Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for SUG AWI Series
- Page 1 AWI Series DIGITAL TORQUE WRENCH PRODUCT INFORMATION MANUAL...
-
Page 2: Important Safety Rules
THANKS FOR CHOOSING THIS PRODUCT SUG Tools provide you with products at an affordable price, and we would like you to be fully satisfied with this product and our technical support. If any help or advice is needed, please kindly contact us. - Page 3 POWER TOOL USE AND CARE CAUTION For hand use only. Do not apply excessive torque or force to the tool housing. The torque only applies on the driver head. Do not shake or shock. Never use this digital torque tool to loosen fasteners. This digital torque tool is for hand use only.
-
Page 4: Functional Description
FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS: 1. Reversible Ratchet 2. Quick Release Button 3.Forward and reverse selection lever 4.1/4" / 3/8" 1/2"/Square Drive 5.Battery Cover 6.Handle 7.LED Indicator 8.Buzzer 9.LCD Panel 10.Button 11.Power/Reset Button 12.Unit Selection Button 13.Mode Selection Button 14.Up Button 15.Down Button 16.Torque Value Display 17.Mode Display (*1) -
Page 5: Specifications
SPECIFICATIONS Model (without AWI-10 AWI-30 AWI-60 AWI-100 communication) Minimum division 0.01 value Maximum operating 10N.m/7.37ft.lb/8 30N.m/22.12ft.lb/ 60N.m/44.25ft.l 100N.m/73.7ft.lb/ range 8.50in.lb/101.97k 265.5in.lb/305.91 b/531.04in.lb/61 885.0in.lb/1019.7 gf.cm kgf.cm 1.82kgf.cm kgf.cm （N.m） Connector（inches） 1/4 inches 3/8 inches 1/2 inches Setting range of 0.3~10N.m 0.9~30N.m 1.8~60N.m... - Page 6 ASSEMBLY BATTERY INSTALL AND REPLACEMENT 1. Open battery cover. 2. Insert battery cells, make sure the polarity is correct. 3. Close the battery cover. If doing the replacement, then do it reversely.
-
Page 7: Operation
NOTE Remove the batteries if stored for a long period of time. Keep spare batteries on hand when going on a long trip or to cold areas. Do not mix the type of batteries or combine used batteries with new ones. Sweat, oil and water can prevent a batteries’... - Page 8 POWER ON Press P/C key to turn the digital torque tool on. After the display showed the Max measuring value for 3 second, the display will show the last Data before it was switched off. POWER OFF Press P/C key and hold for 2 seconds to switch off . RESET Press P/C key to reset.
-
Page 9: Led & Buzzer
After setting a preset value (assuming the value is 5N.m), the force applied by the wrench will gradually increase from Minimum measure value. When force is applied, the displayed value will change as the user applies different amounts of force; the reading will increase as force increased, and decrease as force decreased. -
Page 10: Power Saving Mode
In order to get accurate data, press P/C key each time to reset the data before using the device. POWER SAVING MODE The device will be entered into power-saving mode after 2 minutes without any operation, you can press P/C key to wake it up. OVERLOAD WARNING Switch on or reset when screen continued to appear 120%, it means the device have been forced exceeds the maximum standard torque value 120%, may result in the... -
Page 11: Maintenance
WARNING NOTE FOR USING BATTERIES Please take out the batteries, if the product is not used a long period of time. Please prepare the more backup batteries, when the product is used in other places without electric power. Do not mix old and new batteries. Do not use the soiled batteries with perspiration and greasiness. -
Page 12: Protecting The Environment
19. Do not use the additional tools to extend the length of the handle, such as: iron or plastic pipe. 20. Do not touch any button when torque is exerted. 21. The digital torque wrench cannot be applied to the conductive tools. LUBRICATE The wrench’s internal mechanism is permanently lubricated during assembly.
Need help?
Do you have a question about the AWI Series and is the answer not in the manual?
Questions and answers