Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Chargesplit WB132H
- Page 1 User Manual ChargeSplit DOMUS WB132H WB332H WB132P WB332P Chargesplit English...
-
Page 2: Table Of Contents
Content 1. Security Notes 2. Legal Notes 3. Safety instruction 4. Installation Instructions 5, Electrical protections device 6. Drilling and securing to wall 7. Pole installation 8. Wiring 9.Load Balancing probe 10. Introduction to charger 11. Setting up Bluetooth or WiFi Connection 12. -
Page 3: Security Notes
Security Notes The user must read and fully understand the safety instructions provided. Disregard of or actions contrary to the safety information and instructions contained in this manual and printed on the device may lead to electric shock, fire and/or severe injury and either damage to the vehicle or to the charging device. -
Page 4: Safety Instruction
Safety Instructions Do not operate if physical INSTALLATION MUST defects such as cracking, BE CARRIED FROM breakage, corrosion, PROFESSIONAL or other damage are ELECTRICIANS ONLY. observed. In case this happens, shut down the device and contact support immediately. Protect your device from Only an authorized any impact which it may be personnel may open,... - Page 5 Safety Instructions Never use a damaged process and the duration of charging cable, the vehicle unlocking may vary. plug, or the infrastructure electrical outlet to charge. Some vehicles can be started with the charging Never use contacts that are cable connected. Be sure to dirty or wet.
-
Page 6: Installation Instructions
Installation Instructions Installation must be performed by professional electrician only in accordance to local law and regulations. Non-professional or non-law conforms installations can be cause of fire, electrical shocks and even death. PRE-REQUIRSITES: The power supply connection must conform to local law and dimensioned for the power you intend to apply to the device. -
Page 7: 5, Electrical Protections Device
Electrical protections device The device can is equipped with over temp, and over amps protection. Over Amps is dynamically triggered based on Selected power +2A. This means, as example, that If a 16Amps charging power is selected the device will stop charging if power run above 18 amp. The maximum PCB temperature is 75°. -
Page 8: Drilling And Securing To Wall
Drilling and securing to wall Use included fishers and below mouonting schema attached mounting holes schema and included Pole Installation Special mounting accessory can be provided both for vertical and horizontal pole installation with matched device color. Please contact us for additional details... -
Page 9: Wiring
Wiring After the device has been fixed to wall or pole it’s time for wiring to the electrical line, the device it’s equipped with 1 meter connetion cable and , as stated before, has to be equiped with protection device. Connect EARTH (yellow/green) - NEUTRAL (blue) - L1 (brown) if 1P Connect EARTH (yellow/green) - NEUTRAL (blue) - L1 (brown) - L2 (black) - L3 (gray) -
Page 10: Introduction To Charger
Introduction to charger There are 2 main way to identify the charger status: OLED LED ring Display on button The OLED display report the status of the charger and many useful information regarding the charging process as total charged kWh, voltage, temperature, amperage and, if available, the house consumption to calculate load balancing. - Page 11 CHARGING: The charging process is active. The display will report “CHARGING” status and the led ring will pulse BLUE. You can stop the charging process directly from your car if necessary. If Load balancing is active led ring will pulse BLUE/ WHITE if solar balacing is active led ring will pulse BLUE/YELLOW VENTILATION: The car requires ventilation.
-
Page 12: Setting Up Bluetooth Or Wifi Connection
With the device totally turned OFF maintain the central button pressed Without releasing the button, power up the device until the display will show “CONNECT TO CHARGESPLIT WIFI” and the button start flashing in RED-GREEN-BLUE You can now release the button. A new Wi-Fi network called CHARGESPLIT has been created. - Page 13 Bluetooth mode Click on “Configure Wifi” to configure Wi-Fi connection. Available Wi-Fi networks will be scanned. Hint: if portal does not open try to remove ”Chargesplit” from known network or try open browser after network is connected...
- Page 14 After available network has been scanned just select your Wi-Fi network, insert password and click on SAVE. The device will reboot and, if password is ok, will connect to Wi-Fi network. Only 2.4Ghz Wi-Fi networks are supported. If, after reboot, the device remains in Connecting Wi-Fi repeat the configuration process.
