Ice machine operation............Using your freezer ..............CAUTION- Hazards or unsafe practices which could result in Dimensions For 15CM Solid Door........... personal injury or property or product damage. Recommended Rough in Opening Dimensions For 15CM Solid Door............Dimensions For 25CM Solid Door........
UNPACKING YOUR ICE MACHINE OR FREEZER Warranty Registration Remove Packaging Your ice machine has been packed for shipment with all parts It is important you send in your warranty registration card im- that could be damaged by movement securely fastened. Cut mediately after taking delivery of your ice machine or you can the banding material at the bottom of the carton, unfold the register online at www.marvelscientific.com.
INSTALLING YOUR ICE MACHINE OR FREEZER Select Location Leveling Legs The proper location will ensure peak performance of your ap- Adjustable legs at the front and rear corners of the unit should pliance. We recommend a location where the unit will be out be set so the unit is firmly positioned on the floor and level from of direct sunlight and away from heat sources.
HANDLE INSTALLATION Handle Installation (Solid Door Models) Remove the handle, (2) screws, and 5/32” allen wrench from the bag shipped inside the cabinet. Locate handle opposite the hinges and secure in place using the (2) screws and the allen wrench. (See Figure 3).
DOOR ALIGNMENT Door Alignment Procedure The door should be parallel to the sides and top of the refrig- erator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side. Use a 5/32” allen wrench for this procedure.
INSTALLING THE ICE MACHINE WATER SUPPLY Water Supply NOTE Observe and follow all local building codes when installing this appliance. Attach the supplied water line adapter (Figure 6) to the water valve inlet on the back of the ice machine (See Figure 5). Be sure the rubber washer is in place in the inlet valve nut.
USING YOUR ICE MACHINE Turning on the ice machine Icemaker operation After connecting the water supply, and setting your ice machine • Make certain water pressure is at least 20 psi and no more in place plug the power cord into the wall receptacle. Then than 120 psi and the water is turned on.
USING YOUR FREEZER Turning on the freezer After setting the freezer in place, leveling (see page 3), plug the power cord into the wall receptacle. The freezer should start after plugging in. The temperature control is factory preset to a mid range setting.
(50.01cm) (10.01 to 25.43cm) 21-25/32” (55.32cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS,15CM SOLID DOOR Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. Power outlet can be located in the back wall behind unit. Add 1”...
Manual defrost. Product Temperature versus Air Temperature 15CM Features Air temperature moves up and down with door openings and Can be installed on the counter top or built in. compressor run and off cycles. Air has little thermal mass and Makes crescent shaped ice cubes.
CARE AND CLEANING Condenser Air Flow Defrosting Instructions 15CM and 25CM The machine compartment located beneath the cabinet does Push the rocker switch located in the front grille to the not require frequent cleaning; however, satisfactory perfor- “OFF” position. mance depends on adequate ventilation. Be sure nothing ob- Remove the ice bucket and place a towel in the lower front structs the required air flow openings in front of the cabinet.
TROUBLESHOOTING YOUR ICE MACHINE Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting Electrocution Hazard - Never attempt to repair or perform main- guide below. Locate the problem in the guide and refer to the tenance on the unit until the main electrical power has been cause and its remedy before calling for service.
TROUBLESHOOTING YOUR ICE MACHINE OR FREEZER Problem Possible Cause Remedy Unit too warm or too cold inside. • Control set too warm or cold. • Adjust temperature colder or warmer as required. Allow 24 hours for tem- perature to stabilize. •...
OBTAINING SERVICE If Service is Required: • If the product is within the first year warranty period please call AGA MARVEL Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, AGA MARVEL Customer Service can provide recommendations of service centers in your area.
COMMERCIAL PRODUCT WARRANTY Nor do the above warranties cover failure of this product or its Entire Product - One Year Parts and Labor Warranty components due to: AGA MARVEL warrants to the original purchaser that it will sup- ply all necessary parts and labor to repair or replace in the end •...
Page 21
www.marvelscientific.com P.O. Box 400 1260 E. VanDeinse St. Greenville MI 48838-0400 800.223.3900 All specifications and product designs subject to change without notice. Such revisions do not entitle the 41011870-EN Rev A buyer to corresponding changes, improvements, additions, replacements or compensation for previously 12.22.09 purchased products.
Need help?
Do you have a question about the 15CM and is the answer not in the manual?
Questions and answers