Advertisement
Installation
Before Installation
If the device is generally DC-receiving and does not support the POE
function, the FPOE-PD80 can easily be used to accept POE source
power and apply it separately from DC output power.
The FPOE-PD80 separates the power out and provides three kinds of
DC power output through its DIP switch and its voltage and current
shown as below:
DIP Switch :
• 12 VDC / 4.17A (Max)
• 19 VDC / 3.94A (Max)
• 24 VDC / 3.33A (Max)
Caution: Please ensure the output voltage is correct for remote
device. Otherwise it will damage your remote device.
Cables Installation
FPOE-PD80 provides a POE-powered solution for non-PoE devices.
The setup of the splitter can be performed using the following steps:
Connect from "DATA OUT" of FPOE-PD80 to the RJ-45 port of the
remote device.
Make sure first power source that the POWER+DATA in Port of
the splitter is fully connected to the PoE source-powered PoE
Injector or PoE Switch.
Connect the correct DC plug from "DC OUT" of FPOE-PD80 to
the DC port of remote device. (Use a DC cable to connect
devices that are to be powered by DC)
Power on the remote device and the LED for voltage status
indicator on FPOE-PD80 will remains on.
Units Combination
This device can be locked on the wall, (Does not have screw
attachment , you must prepare it yourself) or it can be
combined with multiple units for easy to bundles organize the
Ethernet cables.
LED Indicator :
Output power switching (12VDC / 19VDC / 24VDC)
LED indicators for Power function enable
DC 12V output: 12V Light on
LED Definition
DC 19V output: 19V Light on
DC 24V output: 24V Light on
Notice: Cable and Current-Resistance Loss
DC 24V @ 100Meter : 12.50% with Cat.6 Cable
DC 19V @ 100Meter : 13.33% with Cat.6 Cable
DC 12V @ 100Meter : 14.00% with Cat.6 Cable
Product Specifications
Standards & Hardware Specifications
IEEE802.3/3u 10BASE-T/100BASE-TX
IEEE 802.3ab 1000BASE-T
Standard
IEEE802.3af Power over Ethernet (PoE)
IEEE802.3at Power over Ethernet (PoE+)
Compatible to IEEE 802.3bt Power Level (PoE++)
10/100BASE-T/TX : UTP Cat. 5 or up
Network Media
1000BASE-T: UTP Cat. 5 or up
10/100/1000Mbps (Half-duplex),
Data Transfer Rate
20/200/2000Mbps (Full-duplex)
Data PIN
PIN 1/2, 3/6 & 4/5, 7/8
End-span (Type-A): PIN 1/2,3/6 ;
Power PIN
Mid-span (Type-B): PIN 4/5,7/8
RJ-45 x1 for Power + Data input
Ethernet Connector
RJ-45 x1 for Data output
ESD Protection
Over Voltage protection &Short Circuit Protection
Environmental & Mechanical Characteristics
Max Power
80Watt(DC 24V Output),75Watt(DC 19V Output)
Output
50Watt(DC 12V Output)
Power Interface
DC-Jack
Power Requirement
50~57V PoE Power Source
PoE Input Voltage
50V~57V
DC Output
12V/19V/24V three range adjustable by DIP
Control Range
switch
DC Output Current
24V/3.33A , 19V/3.94A, 12V/4.17A
LED Indicators
DC Output LED x3 : 12V or 19V or 24V
Operating
0° to 55° C
Temperature
Storage Temperature -40° to 70° C
Operating Humidity
10% to 90% non-condensing
Storage Humidity
5% to 90% non-condensing
Dimension
84.5 x 80 x 39.5mm ( W x D x H )
Unit Weight
99.8g
Case of Materials
ABS
Production Location
TW Only
Certification
FCC, CE, RoHS-compliant
v1.5
Advertisement
