Subscribe to Our Youtube Channel
Related Manuals for Trango Systems STINGRAY VST2500
Summary of Contents for Trango Systems STINGRAY VST2500
- Page 1 STINGRAY 2.4 GHz Wireless Video/Audio/Alarm Transmission System Installation Operating Instructions...
- Page 2 • After the picture has been optimized tighten the bracket down using the knob on the side of the bracket as shown below. Copyright © 1999 Trango Systems, Inc. All rights reserved.
-
Page 3: Fcc Information
Save the packaging for further storage of the equipment. Service: If the unit ever needs repair service, contact your Trango Systems, Inc. distributor for return authorization and shipping instructions. FCC Information: Note: This equipme nt has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. -
Page 4: Installation Hints
3) If operating more than one system in an area, set the channels as far apart as possible on each system (i.e. system 1 use channel 1, system 2 use channel 4). Copyright © 1999 Trango Systems, Inc. All rights reserved. - Page 5 4. Left audio input – 1 Vpp 600 Ohm terminated RCA-F 5. Stereo/Alarm switch 6. Video input – 75 Ohm terminated RCA-F 7. Channel DIP switch 8. Status LED • FIGURE 2• Copyright © 1999 Trango Systems, Inc. All rights reserved.
- Page 6 The status LED will blink to indicate the channel number after the switch is changed. CAUTION CAUTION CAUTION CAUTION DO NOT APPLY EXTERNAL VOLTAGES TO THE ALARM INPUTS AS PERMANENT DAMAGE TO THE UNIT MAY RESULT. USE ONLY DRY CONTACTS WITH THESE INPUTS. Copyright © 1999 Trango Systems, Inc. All rights reserved.
- Page 7 3. Right audio output – 1.5 Vpp RCA-F 4. Left Audio output – 1.5 Vpp RCA-F 5. Stereo/Alarm switch 6. Video output-75 Ohm terminated RCA-F 7. Channel DIP switch 8. Status LED • FIGURE 4 • Copyright © 1999 Trango Systems, Inc. All rights reserved.
- Page 8 The status LED will blink to indicate the channel number after the switch is changed. CAUTION CAUTION CAUTION CAUTION DO NOT APPLY EXTERNAL VOLTAGES TO THE ALARM OUTPUTS. PERMANENT DAMAGE TO THE UNIT MAY RESULT. Copyright © 1999 Trango Systems, Inc. All rights reserved.
- Page 9 VTX2500 has a built-in 75 Ω termination. VIDEO TOO BRIGHT Make sure that the receiver video output line is terminated with 75 Ω . Check the Technical Support section of our website at http://www.trangosys.com/ additional assistance. Copyright © 1999 Trango Systems, Inc. All rights reserved.
- Page 10 Current Consumption: 145 mA typical 1 Vpp Max. Ripple Input: MECHANICAL: Cold Rolled Steel with ABS radome Material: Off-white powdercoat Finish: x” W x y”L x z”H without antenna Size: xxxx lb Weight: Copyright © 1999 Trango Systems, Inc. All rights reserved.
- Page 11 Reflects state of transmitter alarm inputs – updated twice per Output Level: second POWER SECTION: 7 Vdc nominal, 6-12 Vdc Input Voltage Range: 1 Vpp Max. Ripple Input: Current Consumption: 400 mA nominal Copyright © 1999 Trango Systems, Inc. All rights reserved.
- Page 12 Material: Off-white powdercoat Finish: x” W x y”L x z”H without antenna Size: xxx lb Weight: ENVIRONMENTAL: 0 to 50 ºC Operating Temp.: -40 to 85 ºC Storage: 95% non-condensing Humidity: Copyright © 1999 Trango Systems, Inc. All rights reserved.
Need help?
Do you have a question about the STINGRAY VST2500 and is the answer not in the manual?
Questions and answers