Advertisement
Quick Links
Step 1:
Start with the OMNI DRIVE™ Engine in the closed position (shown). Place
the OMNI DRIVE™ Engine on sill surface ensuring it is sitting flat. Align
engine holes with prefabricated holes closet to the center of the sill. Insert
the #10 x ½" undercut mounting screw(s). Using a Phillips head screwdriver
fasten the Engine to the frame.
Caldwell Manufacturing Company North America, LLC
Phone: (888) 347-7771
Fax: (585) 352-3729
OMNI DRIVE™
(Surface Mount)
Step 2:
Cover Engine holes with the two caps
provided.
Installation Instructions
Web: www.caldwellmfgco.com
Email: CService@caldwellmfgco.com
Advertisement
Related Manuals for Caldwell OMNI DRIVE
Summary of Contents for Caldwell OMNI DRIVE
- Page 1 Step 1: Start with the OMNI DRIVE™ Engine in the closed position (shown). Place the OMNI DRIVE™ Engine on sill surface ensuring it is sitting flat. Align engine holes with prefabricated holes closet to the center of the sill. Insert the #10 x ½”...
- Page 2 Align the prefabricated hole with the hole in Slide the right lock bar to the left (opening track. Insert the #10 x ½” undercut the OMNI DRIVE™). Slide the left lock bar mounting screw(s). Using a Phillips head through the left track. Drop over the pin screwdriver fasten the track to the frame.
- Page 3 Step 9: Slide the left lock bar to the right (closing the OMNI DRIVE™). Align the prefabricated hole with the hole in left track. Insert the #10 x ½” undercut mounting screw(s). Using a Phillips head screwdriver fasten the track to the frame.
- Page 4 Installation Instructions (Surface Mount) Step 10: Slide lock bars left and right to ensure the OMNI DRIVE™ operates smoothly free of and obstruction. Typically wrong screws used or proud screw heads cause drag. Step 11: Apply gasket on the Handle Housing, by exposing the adhesive strip and aligning the holes.
- Page 5 Step 13: Rotate handle 180 degrees to the open position so the Engine Arm Receiver is angle outward. Caldwell Manufacturing Company North America, LLC Phone: (888) 347-7771 Web: www.caldwellmfgco.com Fax: (585) 352-3729 Email: CService@caldwellmfgco.com...
- Page 6 Insert vent arm into the vent track. Step 16: Slide vent arm until the arm is in position resting on the OMNI DRIVE™ engine arm receiver as shown. Fasten the track using the remaining hole. Caldwell Manufacturing Company North America, LLC Phone: (888) 347-7771 Web: www.caldwellmfgco.com...
-
Page 7: Installation Completed
422) insert the two 10-32 x ¼” security button head cap screws as shown & tighten to a snug torque Step 19: INSTALLATION COMPLETED Caldwell Manufacturing Company North America, LLC Phone: (888) 347-7771 Web: www.caldwellmfgco.com Fax: (585) 352-3729 Email: CService@caldwellmfgco.com... - Page 8 NEED TO INCREASE CLOSURE (Pull Vent In) Vent will close & handle does not return to zero. NEED TO DECREASE CLOSURE (Push Vent Out) Caldwell Manufacturing Company North America, LLC Phone: (888) 347-7771 Web: www.caldwellmfgco.com Fax: (585) 352-3729 Email: CService@caldwellmfgco.com...
- Page 9 Tighten the two 10-32 x ¼” security head cap the two 10-32 x ¼” security head cap screws screws using a 5/32” security hex driver. using a 5/32” security hex driver. Caldwell Manufacturing Company North America, LLC Phone: (888) 347-7771 Web: www.caldwellmfgco.com Fax: (585) 352-3729...