Table of Contents
Advertisement
Quick Links
DESCRIPTION
Structure in aluminium
Powder coated
3.66 x 2.14 m
CONFORM
European standard
NF EN 750
The time to make the assembly of this goal is estimated, for 2 people, at 45 minutes. (without sealing).
According to the decree above, for the first installation the goal must be tested like below :
-Put a vertical and static charge of 180 kg, on the middle of the crossbar,
- Put an horizontal charge of 110kg at the same point
After testing, the equipment and the fixation system or counterweight should not fail, displace or deform.
When the goal is not used it must be sealed or be stocked somewhere that people can't used it.
During the first installation, this stability and solidity test is compulsory.
Every time that the equipment
The owner must regularly check the condition of the product, and be sure that it meets the current safety standards.
In order to use our products at there best, it is recommended to follow carefully the notice of instruction, where you
can find the conditions of assembly ; installation ; maintenance ; storing.
The equipement has to be regularly maintained by the owner. It is adviced to:
- Check every week that all the screws are correctly tightened
- Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufactu-
rer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Clean the product by using dishwasher soap, clean water, and soft cloth.
One full year parts and labor guarantee. Every claim regarding condition of the delivered equipment has to
be done within the legal period of the reception of the material. The warranty will not apply to:
-
all degradation during the transport.
-
all degradation due to use differing from which was intended.
-
all degradation due to poor maintenance.
-
any defect claimed after the end of the legal period.
-
any damaged due to a faulty installation and assembly of the module
PRODUCT REF
Assembly TIME
TEST AFTER INSTALLATION
is
assembled, a visual check of the stability and solidity must be realized.
MAINTENANCE
WARRANTY
PRODUCT SHEET
ALUMINIUM HOCKEY GOAL
S22258
:
PAIR
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HotShot S22258
Summary of Contents for HotShot S22258
- Page 1 PRODUCT SHEET ALUMINIUM HOCKEY GOAL S22258 PAIR PRODUCT REF DESCRIPTION Structure in aluminium Powder coated 3.66 x 2.14 m CONFORM European standard NF EN 750 ASSEMBLY TIME The time to make the assembly of this goal is estimated, for 2 people, at 45 minutes. (without sealing).
- Page 2 IMPLANTATION & SEALING 1000±10mm Field limit 1250±10mm 2000±10mm 2500±10mm Concrete bloc Concrete bloc 500x500x500mm 500x500x500mm Important : The distance A has to be determined by the installer. When the goal is not used, the top of the cap must be at the same level than the ground.
- Page 3 ASSEMBLY NECESSARY TOOLS (NOT INCLUDED) Wrench 17mm Allen wrench 6mm Allen wrench 5mm INCLUDED ITEMS 1– ASSEMBLY OF CROSS-BAR TO THE 2 SIDE FRAMES (x4) Countersunk screws M10x30 Cross bar Left side frame NECESSARY ITEMS...
- Page 4 ASSEMBLY 2– ASSEMBLY OF REAR FRAME TO THE SIDE FRAMES (x4) Screws M10x70 + spring washer 10 NECESSARY ITEMS 3– ASSEMBLY OF NET (x2) Countersunk screws M8x30 Remove the rods, put the net in position and fix the rods again NECESSARY ITEMS...
- Page 5 ASSEMBLY 4– FIXATION OF THE PRODUCT TO THE GROUND (x4) SS eyebolt + SS washer 12 Hook NECESSARY ITEMS...
- Page 6 PACKING LIST HOCKEY GOAL ALUMINIUM PRODUCT REF S22258 Index G PAIR NOMENCLATURE Package Weight Dim. Index Designation Description Quantity Packing Method N° (kg) (mm) Plastic bubble + S22258-01 Cross-bar 3750x120x100 carton 2 layers 1 + 1 2300x1520x100 Side right frame +...
Need help?
Do you have a question about the S22258 and is the answer not in the manual?
Questions and answers