Tapcon HS22 Operator's Instruction & Training Manual
  1. Manuals
  2. Brands
  3. Tapcon Manuals
  4. Power Tool
  5. HS22
  6. Operator's instruction & training manual

Tapcon HS22 Operator's Instruction & Training Manual

Hammer actuated strike tool
Hide thumbs
Table of Contents

Advertisement

Quick Links

THIS TOOL IS FOR USE ONLY BY LICENSED OPERATORS.
YOU MUST OBTAIN A LICENSE BEFORE USING IT. A TOOL
OPERATOR'S CARD WILL BE ISSUED TO YOU AFTER
SUCCESSFULLY COMPLETING THE ENCLOSED EXAM AND
RETURNING IT TO RECEIVE YOUR CARD AND ACTIVATE
YOUR WARRANTY.
• The Tapcon HS22 is a light duty tool designed for applications such as small
room additions and basement remodels. Tool life will vary depending on work site
conditions and application.
• HS22 is a low velocity piston type fastening tool. It is designed for use with Tapcon
.22 caliber powder loads and Tapcon Drive Pins.
• Do not operate the HS22 before studying this manual carefully and thoroughly
understanding the material contained herein.
• Not for use with Tapcon screw anchors
IMPORTANT: The tool warranty is only activated upon receipt by ITW Brands of the
completed Operator's Exam.
MANUAL PRINTED IN CHINA
Operator's Instruction &
Training Manual
Part #12286
Rev. 07/21

Advertisement

Table of Contents
loading

Related Manuals for Tapcon HS22

Summary of Contents for Tapcon HS22

  • Page 1 Tool life will vary depending on work site conditions and application. • HS22 is a low velocity piston type fastening tool. It is designed for use with Tapcon .22 caliber powder loads and Tapcon Drive Pins.

  • Page 2: Warranty

    WARRANTY ALL WARRANTIES OF THE PRODUCTS DESCRIBED HEREIN, EXPRESSED OR IMPLIED, INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSES ARE SPECIFICALLY EXCLUDED, EXCEPT FOR THE FOLLOWING: ITW BRANDS WILL REPAIR OR REPLACE AT ITS SOLE OPTION ANY TOOL PART OR FASTENER WHICH WITHIN 6 MONTHS AFTER SALE BY ITW BRANDS IS FOUND BY ITW BRANDS TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP, NORMAL WEAR AND TEAR EXCLUDED.

  • Page 3: Safety Precautions

    - the fastener or piston can seriously injure your hand in the event of an accidental discharge. 2. Always use only Tapcon fasteners and loads at all times for consistent tool functioning. 3. Operators and bystanders must wear eye and hearing protection at all times.
  • Page 4 Failure to properly NOTE: Tapcon loads are designed for use with test fire to determine correct power level Tapcon tools. Do not attempt to use other power may result in overpowering the fastener, loads. Doing so may lead to unintentional load discharge as well as damage to the tool.
  • Page 5 SAFETY PRECAUTIONS Operating the Tool 1. Always point the tool away from people and in a safe direction. 2. Never use tool when explosives or flammable materials are nearby. 3. Never fire the tool without a fastener. The piston will protrude from the muzzle of the tool, enter the work surface and possibly cause injury to the operator or a bystander.
  • Page 6 SAFETY PRECAUTIONS 7. Never fasten into structural steel base STEEL CONCRETE material thinner than 3/16". Never fasten into concrete base material thinner than 3 times shank penetration. Always maintain minimum penetration requirements. 8. Fastening into block and masonry is not recommended.

  • Page 7: Operating Problems

    SAFETY PRECAUTIONS 2. Never carry fasteners or other hard objects in the same pocket or container with powder loads. The loads could be set off, causing serious injury or death. 3. A person that is color blind must be extra careful when loading the tool.
  • Page 8 Immediately store a jammed or broken tool in a locked container after tagging it "Defective - Do Not Use". Call 1-877-489-2726 for technical assistance. TAPCON FASTENER SELECTION GUIDE .300 Head Plastic Fluted Drive Pins .300 Head Plastic Fluted Drive Pin with 7/8" Washer...

  • Page 9: Tool Operation

    TOOL OPERATION CAUTION! Be sure to read and understand all safety precautions and complete the Operator's Exam before attempting to operate the tool. Check to be sure the tool is unloaded and no foreign objects or fasteners are in the barrel. Perform daily function test before operating. OPERATION Check the functioning of the tool, without a powder load or fastener in the tool, by pushing down against the work surface, checking to be sure the groove portion of the...

  • Page 10: Thorough Cleaning

    TOOL OPERATION 4. Close tool by pulling the barrel back to the Semi-close semi-closed position. Never attempt to close position the tool by exerting force on the front of the barrel. Never place your fingers or hands over the muzzle end of the barrel. The proper position of the hands and fingers are shown in the illustration.

  • Page 11: Troubleshooting

    TROUBLESHOOTING Tool operator must carefully follow all operating instructions and precautions to successfully operate the tool. Following is a list of potential situations an operator may encounter and the probable causes: • If a tool problem occurs and technical assistance is required, please call 1-877-489-2726 WARNING: Do not operate a tool that is not functioning properly.
  • Page 12 TROUBLESHOOTING PISTON OVERDRIVE TO AVOID PISTON OVERDRIVE Piston overdrive is a problem that occurs after • Decrease power level. Note: the tool is fired. The piston may extend into the Always make test fastenings work surface as much as 1/2". Piston overdrive with lightest load and increase until proper level is found.
  • Page 13 APPLICATIONS Wood to Concrete 7/8" washer provides a greater bearing surface to the wood member, minimizing uplift. Wood to Steel Fastener should penetrate steel completely for maximum holding power. Furring Strip to Concrete or Masonry Walls When fastening into masonry, shoot into horizontal joints only.

  • Page 14: Permanent Installation

    HOW TO SELECT A POWDER ACTUATED FASTENER DETERMINE FASTENER TYPE Drive pins are used to directly fasten an object (permanent installation). Threaded studs are used where the object fastened may later be removed or where shimming is required. The following shows how to determine shank and thread length: PERMANENT INSTALLATION 1A To Concrete 1B To Steel...
  • Page 15 ■ ■ tile, brick and thin sheet metal are examples of materials not to be fastened into. 15. It is not necessary to read the Operator's Manual prior to operating the HS22 low velocity powder True False ■ ■ ■...
  • Page 16 LICENSE AND WARRANTY ACTIVATION The HS22 is warranted for 90 days after sale by ITW Brands. I certify that I have read and understand the HS22 Operator's Instruction and Training Manual and have taken the Operator's Exam on the reverse side.

Table of Contents