-
Page 15: Configuring The Device In The App
Configuring the device in the APP After the device has been connected Wi-Fi configured in Bluetooth mode is time to add the device in the app. Configuration is automatic and based on the qrcode adhesive on side of your stations After registration you will find in the main menu. - Page 16 Click on the qr code icon and start to scan the qrcode adhesive on the side of your charging station. If qrcode is valid a new window will ask you about how your charing station is configured. (WiFi or Bluetooth) Select then the Operational mode (Wi-Fi or Bluetooth).
-
Page 17: Controlling Device From The App
Controlling device from the APP You have several options to control and real- time monitor the device from menu: Device Serial Number Realtime power in Amps Realtime temperature at pcb level Realtime Voltage If scheduled charging, the charging timeframe If Load / Solar Balancing is active, the real-time house consumption / Solar inverter AC generation... - Page 18 NEVER EXCEED YOUR WIRING CAPACITY, THIS CAN CAUSE SHOCKS, FIRE AND EVEN DEATH Pause /Resume if charging is active, you can remotely pause and resume the charging process. IMPORTANT: CHARGING PROCESS CAN’T BE STOPPED FROM APP. Must be stopped by car or by chargepoint button if “stop charge by button”...
-
Page 19: Settings Menu
Settings Menu Electricity cost €/kWh Use this setting to set the electricity cost. This will be used as base value to calculate costs in statistics Bluetooth WiFi Working Mode Change the working mode from Wi-Fi to Bluetooth. Warning: To change working mode you need to be connected to the device and the device need to be already configured for Wi-Fi access. - Page 20 Load Balancing Activate or deactivate load balancing: When active Device power will adapt automatically based on your house consumption. Load balancing is based on measurements from the provided load balancing coil. The Coil should be connected via the 3.5mm jack and attached to main house rail as per instructions to work.
-
Page 21: Scheduled Charging Menu
Scheduled charging menu It is possible to start the charging process at a specific time. This is done from the charging menu. Select the starting time at the charge icon (1) and end time at the finish line icon (2) Be sure to select “Active”... -
Page 22: Statistics
Statistics If device is connected to Wi-Fi statistics menu will take care of consumptions and costs. Statistics are divided on Week, Month, year base. The calculated prices are based on the €/kWh costs in the settings menu Live house consumption statistics to last 3 hours approximately. - Page 23 Wi-Fi monitor monthly consumptions and costs. Chargesplit Home is V2G/V2H ready with expansion slot for HPGP technology and ISO15118 stack. It can also been used in professional environments with OCPP 1.6JS protocol and our OCPP SAAS...
- Page 24 Supported OCPP call: for ocpp models (R and S series) refer to specific manual - Authorize - BootNotification - Data Transfer - MeterValues - HeartBeat - StartTransaction - RemoteStartTransaction - StopTransaction - RemoteStopTransaction - Reservation - Status Notification - Reboot - Reservation - Cancel Reservation - ChangeAvailability...
- Page 25 Specifications HOME (mod.W/P) OCPP (mod. R/S) Model Power Up to 7.4kW 1P or 22kW 3P Up to 7.4kW 1P or 22kW 3P Material ABS UL94-V0 ABS UL94-V0 Color Charcoal Grey / White Charcoal Grey / White Charging Mode 61851-1 Mode 3 Mode 3 Bluetooth / Wi-Fi 2.4 Ghz / HPGP Connectivity...
- Page 26 *RCCB type A or B can be required to match local law requirements. ALWAYS verify with your local installer **A second RCCB CA 30ma must be installed before station even if internal RCCB is installed. Type B residual current monitor is optional on WB132H/WB332H and inclued in all other models APP Features Android / iOS...
- Page 27 Dimensions...
- Page 28 Keep enviroment clean! Support In case of additional support please contact us to: support@chargesplit.com visit www.chargesplit.com Any information or caratheristic reported in this manual can vary in any moment with no notice to the user...