Related Manuals for MAXPEEDINGRODS MXR-3M
Summary of Contents for MAXPEEDINGRODS MXR-3M
- Page 1 Since 2006 Since 2006 Fuel Heater +1 213 459 3517 COOP@MAXPEEDINGRODS.COM WWW.MAXPEEDINGRODS.COM...
-
Page 2: Table Of Contents
Table of Contents Introduction Installation Notes Attention Technical Parameters • Information on the devices and accessories included in this Heater Structure manual is provided for reference only; actual products are subject to change without prior notice. Installation • After opening the product's packaging box for the first time, Usage please ensure that the main device and spare parts are included in the packing list. - Page 3 Hot air outlet tubing ø 76 mm × 500 mm piece Mounting plate piece T connector piece Exhaust silencer piece Model : MXR-3M Fuel tank piece Exhaust silencer piece Repair tool piece Oil extractor piece Fuel hose 3.5m piece...
-
Page 4: Introduction
In this way, a vehicle’s cab or passenger compartment can be heated whether or not the engine is running.A schematic diagram Model : MXR-3M Fig. 1 is shown in Fig. 1 PARKING AIR HEATER... -
Page 5: Installation Notes
1.4 Unsuitable Situations and Places The heater must not be used in the following situations and places： For constant heating in enclosed spaces (to avoid risk of poisoning), such as : INSTALLATION NOTES Residential rooms Garages Work huts, weekend Houseboats, etc. homes and hunting huts For directly heating and drying (to avoid danger/damage) : CAUTION... -
Page 6: Technical Parameters
– The hot air pipes within the vehicle must be arranged or protected Failure to comply with this technical data Model (Split style) MXR-3M from the vehicle’s passenger compartment. such that they do not create risk of injury or damage through being can result in malfunction. -
Page 7: Heater Structure 1
Overheating Sensor Temperature Sensor This temperature sensor is installed on the outer wall in Located into the LCD controller, the temperature the middle of the heater body. If the shell temperature sensor measures the ambient temperature at the air exceeds 270°C, fault code E-5 is reported, and the inlet and provides the data for the mainboard which, heater will shut down. -
Page 8: Installation
Only the components provided can be used for installation of the heater. Install in accordance with Fig.5 , the installation diagram, below: INSTALLATION 1. Main Device 12. Inlet Air Pipe Clamp 2. Main Harness 13. Inlet Air Pipe Clip 3. Fuse Block 14. - Page 9 Installation position: Installation position: Model MXR-2Y & MXR-3M（All-in-one style）have two power supply methods: car battery and DC 12V(AC/DC Fig.6 adaptor optional)，pls refer Only one power supply method can be used at a time, CANNOT be used at the same time.
- Page 10 5.1.2 Space requirements 5.1.3 Sealing Adequate space for installation and maintenance must be provided. For installation space requirements, please refer to Fig. 12 A good seal between the main device and the vehicle mounting surface is necessary. A flange gasket (shown in Fig.11 .
- Page 11 5.1.4 Mounting plate 5.1.5 Installation orientation 5.1.6 Check the fan wheel 5.2.2 Temperature resistance A mounting plate is needed if the thickness of the -Install the heater on the vehicle floor is preferred as After the installation, ensure that there is no contact or If an external heating air pipe is attached to Fig.
- Page 12 5.3 Installation of Fuel Supply System 5.3.3 Fuel line A sharp knife must be used to cut fuel hoses and pipes 5.3.1 Fuel pump 5.3.2 Pressure height of fuel pump to length. Their Interfaces must not be crushed and 90° The fuel pump shall be mounted in a protective rubber The difference in elevation between the level of the fuel must be free of burrs.
- Page 13 5.4 Installation of Electrical Components 5.5 Installation of Combustion Air System 5.4.1 Main wire harness 5.4.2 Battery connection The connection diagram for the main wire harness and Connect the RED wire on the fuse box to the PLUS - Air for combustion must be fresh air sucked in from outside the vehicle; fumes from combustion must be discharged to outside the Fig.19 heater as .
-
Page 14: Usage
5.5.4 High temperature exhaust pipe CAUTION When the heater is running, the surface of the exhaust Risk of injuries and burns! pipe will reach a high temperature. Ensure that this pipe All types of combustion produce high temperatures is installed far away from plastic components or other and toxic exhaust fumes;... - Page 15 6.2 Electrical Parameters Electrical Connection Diagram 6.1.2 Bluetooth App control (optional) Bluetooth RF Characteristics : Electrical data table - BLE 4.2 Pump - RF data rates up to 2Mbps Parameter name Specification - TX Transmit Power: +10dBm - RX Receive sensitivity: -94.5dBm@BLE Switch Blower 1Mbps...
- Page 16 6.3 LCD Panel Switch Functions 6.3.4 Power mode operation 6.3.6 Setting time 6.3.1 Manual pump operation (Pump_oil) Settings cannot be adjusted until the startup process is Long press the " " key to enter power mode/temperature mode, Press the " "...
- Page 17 Voltage setting 6.3.7 Settings menus 6.3.8 Bluetooth pairing (optional) Enter the voltage setting mode; the system will In the shut-down state, long press the " " key to enter Blue-tooth pairing display U-12v or U-24V. (This has been set before the menu interface, then press"...
-
Page 18: Troubleshooting
7.2 Fault Codes In case of a fault, a fault code and corresponding faulty component icon will flash on the LCD panel. Please refer to the following fault code and solutions table to resolve the problem. A flashing glow plug, oil pump, fan, sensor, or power supply icon indicates a fault in the corresponding device. TROUBLESHOOTING Fault code Cause of failure... -
Page 19: Precautions
Fault code Cause of failure Solutions 1.confirm that the fan wheel is not stuck; 2.confirm that the connector is plugged in securely; Fan motor fault 3.confirm that gap between the wheel magnet and controller’s Hall sensor is not excessive; 4.confirm that the power line is not in a short-circuit or open-circuit state; 5.Electric leakage. - Page 20 After switching to low-temperature fuel, run the heater damage to the heater due to its unauthorized Modell MXR-3M for at least 15 minutes to allow the new fuel to fill the fuel disassembly, or caused by installation or operation in line and fuel pump.
- Page 21 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the MXR-3M and is the answer not in the manual?
Questions and answers