Advertisement
3.
INTRODUCTION
Kit features snap together pipe work for speed and threaded attachments for strength. Connecting parts are zinc or cadmium plated for long,
rust-free life. Components are manufactured from high quality steel and finished with red supergloss paint.
IMPORTANT:
Only fully trained and qualified persons should use this equipment. It is very important that the user understands the applications, limitations and
potential hazards of the product.
VEHICLE DAMAGE INTRODUCTION
Before using the repair kit, you must determine the extent of vehicle damage. The technician will check all parts and determine if there is any
broken, torn, crumpled, wrinkled, crushed, twisted or bent metallic parts. Measurements should be taken to see how far out of alignment the
vehicle may be. It is important to determine correct dimensions by referring to the manufacturer’s frame dimension charts and specifications.
Remember, do not commence pushing until you are sure when to stop. Take time to examine and determine damage correctly. Comprehensive
planning will save you time when you are actually using this equipment.
4.
INSTRUCTIONS FOR USE
To provide maximum versatility a combination of pump accessories may be used.
Illustrated below are the main attachment variations
Ensure the task you are undertaking falls within the capacity of the pump and accessories you are using.
WARNING! Ensure you have read and understood section 1 safety instructions.
p
p
4.1.
The pump may be use in any position from horizontal to vertical. When not horizontal ensure the hose
end of the pump is down.
4.2.
To use the pump, close valve (fig 1.A) by turning the knob clockwise and pump the the handle up and
down to apply the load.
4.3.
To release pump pressure, turn knob anti-clockwise (B).
5.
MAINTENANCE
IMPORTANT: Only fully qualified personnel should attempt maintenance or repair to the hydraulic system.
5.1.
Pump oil level
Release pressure and disconnect the ram from the pump.
Hold pump in an upright position.
Remove filler plug and add hydraulic oil until it is level with the full mark (fig 2).
WARNING: DO NOT use brake fluid, or any fluid other than hydraulic jack fluid, as this may cause serious damage to the pump/ram
p
p
and will invalidate the warranty! Use only Sealey hydraulic oil.
5.2.
General
Before each use check for broken, cracked, bent, or loose parts, or any visible damage to welds, ram, pump, hose and accessories.
If any suspect item is found remove from service and take necessary action to remedy the problem.
Replace/repair with genuine parts only. Unapproved parts may be dangerous and will invalidate the warranty.
Keep all parts of the kit clean.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE PUMP AND/OR RAM.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PUMP OR RAM TO US. Please telephone us on 01284 757500 to obtain the address and ‘phone number of your local agent.
If product is under guarantee please contact your dealer.
De-commissioning Hydraulic Pump/Ram
Should the pump or ram become completely unserviceable draw off the oil into an approved container and dispose of the product and the oil
according to local regulations.
Declaration of Conformity
10 TON SUPERSNAP
BODY REPAIR KIT
®
Models: RE83/10/SK
98/37/EC Machinery Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
We, the sole importer into the UK, declare that the product listed below is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national
authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
Sole UK Distributor,
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 757500
01284 703534
fig 1
A
B
fig 2
For Jack Sealey Ltd.
Sole importer into the UK
29th March 2001
of Sealey Power Products.
E-mail: sales@sealey.co.uk
RE83/10/SK - 2 - 180105
Advertisement
