Subscribe to Our Youtube Channel
Summary of Contents for Manitou M48SF
- Page 1 M48SF Mulcher Operators Manual Phone: (866) 232-8224 E-mail: AttachmentInfo@Manitou-Group.com Website: Attachments.Manitou-Group.com Attachments.Manitou-Group.com...
- Page 2 Attachments.Manitou-Group.com...
-
Page 3: Table Of Contents
5.2 Attaching And Detaching ................12 5.3 Operation ......................12 5.3.1 Operational Information ..................12 5.3.2 Operation ........................13 6. Routine Maintenance ...............14 6.1 Inspections ......................14 6.2 Check Belt Tension ..................14 6.3 Replace Cutting Teeth .................14 6.4 Replace Coupler Spyder ................15 7. Troubleshooting ................16 Attachments.Manitou-Group.com... -
Page 4: Introduction And Warranty
1.2 Warranty Manitou Americas, Inc., warrants products purchased 1.1 Introduction from Manitou Americas to the Original Retail Purchaser to be free from defects in material and workmanship for Congratulations on your purchase of a Manitou Group a period of twelve (12) months from the warranty start Attachments Mulcher. -
Page 5: Component Identification
2. Component Identification 1 - Operators Manual Holding Tube 2 - Rotor 3 - Cutting Teeth 4 - Safety Push Bar 5 - Hydraulic Pressure Gauge 6 - Quick Attach Attachments.Manitou-Group.com... -
Page 6: Specifications
A6205 Motor: 12-20 gpm. 45-76 lpm. 1425 lb. A6210 Motor: 12-24 gpm. 45-91 lpm. 1 in. 48 in. 62 in. M48SF 646 kg. A6215 Motor: 16-25 gpm. 61-95 lpm. 25 mm. 1219 mm. 1575 mm A6220 Motor: 19-30 gpm. 72-114 lpm. -
Page 7: Safety
WARNING NOTICE Prevent serious injury or death. NOTICE - Indicates a situation that could result in damage to the equipment or other Verify mulcher is locked to quick attach property. hitch before operation or transport. Attachments.Manitou-Group.com... -
Page 8: Replace Safety Signs
• If you do not understand any part of this manual, Avoid sharp turns & sudden movement on slopes. • contact Manitou Group Attachments at 866-232-8224. Carry mulcher close to the ground. • Avoid holes, ditches and other obstructions which •... -
Page 9: Avoid Power Lines & Underground Utilities
Raised, unsupported mulcher can fall, understand this manual. If you do not understand any resulting in death or serious injury. part of the manual, contact Manitou Group Attachments at 866-232-8224. Never enter the area under a raised Always wear face and/or eye protection, safety shoes, mulcher. -
Page 10: Hazards From Modifying Equipment
To protect you and others against death or serious injury, all labels shown must be on mulcher and must be legible. Decal 1 If any of these labels are missing or cannot be read, contact your dealer for replacement labels. Attachments.Manitou-Group.com... - Page 11 Never allow riders; especially children on carrier or cutter. cutting Decal 4 Decal 2 Decal 5 (Behind Cover) unsafe Decal 3 Decal 6 Attachments.Manitou-Group.com...
-
Page 12: Operation
Verify that all hardware is tight. trees. Inspect hoses and fittings for wear, damage and leaks. Replace damaged or leaking hoses before use. Verify that local utilities have marked all underground wires, cables and pipelines. Refer to operating unit operator’s manual for prestarting instructions. Attachments.Manitou-Group.com... -
Page 13: Operation
Remove debris from rotor. The mulcher can mulch up to 1 in. (25 mm) below ground level. Excessive ground contact will result in rapid wear of the cutting teeth. Keep ground contact to a minimum. Attachments.Manitou-Group.com... -
Page 14: Routine Maintenance
Moving parts can crush and cut. Keep clear of moving components. Lockout operating unit before performing Inspect belt (2) for wear, damage and proper maintenance. tension. Inspect cutting teeth for damage. Replace individual Adjust idler (3) to set belt tension. teeth as needed. Attachments.Manitou-Group.com... -
Page 15: Replace Coupler Spyder
6.4 Replace Coupler Spyder Lower mulcher to ground. Stop skid steer engine and remove key. WARNING Moving parts can crush and cut. Keep clear of moving components. Lockout operating unit before performing maintenance. Remove inspection cover (1). Install hydraulic motor assembly. Attachments.Manitou-Group.com... -
Page 16: Troubleshooting
2,500 and 3,500 psi. Not enough oil flow. Check flow control on skid steer. See your dealer. Drive belt loose. Tighten drive belt. Excessive vibration. Cutting teeth worn or missing. Replace worn, broken or missing teeth. Debris lodged in rotor. Remove debris. Attachments.Manitou-Group.com... - Page 17 Attachments.Manitou-Group.com...
- Page 18 One Gehl Way P.O Box 179 West Bend, WI. 53095-0179 USA Phone: 866-232-8224 Attachments.Manitou-Group.com Revision June 2021 Attachments.Manitou-Group.com...
Need help?
Do you have a question about the M48SF and is the answer not in the manual?
Questions and answers