Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Advertisement
Table of Contents
Summary of Contents for ALZRC Mr.Q-190
- Page 1 组装手册 INSTRUCTION MANUAL...
-
Page 2: Table Of Contents
操作之前，请务必详阅本说明书，相信一定能够给您带来相当大的帮助，也请您妥善保管这本说明书，以作为日后参考。 Thanks for choosing ALZRC, there’s some matters need attention and knowledge you need to know， then just enjoy flying with remote control helicopter. Before you begin, please read this manual very carefully for your safety and also keep this manual properly for reference. - Page 3 规格说明 SPECIFICATION INSTRUCTION 规格说明 SPECIFICATION INSTRUCTION 使⽤4⼨螺旋桨 Apply 4 inch Propeller 166mm 138mm 138mm 166mm 轴距 190mm Wheelbase Distance 190mm 150mm 55mm 脚架高度 10mm Hight of foot 10mm 使用 1806 - 2400KV 无刷马达 Apply 1806 -2400KV Brushless Motor 机身(长x宽x高)：166 x 166 x 55mm Fuselage(LxWxH) : 166x166x55mm 重量：空机...
- Page 4 自备设备 EQUIPMENT REQUIRED FOR ASSEMBLY 自备遥控及电子设备 RADIO TRANSMITTER AND ELECTRONIC EQUIPMENT REQUIRED FOR ASSEMBLY 空机版自备遥控及电子设备 (Need prepare following equipments by yourself) 1、1806 - 2400KV 无刷电机 x 4 1、1806 - 2400KV Brushless Motor x 4 2、16A 无刷电调 x 4 2、16A Brushless ESC x 4 3、BEC分电板...
-
Page 5: 碳纤机身侧板-右 Chapter
组装说明 ASSEMBLY SECTION 碳纤机身侧板-右 出厂零件包装如果是已组装品，请务必确认各部件是否 Carbon Fiber Main Frame-R 锁紧上胶。 Chapter 1 For original manufactory package, If the product is already assembled by factory, please check again if parts are firmly secured and applied with some glue. 螺纹 Thread 碳纤机身侧板 M2.0 Carbon Fiber Main Frame 机身方形铝柱... -
Page 6: 碳纤机臂/底板 Chapter
组装说明 ASSEMBLY SECTION 碳纤机臂/底板 Carbon Fiber Motor Arm/Base Plate Chapter 3 第1步组装完成 Assembled in Chapter 1 第2步组装完成 Assembled in Chapter 2 碳纤底板 Carbon Fiber Base Plate 1.2mm 注意：螺丝平头面为底面。 碳纤机臂 Note: Flat side of the screw is the bottom side. Carbon Fiber Motor Arm 2.5mm 碳纤机臂... - Page 7 组装说明 ASSEMBLY SECTION 飞控板/电调板 Autopilot Plate/ESC Plate 16A无刷电调(三) 16A Brushless ESC (III) 将电调插头拉伸到机臂的各个方向。 Dispatch ESC Plug to all directions of the arm. 16A无刷电调(二) 16A Brushless ESC (II) 16A无刷电调(四) 16A Brushless ESC (VI) 16A无刷电调(一) 16A Brushless ESC (I) 第4步组装完成 Assembled in Chapter 4 出厂零件包装如果是已组装品，请务必确认各部件是否...
-
Page 8: 图传发射 Chapter
组装说明 ASSEMBLY SECTION 图传发射 Video Transmitter Chapter 5 图传发射 Video Transmitter 机身六角铝柱 第4步组装完成 Fuselage Hex Assembled in Chapter 4 Aluminum Post 4x25mm 图传发射安装后用扎带固定 Fix the Video Transmitter by zip tie after finish install it 平头内六角螺丝 Flat Head Hex Socket Screw M2x5mm 将图传发射连接到飞控板... -
Page 9: 电池板安装 Chapter
组装说明 ASSEMBLY SECTION 电池板安装 Installation of Battery Mount Chapter 7 平头内六角螺丝 Flat Head Hex Socket Screw M2x5mm 第6步组装完成 Assembled in Chapter 6 电调板电源输入 JST 固定示意图 Fixed Sketch for ESC Plate Power Input JST 第5步组装完成 Assembled in Chapter 5 摄像头 Camera 摄像头... -
Page 10: 接收器固定板 Chapter
组装说明 ASSEMBLY SECTION 接收器固定板 平头内六角螺丝 Receiver Tray Support Flat Head Hex Socket Screw Chapter 9 M2x5mm 接收器护板 - 右 Receiver Backplate - R 碳纤接收器固定板 接收器护板 - 左 接收器固定板安装示意图 Receiver Tray Support Receiver Backplate - L Assembly Sketch for 1.2mm Receiver Tray Support 摄像头链接到飞控板时，请根据摄像头的支持电压... -
Page 11: 1806 Brushless Motor
组装说明 ASSEMBLY SECTION 1806 无刷马达 无刷马达 - 正转 1806 Brushless Motor Brushless Motor - CW Chapter 11 1806 - 2400Kv Mr-1806 Mr-1806 2400KV-CW 2400KV-CCW 马达保护座 无刷马达 - 反转 Motor Protection Brushless Motor - CCW Support 1806 - 2400Kv 将马达插头相对应插入电调插头 通电后，如马达反转，拔出反转 插头再插即可。... -
Page 12: 电池/图传发射天线 Chapter
组装说明 ASSEMBLY SECTION 电池/图传发射天线 Battery/AV Transmitter Antenna Chapter 13 聚合物锂电池 Li-Po Battery 850mAh ~ 1000mAh 长宽高不能超过 75mm x 35mm x 22mm Maximum Size 75mm x 35mm x 22mm 电池魔术贴 - 母贴 Velcro of Battery - Loop 电池魔术贴 - 公贴 Velcro of Battery - Hook 侧面图...
Need help?
Do you have a question about the Mr.Q-190 and is the answer not in the manual?
Questions and answers