Summary of Contents for Parkmatic PRO OES
- Page 1 PRO OES Front-Rear Parking Sensor Installation Manual PRO22218 (Buzzer) PRO43218 (LCD) 10R-05 1524...
-
Page 2: Contents Of The Box
Pro22218/43218 Installation Manual Contents of the Box B/G/A Rear ECU Front ECU Buzzer LCD Display Sensor Front On-Off Switch Quantity: 1pc Quantity: 1pc * Quantity: 1pc * Quantity: 1pc Quantity: 8pc Quantity: 1pc Rear Wire Harness Front Wire Harness Rear Power Cable Front Power Cable Silicon Ring Quantity: 4pc 4,5m... - Page 3 Pro22218/43218 Installation Manual Tools Drill Bit 10mm Electric Drill 17 wrench Solder Wire Soldering Tool Insulating Tape Drill Bit 4mm Marker Rasp and Cutter Cable Cutter Screwdriver Testmeter Tape Measure Heat Blower Alchol...
-
Page 4: Flush Mount
Pro22218/43218 Installation Manual Felt Prime Paint Warnish Outside Drill Flush Mount Angled Sleeves Silicon ring install after Silicon ring 3°/6°/12° Adhesive Tape paintwork! Silicon ring *Optional Sensor Sensor Drill Bit 20mm Drill Bit 16,4mm When mounted in the bumper, the adhesive holders can be mounted The sensors must never be directed downwards. - Page 5 Pro22218/43218 Installation Manual Outside Drill Type Flush Mount Type 90 ° 90 ° 3° 6° 12° =<12° 3° 6° 12°...
- Page 6 Pro22218/43218 Installation Manual...
- Page 7 Pro22218/43218 Installation Manual The sensors must not be mounted very tight, as this can lead to problems. Since the supplied drill bit has a very suitable diameter, the holes can easily be expanded as required. Max. +0,2mm Angled Angled Angled 3°...
- Page 8 Pro22218/43218 Installation Manual 10 mm inside 10 mm...
- Page 9 Pro22218/43218 Installation Manual <70°C CLEAN 16.4mm...
- Page 10 Pro22218/43218 Installation Manual Felt Prime Warnish Paint Outside Drill Flush Mount Angled Sleeves Silicon ring install after Silicon ring 3°/6°/12° Adhesive Tape paintwork! Silicon ring *Optional Sensor Sensor Drill Bit 20mm Drill Bit 16,4mm When mounted in the bumper, the adhesive holders can be mounted The sensors must never be directed downwards.
- Page 11 Pro22218/43218 Installation Manual Outside Drill Type Flush Mount Type 90 ° 90 ° 3° 6° 12° 3° 6° 12°...
- Page 12 Pro22218/43218 Installation Manual...
- Page 13 Pro22218/43218 Installation Manual L = 160~200 cm L = 160~200 cm A B C D A B C D 35/50/35 50/50/50 The sensors can be installed at 45~70 cm 45~70 cm different heights L = 160~200 cm L = 160~200 cm A B C D A B C D 20/80/20...
- Page 14 Pro22218/43218 Installation Manual The sensors must not be mounted very tight, as this can lead to problems. Since the supplied drill bit has a very suitable diameter, the holes can easily be expanded as required. Angled Angled Angled 3° 6° 12°...
- Page 15 Pro22218/43218 Installation Manual 10 mm Mark 10 mm inside...
- Page 16 Pro22218/43218 Installation Manual CLEAN 16.4mm...
- Page 17 Pro22218/43218 Installation Manual REAR Distance for Volume Wall High High High High Set the volume with the slide switch to a good audible level Last Zone Continuous tone For vehicles with a spare wheel mounted on the tailgate or with Fasten the control unit trailer coupling, the warning zone for the last zone (duration) can be extended from 30 to 50 cm.
- Page 18 Pro22218/43218 Installation Manual Option1 (FRONT) Option2 (FRONT) ACC 12V +RED BLACK (GND) YELLOW (Brake) GREY (Speed) 80 100 speed Fasten the control unit...
- Page 19 Pro22218/43218 Installation Manual B/G/A on-o switch Black (Ground) Solution 1 LCD DISPLAY GREY S02DSP00028 Orange Orange (+12V Reverse Lamp (+)) Solution 2 Test lamp and BLACK Orange Orange (+ACC) measuring equipment (+12V Reverse Lamp (+)) YELLOW Power BUZZER Power Connection: -Under normal circumstances, connect S12BZR00016 the orange wire to the reverse light...