Taili 813B Instructions Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

MODEL

813B

FOR YOUR SAFETY:

READ ALL INSTRUCTIONS CAREFULLY

Table of Contents

Need help?

Do you have a question about the 813B and is the answer not in the manual?

Questions and answers

Summary of Contents for Taili 813B

Page 1 MODEL 813B FOR YOUR SAFETY: READ ALL INSTRUCTIONS CAREFULLY...
Page 2: Table Of Contents
Table of Contents General safety instructions for Power Tools…………………………………………1 Main specification…………………………………………………………………………2 Unpacking and checking contents…………………………………………………… 2 List of loose parts in the box and bags………………………………………………. 3 Getting to know your drill press………………………………………………………..4 Assembly………………………………………………………………………………….. 5 Lubrication………………………………………………………………………………… 6 Maintenance……………………………………………………………………………… 6 Wire diagram……………………………………………………………………………… 7 Trouble shooting………………………………………………………………………….
Page 3: Main Specification
Main Specification Drill Capacity 16mm / 5/8 in. Chuck Capacity 13mm / 33/64 in. Sewing 200mm / 8 in. Spindle Taper JT33 Distance,Spindle to column 102mm / 4-1/64 in. Max.Spindle travel 50mm / 1-31/32 in. Max.distance chuck to table 165mm / 6-1/2 in. Max.distance chuck to base 245mm / 9-41/64 in.
Page 5: List Of Loose Parts In The Box And Bags
List of Loose Parts in the box and bags...
Page 7: Getting To Know Your Drill Press
Getting To Know Your Drill Press - 4-...
Page 8: Assembly
Assembly Refer to the figure install all parts correctly, tighten the screw and bolts securelly. 1 Table Support 2. Support Lock handle 3 Column 4 Base 5 Support Column 6 Screw Hex Hd M8x20 7 Table Bevel Lock Screw 8 Table 9 Head Asm - 5-...
Page 9 - 5-...
Page 12: Lubrication
Lubrication All of the BALL BEARING are packed with grease at the factory.They require no further lubrication. Periodically lubricate the table elevation machanism,the SPLINES (grooves) in the spindle,and the RACK (teeth of the quill),see "Getting to know your drill press." Maintenance Frequently blow out any dust that may accumulate inside the motor.
Page 13: Trouble Shooting
Trouble Shooting TROUBLE PROBABALE CAUSE REMEDY 1.Incorrect belt tension. 1. Adjust tension. 2.Dry Spindle. 2. Lubricate spindle. Noisy Operation 3. Checking tightness of retaining nut on 3.Loose spindle pulley pulley,and tighten if necessary. 4.Loose motor pulley 4.Tighten setscrews in pulleys. 1.Incorrect speed.
Page 15: Repair Parts
Repair Parts FIGURE1 Description Description Bushing-Ruber Bearing-Ball 17mm Knob Spacer Screw-Pan Hd.M5x0.8-1.2 10 Insert-Pulley Belt-"V"5/16x26 11 Pulley-Spindle Guard w/Labels 12 Nut-Pulley Screw-Washer Hd. 13 Clamp-Cord M6x1.0-1.6 14 Screw-Pan Hd.M5x0.8-16 Ring Retaining 15 Washer,Foam...
Page 16 Repair Parts FIGURE2...
Page 17 FIGURE2 Description Description Head w/Roll Pin & Trim Box-Switch w/Depth Scale Nut-Lock M8x1.25-8 Screw-Pan Cr. M5x0.8-12 Washer Switch-Locking Screw-Hex M8x1.25-25 Screw-Selt Tapping Pan Pulley-Motor Hd.N4x16-8 Screw-Hex Soc.Set M6x1.0-10 Cover-Switch Plate Motor Key-Switch Stop-Motor Connector-Wire Spring-Motor Stop Seat-Spring Knob-Motor Adjustig Retainer-Spring Screw-Hex Soc.Set M8x1.25-8 Spring-Tension Knob...
Page 18 Repair Parts FIGURE3 FIGURE4 Key No. Description Key No. Description Gasket-Quill Support-Table w/Scale Bearing-Ball 12mm Support-Lock Handle Tube-Quill Tube/Support Screw-Pan M5x0.8-20 Base Collar-Stop Screw-Hex Hd.M8x1.25-20 Ring-Retaining Screw-Hex Hd.1/2-12x7/8 Shaft-Pinion Table Chuck Key-Chuck Nut-Hex M6x1.0 Nut-Hex M5x0.8 Rod-Stop...
Page 19 FIGURE4 PARTS LIST Description Description knob-Motor Adjusting Seat-Spring Screw-Socket Set M10*1.5-12 Retainer-Spring Handle-Belt Tension Spring-Torsion Pin-Stop Cap-Spring Ring-Depth Stop W/Scale Nut-Hex M12*1.5-8 Lock-Depth Screw Head w/Pointer and Trim Tie-Wire Guide Scale Cord-Power w/Plug Knob Clamp-Cord Support-Motor Bracket Lock-Washer-Ext M5 Screw-Hex HD M6*1.0*12 Screw-Pan HD M5*0.8-8 Washer 8*16*1.6 Box Switch...