Advertisement
Installation
Before Installation
Cerio Force Power Multi Gigabit Edge PoE Adapters are
able to extend PoE to the Edge PoE equipment (Such as small
PoE Switch) to delivery power and data to PD device through
the 4Pair UTP Ethernet cable connecting the Unit-1 and Unit-2.
Cables Installation
Cerio Force Power Multi Gigabit Edge PoE Adapters can
provide both data and power for distances of up to 100 meters
from the power source (90Watt) and without cable-loss when
using CAT 6 or up cabling.
The setup of the Edge PoE Adapters can be performed using the
following steps:
Unit-1 ( PSE for Uplink Source and POE Downlink connection ):
Connect the included 90Watt power supply DC power Cable to
the "DC Jack Port" of Unit1
Connect your Ethernet cable (Cat6 or up cable) from your data
source to the "Data In port" of the Unit-1
Connect an Ethernet cable (Cat6 or uplink cable) from the "PWR
+ Data Output Port" of "Unit-1" to your "Unit-2" with an
extended distance (Max.100 meters) for Get power extension to
end device enable devices.
Unit-2 ( PD for POE receive and DC / DATA splitter connection ):
Connect "Power+Data" port on "Unit-2" and "PWR+ Data Out"
port form "Unit-1" with Ethernet cable, make sure "Power" LED
of "Unit-2" is on.
Connect "Power OUT" cable on "Unit-2" to power DC Jack of the
network end device and connect "Data OUT" cable on "Unit-2" to
RJ45 port of network end device. (Ex. Edge. POE Switch for end
POE Device such as POE IPCAM or POE WIFI AP )
Check whether the network device is LED on. If not, please make sure that
power is on for Unit-1 and Unit-2, and all cables are connected correctly.
Units Combination
This device can be locked on the wall, (Does not have screw
attachment, you must prepare it yourself) or it can be
combined with multiple units for easy to bundles organize the
Ethernet cables
Product Application
Notice: Cable and Power Loss
@ 100Meter : Keep power source ability (60Watt) with Cat.6 or up Cable
@ 100Meter : " 14Watt " with Cat.5e Cable
Product Specifications
Standards & Hardware Specifications
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
Standard
IEEE 802.3ab 1000BASE-T
IEEE 802.3bz 2.5G/5GBASE-T
10BASE –T: UTP Cat. 3 or up
Network Media
100BASE-TX: UTP Cat.5 or up
1G/2.5G/5GBASE-T : UTP Cat.5e or up
10M/100M/1G/2.5G/5G (Half-duplex),
Data Transfer Rate
20M/200M/2G/5G/10G (Full-duplex)
PoE Type
Passive POE
Data PIN
PIN 1/2, 3/6 & 4/5, 7/8
End-span (Type-A): PIN 1/2,3/6
Power PIN
Mid-span (Type-B): PIN 4/5,7/8
RJ-45 x1 for Power + Data
Ethernet Connector
RJ-45 x1 for Data
Power Connector
DC Jack
Supports ESD (Electro Static Discharge)
ESD Protection
Over Voltage protection and Short Circuit
Protection
Environmental & Mechanical Characteristics
Max Power
90Watt
Output
Power Requirement
56V 90Watt External Power Supply
PoE Input Voltage
50V~57V
@ 100Meter : Keep power source ability
Cable and Power
(90Watt) with Cat.6 or up Cable
Loss
@ 100Meter : " 14Watt " with Cat.5e Cable
LED Indicators
System LED: Power (Green) x1
Operating
0° to 55° C
Temperature
Storage Temperature
-40° to 70° C
Operating Humidity
5% to 90% non-condensing
Storage Humidity
5% to 90% non-condensing
Dimension
64.8 x 51.7 x 24mm ( W x D x H )
Unit Weight
PSE Unit : 38g , PD Unit :38g
Case of Materials
ABS
Production Location
TW
Certification
FCC, CE, RoHS-compliant
v1.5
Advertisement
