Advertisement
Quick Links
Marshall Electronics
B r o a d c a s t A / V D i v i s i o n
VS-PTC-50
Camera PTZ/On-Screen Display Menu
Mini Joystick Controller
User Manual
Thank you for purchasing this Marshall Electronic's product.
Please read the User Manual thoroughly before attempting to setup & use.
If you have any problems with this product please contact Marshall Electronics.
Tel: (800) 800-6608 / (310) 333-0606
www.LCDracks.com
Advertisement
Related Manuals for Marshall Electronics VS-PTC-50
Summary of Contents for Marshall Electronics VS-PTC-50
- Page 1 User Manual Thank you for purchasing this Marshall Electronic’s product. Please read the User Manual thoroughly before attempting to setup & use. If you have any problems with this product please contact Marshall Electronics. Tel: (800) 800-6608 / (310) 333-0606 www.LCDracks.com...
-
Page 2: List Of Items
1. Joystick 2. LCD screen Prese t Tele Wide 3. Function keys 4. Speed dome Setup and recall keys Shot Nea r Ope n Patter n Clos e Ru nA ut o Ca m Aux on Aux off ④ VS-PTC-50 Manual... - Page 3 (Esc) Exit key: exit and back to previous menu; (Setup) Setup key: press and hold for 3s to setup keyboard’s parameter. (F1) Adjust the control speed, it has 4 level: 1, 2, 3, 4 (Preset) Preset special status of ptz (including direction and zoom times). This key should be used together with number key;...
-
Page 4: Lcd Screen
2.1.2 Combined key operations mean 2 or more keys, or key and joystick are pressed, the corresponding PTZ will respond. — — Single-press keys include: Near, Far, Tele, Wide, Open, Close, Auto, F1, Run, Esc, joystick. The operations include: Preset, Pattern, Shot, Cam, Setup. VS-PTC-50 Manual... - Page 5 2.2 Detailed introduction to com 2.2 Detailed introduction to com 2.2 Detailed introduction to com 2.2 Detailed introduction to combined keys 2.2.1 Select PTZ ID: 2.2.1 Select PTZ ID: 2.2.1 Select PTZ ID: select speed dome or decoder whose ID is 28: pres 2.2.1 Select PTZ ID: select speed dome or decoder whose ID is 28: pres select speed dome or decoder whose ID is 28: pres...
- Page 6 PTZ parameter. you can set other PTZ parameter. you can set other PTZ parameter. — — you can set other PTZ parameter. — — — — — — — — — — VS-PTC-50 Manual — — — —...
-
Page 7: System Parameter Setup
PTZ addr： P:PELCOD 0-255 after finishing all setup, press【ESC】key to quit setup. P:PELCOD PTZ addr： 0-255 P:PELCOD P:PELCOD Follow above steps, all PTZ’s protocol and baud rate will be se Note: Follow above steps, all PTZ’s protocol and baud rate will be se Follow above steps, all PTZ’s protocol and baud rate will be se Follow above steps, all PTZ’s protocol and baud rate will be se Note:... - Page 8 Enter again： 4 digit number *system setup close、low Key-press 、 Move joystick to select mid、high sound volumn Key backlight close、30S、60S、 Move joystick to select (optional) 120S、open Move and press Default factory setup joystick to select — 09 — VS-PTC-50 Manual...
- Page 9 T Y P IC A L C O N N E C T IN G D IA G R A M 4. Typical Connecting Diagram 4. Typical connecting diagram DC connector RS485 cable Power supply cable (DC 12V) VS-PTC-50 Camera OSD Controller (+) Twisted Pair (-) Twisted Pair Can connect max. 255 cameras — — www.LCDracks.com...
- Page 10 Check the ID simultaneously have the same when operate of speed domes address code or not. the keyboard Set different address. controller No key tone Turn on key tone in system settings VS-PTC-50 Manual...
- Page 11 Marshall Electronics, Inc. 1910 East Maple Ave. El Segundo, CA 90245 Tel: (800) 800-6608 • (310) 333-0606 Fax: 310-333-0688 www.LCDracks.com support@marshall-usa.com...
Need help?
Do you have a question about the VS-PTC-50 and is the answer not in the manual?
Questions and answers