Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Mako StyliCleaner
- Page 1 Getting started: Getting Started StyliCleaner LK v2022-04...
- Page 2 Introduction This presentation describes how a StyliCleaner should be put into use. Follow all future instructions. All these instructions are also described in the manuals supplied. Getting Started StyliCleaner LK v2022-04...
-
Page 3: Contents Of The Packaging
Contents of the packaging The following parts are included in the plastic box of the StyliCleaner: 1) Control unit 2) Cleaning unit 3) Manuals 4) CE-Declaration 5) Power supply 6) T-piece for compressed air supply 7) Spare O-rings 8) Socket screw... -
Page 4: Control Unit
Make sure that the compressed air hose between the control unit and the cleaning unit is as short as possible. As a result, there is a little chance that there is still cleaning liquid in the hose after performing a cleaning. Getting Started StyliCleaner LK v2022-04... - Page 5 Installation control unit using "plateholder" A special "plateholder" is also available to hold the Control Unit to the side of a CMM. We include a set of adhesive pads or ‘Velcro coins’ for the back of the plateholder. Getting Started StyliCleaner LK v2022-04...
- Page 6 Place the control unit on the back of the measuring machine. This is "usually" placed under the parking position of the measuring machine. This allows the compressed air hose Ø4mm between control unit and cleaning unit to be as short as possible. Getting Started StyliCleaner LK v2022-04...
- Page 7 Connection cleaning unit Connect the cleaning unit to the control unit. 1) Connect the black cable to the cleaning unit 2) Compressed air hose Ø4mm cleaning unit 3) Compressed air hose Ø4mm control unit Getting Started StyliCleaner LK v2022-04...
-
Page 8: Connection Power Supply
Do not plug the power supply into an outlet. We will only do this when the entire StyliCleaner is connected. There are also 2 additional connection adapters for the power supply. Use this if necessary. Getting Started StyliCleaner LK v2022-04... -
Page 9: Cleaning Liquid
Never use heptane for this (this will eventually damage various parts). Use (if possible) refill bottles with pipette (if possible). Unscrew the gray screw and fill the liquid through the opening. Fill the tank maximum by 75% and screw the gray screw back on. Getting Started StyliCleaner LK v2022-04... - Page 10 Spare parts O-rings 2 spare O-rings are supplied with the StyliCleaner. You can use these O-rings if the O-ring breaks when the cleaning liquid is being refilled. Getting Started StyliCleaner LK v2022-04...
-
Page 11: Connecting Compressed Air
2) Place the T-piece behind the air filters 3) Place the compressed air hose Ø6mm on the T-piece 4) Place the compressed air hose Ø6mm on the control unit 5) Put compressed air on the system Getting Started StyliCleaner LK v2022-04... - Page 12 The cleaning unit is placed on the CMM and connected c) Reservoir filled with the cleaning fluid d) Compressed air on the system The last thing to do now is to install the programs to use the StyliCleaner in practice. Getting Started StyliCleaner LK v2022-04...
- Page 13 Installation for LK CAMIO Users The proximity sensor controls the StyliCleaner. It has no direct link to the software (CAMIO). This means it works with any version of CAMIO, but older versions may need customized routines, not included as standard.
- Page 14 Installation for LK CAMIO Users To use the StyliCleaner with CAMIO, you must first fit it to the CMM table, set it square to an axis, then run the alignment routine. The alignment routine is one of four programs included in the LK CAMIO StyliCleaner folder: •...
- Page 15 3. Open and run the program ‘AlignSet.dmi’ which should now show a window as in next figure. 4. Leave the sections ‘1’ and ‘2’ as default. The program will update them. 5. Update Section ‘3’ to the current Cleaning Unit orientation. Getting Started StyliCleaner LK v2022-04...
- Page 16 8. With the probe commands altered, continue running the rest of the program. Make sure you keep the speed slow on your first run of this routine. 9. If the program completes successfully, you are now ready to use the StyliCleaner. Getting Started StyliCleaner LK v2022-04...
- Page 17 IMPORTANT NOTE: The ‘CleaningRoutine.dmi’ program runs commands without calling a specific probe. This means it will crash without having a probe specified. DO NOT RUN THIS PROGRAM AS A STANDALONE PROGRAM. Getting Started StyliCleaner LK v2022-04...
- Page 18 Using the StyliCleaner Routine inside your program To use the StyliCleaner routine inside your program, execute the following command: CALL/EXTERN,DMIS,'C:\LK\Appdata\StyliCleaner\CleanRoutine\CleanRoutine.DMI' You can either copy this directly from this document or execute it from the tabs inside CAMIO. To run/create this command in CAMIO, follow these steps: 1.
- Page 19 Using the StyliCleaner Routine inside your program 4. Use the ellipsis button to the right of the ‘Routine’ textbox to browse to this location: ‘C:\LK\Appdata\StyliCleaner\CleanRoutine\’ then select the ‘CleanRoutine.dmi’ program. 5. Click ‘OK’. CAMIO will enter the routine, and the program will open.
- Page 20 Finally By using the StyliCleaner we can fully automatically remove "light pollution" from the probe. Stubborn dirt is not removed. We therefore always have to carry out the removal of stubborn dirt manually. Never use heptane as a cleaning liquid.
Need help?
Do you have a question about the StyliCleaner and is the answer not in the manual?
Questions and answers