Advertisement
Product Code: 6052
OWNER'S MANUAL
PRODUCT CODE: 6052
4 DRAWER
WORKSHOP TROLLEY
Dimensions
Warranty
Wheel Size
Load Capacity
Weight
850x445x972mm
1 Year
100mm
260kg
43.8kg
Drawer Capacities
Top Shelf
Top Drawer (2)
Middle Drawer
Bottom Drawer
Bottom Shelf
90kg
13kg ea.
22kg
32kg
90kg
Made in China to TQB Brands Pty Ltd specifications
Page 1
Visit us at www.tqbbrands.com.au
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TradeQuip 6052
Summary of Contents for TradeQuip 6052
- Page 1 Product Code: 6052 OWNER’S MANUAL PRODUCT CODE: 6052 4 DRAWER WORKSHOP TROLLEY Dimensions Warranty Wheel Size Load Capacity Weight 850x445x972mm 1 Year 100mm 260kg 43.8kg Drawer Capacities Top Shelf Top Drawer (2) Middle Drawer Bottom Drawer Bottom Shelf 90kg 13kg ea. 22kg 32kg 90kg Made in China to TQB Brands Pty Ltd specifications Page 1 Visit us at www.tqbbrands.com.au...
- Page 2 Product Code: 6052 WARNING IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE WARNING The instructions and warnings contained in this manual should be read and understood before using or operating this equipment. Do not allow anyone to use or operate this equipment until they have read this manual and have developed a thorough understanding of how this equipment works. Failure to observe any of the instructions contained in the manual could result in severe personal injury to the user or bystanders, or cause damage to the equipment and property. Keep this manual in a convenient and safe place for future reference. Whilst every effort has been made to ensure accuracy of information contained in this manual, the TQB Brands Pty Ltd policy of continuous improvement determines the right to make modifications without prior warning.
- Page 3 Always distribute objects evenly on the Workshop Trolley. Uneven weight distribution could cause tipping. Do not lean or climb onto the Workshop Trolley. Only use this device for the purpose for which it has been designed. Do not modify any component of this equipment. When servicing, use only Tradequip identical replacement parts. Use of any other parts will void the warranty. Only use on a flat surface capable of supporting the Workshop Trolley and its rated maximum capacity load. It is easy to lose control of the Workshop Trolley if attempting to pull a load on a sloping or uneven surface.
- Page 4 Product Code: 6052 Assemble the Cart: Assemble on a flat, level, hard and smooth surface capable of safely supporting a fully loaded Trolley. Attach two Swivel Castors (12) to one side of the Bottom Shelf (11), using eight sets of Hex Bolts (13), Spring Washers (3) and Nuts (4). (Figure A) Attach two Locking Swivel Castors (10) to the other side, using eight sets of Hex Bolts (13), Spring Washers (3) and Nuts (4). (Figure A) Attach a Cross Support (9) between two Right Posts (1), using one set of Bolts (2), Spring Washers (3) and Nuts (4). (Figure B) Repeat with remaining Cross Support and two Left Posts (6). (Figure B) Attach Posts with Cross Supports to the outside corners of the Bottom Shelf, using sixteen sets of Bolts (2), Spring Washers (3) and Nuts (4). (Figure C) Warning! The chest is heavy; do not attempt to lift and lower onto Cross Supports without assistance. With assistance, lift up the chest, then lower it carefully between the Posts until its bottom edges rest on the Cross Supports. (Figure D) Attach the Handle (7) to lower holes on same side as Locking Swivel Castors, using two Handle Bolts (8) and two Nuts (4). (Figure D) Secure Posts to chest with fourteen sets of Bolts (2), Spring Washers (3) and Nuts (4). 10. Tighten and secure all hardware nuts and bolts. Your Workshop Trolley is ready for use. Warning - Do not exceed the product's rated maximum load capacity. Made in China to TQB Brands Pty Ltd specifications Page 4 Visit us at www.tqbbrands.com.au...
- Page 5 Product Code: 6052 3. BEFORE USE Prior to each use conduct a visual inspection by checking for abnormal conditions, such as cracked joints and damaged, loose, or missing parts. 4. STORAGE This Workshop Trolley should always be stored in a dry location on a level surface. 5. MAINTENANCE Inspect the general condition of the Workshop Trolley checking: for loose hardware misalignment of binding or parts, cracked, bent, or broken parts, and any other condition that may affect the Workshop Trolleys safe operation. Clean the Workshop Trolley after each use. Ensure dirt, oil, grease and debris are not on the Workshop Trolley. 6. SERVICE & REPAIR Any 32 Bin Polyethylene Workshop Trolley found damaged in any way, or found to be worn or operates abnormally should be removed from service until repaired by an authorised service agent. Owners and / or operators should be aware that repair of this...
- Page 6 Product Code: 6052 PARTS LIST Part # Description QTY Part # Description QTY Right Post Handle Bolt (M8 x 16) Bolt (M8 x 12) Cross Support Spring Washer Locking Swivel Castor Nut Bottom Shelf Chest Castor Wheel Left Post Hex Bolt (M8 x 16) Handle Made in China to TQB Brands Pty Ltd specifications Page 6 Visit us at www.tqbbrands.com.au...
- Page 7 Product Code: 6052 WARRANTY Tradequip products have been carefully tested and inspected before shipment and are guaranteed to be free from defective materials and workmanship for a period of 12 months from the date of purchase except where tools are hired out when the guarantee period is ninety days from the date of purchase.
- Page 8 Product Code: 6052 TQB Brands Pty Ltd 1/40 Metrolink Circuit Campbellfield Victoria 3061 sales@tqbbrands.com.au Made in China to TQB Brands Pty Ltd specifications Page 8 Visit us at www.tqbbrands.com.au...
Need help?
Do you have a question about the 6052 and is the answer not in the manual?
Questions and answers