◆◆◆ table of contents ◆◆◆ 1.Before using ・・・1 2.Name of parts ・・・3 3.Operating Instruction(How to adjust each part) (1)How to skive ・・・4 (2)Thickness adjustment・Presser foot handle set ・・・4 (3)Adjustment of presser foot angle(Diagonal skiving method)・・5 (4)How to replace presser foot ・・・5 (5)Blade replacement ・・・6...
1.Before using ■Safety Precautions■ ◆ Read this "Safety Precautions" carefully before use. ◆ After reading, keep where you can see at any time. WARNING Risk of death or serious injury form improper use. ⚫ Use only AC 100V-240V. ⚫ In the following cases, turn off the power switch and unplug. ☑When leaving the machine.
Page 4
■Handling Instructions■ ⚫ Do not burden the machine.(extremely thick or hard) ⚫ Do not use where it gets wet. Avoid using wet hands. ⚫ Be careful not to touch the cutting edge when replacing blade. ⚫ Keep your fingers away from the blade while operating. ⚫...
3.Operating Instruction(How to adjust each part) (1)How to skive ① Turn on the main power on the back of the machine.(When the power is on, the indicator lamp lights up in green.) ② Adjust the guide to the desired width. ③...
( 3 ) Adjustment of presser foot angle(Diagonal skiving method) ① Replace with the 20 mm width plastic presser foot included in the accessories. ※The 20mm wide presser foot is already 15 ° angled compared to the 40mm one. ② When turning the angle adjustment screw left or right, changes the distance between the presser foot and the blade and adjust to any angle, fix firmly with lock nut.
( 5 ) Blade replacement ① Turn off the main power. ② Loosen the screw of the guard with the accessory driver, remove the guard. ③ Loosen the blade fixing screw with the accessory driver, remove the blade holder. ④ Replace the blade and assemble in the reverse process. (Precaution) ・Work carefully not to touch the cutting edge.
( 7 )Position adjustment of spring tension adjustment lever ① When a hard workpiece is skived Pull the spring tension adjustment lever forward and hang in the back groove, strengthen the force of the spring. ② When a soft workpiece is skived Hang in the front groove of the spring tension adjustment lever, weaken the force of the spring.
( 9 ) Fuse replacement ① Turn off the main power and unplug the power cord. ② Pull out the fuse holder of the power jack. ③ Replace a new fuse, assemble in the reverse process. Use a commercially available 5A, 250V miniature glass tube fuse.(φ5.2×20mm) ➢...
Switching operation Operation Behavior Press the run switch Start operation Set the back switch to the run switch Press the foot pedal No reaction Press the run switch No reaction Set the back switch to the foot pedal side Press the foot pedal Start operation (...
Page 12
4. Abnormality of machine and its cause and adjusting method Abnormality Cause Adjusting method The up and down space between presser Thin the skiving thickness, because it is too thick foot and the blade is wide The space between the feed roll and the Bring the feed roller as close to the blade as blade is wide possible...
Page 13
Abnormality Cause Adjusting method The space between presser foot and the Thick the skiving thickness, because it is too thin blade is narrow The presser foot is below the blade edge Raise the presser foot The space between the feed roll and the Work piece goes under the Bring the feed roll closer to the blade blade is too wide...
5.Specifications M O D E L NP-S7B AC 100V – 240V Po we r sou rce 50/60Hz R a t e d f r e q u e n c y P o w e r c o n s u m p t i o n 15min R a t e d t i m e...