobile) ® *Recommended for proper grounding of iNetVu systems. Note: TX cable is connected directly to the modem and RX cable NOT used with SurfBeam® 2 (Auto Acquire). C-COM Satellite Systems Inc. Page 4...
- Page 5 2. Network Interface System Wiring Diagram for Viasat SurfBeam® 2 (Mobile) ® *Recommended for proper grounding of iNetVu systems. Note: TX cable is connected directly to the modem and RX cable is NOT used with SurfBeam® 2 (Auto Acquire). C-COM Satellite Systems Inc. Page 5...
- Page 6 7000 Front Panel USB drivers must be installed for USB connection method. The configuration process is only required to be done once as long there are no change in satellite, service, modem, or platform parameters. C-COM Satellite Systems Inc. Page 6...
-
Page 7: Tips And Recommendations
Override Compass can be selected without selecting Full Search but this does not hold true for the vice-versa. Refer to Controller User Manual for more information on using the iNetVu Controller and options associated with your system. C-COM Satellite Systems Inc. Page 7... - Page 8 192.168.100.4 Subnet Mask: 255.255.255.0 Gateway: 192.168.100.1 The Gateway is usually the Router IP address. If no router is used, it is usually the VSAT Modem IP Address. Set the DNS IP Addresses if required. C-COM Satellite Systems Inc. Page 8...
- Page 9 ‘↑’ button to select “Y” (yes) and press “Enter”. d. Click the “reset” button on the controller. You may view the 7000 Controller IP from the LCD interface via – MONITOR IP (C_IP) C-COM Satellite Systems Inc. Page 9...
-
Page 10: Software Installation And Configuration
Please Note: Do not connect the Controller via USB until the drivers and software have been installed 1. If you are installing from the USB flash drive or have downloaded from the C-COM FTP/KB, run the iNetVu7000Setup.exe file. 2. Install the iNetVu 7000 Software and close when complete. - Page 11 INETVU® MOBILE SYSTEM QUICK START – VIASAT AUTO-ACQUIRE 3. Install the FTDI USB Drivers and iNetVu USB Drivers. Both are required. Click “Extract” Click “Next” Click “Finish” 4. Continue through the USB Driver Installation Wizard. Click “Next” Click “Finish” C-COM Satellite Systems Inc. Page 11...
- Page 12 Select “Install the software automatically” Click “Continue Anyway” Click “Finish” 7. Windows Vista and 7 users, the drivers should install automatically without any further user action. 8. You have successfully installed the 7000 iNetVu Drivers and Software. C-COM Satellite Systems Inc. Page 12...
- Page 13 Please select “Do not show this message again” so this pop-up will not appear after you have completed the initial Controller setup. 2. If the controller firmware does not match you will be prompted to update. C-COM Satellite Systems Inc. Page 13...
- Page 14 4. You may wish to continue through the wizard to complete the controller configuration or verify the settings. You can switch to the iNetVu software at any time by right clicking and selecting Controls. C-COM Satellite Systems Inc. Page 14...
- Page 15 5. Configure the Platform Type, Version and Serial No. If no changes are needed press “Next” to continue. Platform Type: Antenna Model Version: Antenna Version Serial No: Antenna Serial Number It is important that this information be correct or will result in undesired antenna behavior. C-COM Satellite Systems Inc. Page 15...
- Page 16 HTTP (how the Controller will communicate with the Modem) Modem Configuration IP Address: Enter the Modem IP Address Controller TCP/IP Settings IP Address: Controller IP Address Subnet Mask: Controller Subnet Mask Default Gateway: Controller Gateway (Modem or Router) C-COM Satellite Systems Inc. Page 16...
- Page 17 Using Software/Firmware Ver. 7.5.7+ the controller will receive the target angles from the SurfBeam® 2 Auto Acquire modem for both the 111.1 and 115.1 Satellite Longitude. No changes are needed. Please click Finish to complete the setup. C-COM Satellite Systems Inc. Page 17...
- Page 18 9. Congratulations you have configured your iNetVu Controller. You can now find satellite by pressing the FIND SAT button from the front panel or by launching the iNetvu Software. *For more detailed information on the iNetVu® 7000 Controller Software, refer to the iNetVu® 7000 Controller Manual C-COM Satellite Systems Inc. Page 18...