Fortior Tech FU68 Series User Manual

Mcu writer

Advertisement

FU68XX Series MCU
Writer User Manual
Fortior Technology(Shenzhen) Co.,Ltd.
Room203,2/F,Building No.11,Keji Central Road 2,Software Park,
High-Tech Industrial Park, Shenzhen,P.R.China
Tel:86-755-26867710
Fax:86-755-26867715
Contained herein
Copyright by Fortior Technology(Shenzhen) Co., Ltd all rights reserved.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FU68 Series and is the answer not in the manual?

Questions and answers

barclais
January 16, 2025

bjr comment peut on sauvegarder un programme du mcu fu 6832 a partir de ce programmeur

Subscribe to Our Youtube Channel

Summary of Contents for Fortior Tech FU68 Series

  • Page 1 FU68XX Series MCU Writer User Manual Fortior Technology(Shenzhen) Co.,Ltd. Room203,2/F,Building No.11,Keji Central Road 2,Software Park, High-Tech Industrial Park, Shenzhen,P.R.China Tel:86-755-26867710 Fax:86-755-26867715 Contained herein Copyright by Fortior Technology(Shenzhen) Co., Ltd all rights reserved.
  • Page 2: Preface

    Preface This is FU68XX Series MCU Writer User Manual. In this paper,quality inspectors and users can learn how to configure the software to write and produce FU68XX series MCU(needed to operate with our company's dedicated writer) .In addition,there are some brief introductions to the software and hardware configuration.
  • Page 3: Table Of Contents

    Contents Preface ..............................2 Contents ............................. 3 Offline Writer Introduction ......................4 1.1 Hardware abstract ........................4 1.2 Software Configuration ......................6 1.2.1 App Area Setting......................6 1.2.2 Writer UI ........................7 1.2.3 Hardware Setting......................7 1.2.4 Device Enumeration ....................7 1.2.5 Download Procedure ....................
  • Page 4: Offline Writer Introduction

    1 Offline Writer Introduction 1.1 Hardware abstract The hardware configuration is as the figure shows below: Chart 1-1-1 Rev_V1.8 4 / 20 www.fortiortech.com...
  • Page 5 chart 1-1-2 The above picture is only for reference, specific parameters are listed below: Item Index Function Remark USB data lines LCD display panel 1:On-line(Default); 0:Off-line Online/Offline switch SW1 switch to low default Mode selection switch SW2 Related to SW3,See tab 1-2 Mode selection switch SW3 Related to SW2, See tab 1-2 Mode selection switch SW4...
  • Page 6: Software Configuration

    1.2 Software Configuration 1.2.1 App Area Setting Decompress the offline writer from the package named FTMcuOfflineWriter V1.0.1.rar,and then open the folder of FTMcuOfflineWriter V1.0.1 , double click the Execution file G+CodePacker.exe with left key, switch setting option to the page of App Area ,See the following drawing: Chart 1-2-1 After Configured the item of App code, user may click”Pack”button, for a few...
  • Page 7: Writer Ui

    1.2.2 Writer UI Writer main UI is as the figure shows below: Chart 1-2-2 1.2.3 Hardware Setting Now user can make the switch to Online on the left of the writer, and then connect it to the PC machine with USB data line. If user does this, the hardware will enter the online download mode, the hareware connection graph is shown as the following: Chart 1-2-3 1.2.4 Device Enumeration...
  • Page 8: Download Procedure

    1.2.5 Download Procedure Now user can click“Start Download”button on the software tool, after that, the software tool will begin to execute this download action, the whole download procedure is shown as the below figure: Chart 1-2-5 if it finished downloading , please close this software tool. Rev_V1.8 8 / 20 www.fortiortech.com...
  • Page 9: Operation Introduction

    1.3 Operation Introduction 1.3.1 Power on again User may switch to the offline write mode after they have finished task of online download, the detailed steps are shown as the below: first plug out USB data line to make device power off ...
  • Page 10 Chart 1-3-2 Chart 1-3-2-1  Observe the device doing task status on the LCD panel Chart 1-3-2-2  Observe the status of the LED light Rev_V1.8 10 / 20 www.fortiortech.com...
  • Page 11: Crc Verify Mode

    Green light ----- Success , Red light------Fail or haven’t adjust frequency, Orange light---- ----User does not put IC into socket In addition,in order to prevent omitting to write,the writer is added with the lid open detection function after successful writing.If the blue light is on,it means user opens the lid after writing,or puts IC back in Socket without pressing RUN Key.
  • Page 12: Erase Mode

    should keep High; Or in Write Mode,switch SW2 and SW3 to High, then enter Verify Mode  Power on,enter the CRC Verify Mode  Put the IC of FU68xx series into Socket,and make sure it is in good contact  Observe the device doing task status on the LCD panel Chart 1-3-3 1.3.4 Erase Mode...
  • Page 13: Online Writer Introduction

    2 Online Writer Introduction This Online Writer is a USB-based mass production tool.Currently,four FU68xx series IC can be mounted at the same time for writing.And the corresponding follow-up will extend to 8 or more. 2.1 Hardware Configuration 2.1.1 Hardware Abstract Refer to chapter 1.1, since the same hardware is used to both Online and Offline Writer.
  • Page 14: Software Configuration

    2.2 Software Configuration 2.2.1 Writer UI Decompress FTMcuMassProductionTool V1.0.0.4.rar,and double click the exe file.Writer UI is shown as below: Chart 2-2-1 Item Index Function Remark Setting button Configure the Write Procedure Start Download button Write IC Enum Device button Enum device Dev Numbers The number of displayed devices(Max:16) Device List...
  • Page 15: Script Configuration

    2.2.3 Script Configuration This configuration item is mainly used in the R&D phase rather than the production phase.For mass production operators,they do not need to care about this configuration.  R&D Phase: The R&D staffs only need to care about Step4,and select the bin file developed with Keil .Click the “OK”button to confirm.Other steps can be ignored.The special configuration is shown as below: Chart 2-2-3...
  • Page 16: Download Procedure

    2.2.4 Download Procedure After setting, user can go back to the main UI to write files.Now user can click “Start Download”button on the software tool.After that,the software tool will begin to execute this download action. The whole download procedure is shown as the below figure: Chart 2-2-4 If writing fails,the corresponding device list will be displayed in red font.At the same time,user can double click corresponding device list,and then the corresponding log will pop...
  • Page 17: Extand Io Port Write

    3 Extand IO Port Write 3.1 Product Write When user has attached MCU to the new product board and the whole hardware is in good status ,they can connect the product board to the PC to write. In addition,when connecting VDD to the product board,user need not to supply VDD5.The Writer will aotumatically send out VDD5 as needed.
  • Page 18 Specific pin definition is shown as below: Table 3-1 Pin Name Direction Description Output Connect to VDD5 pin at IC to be write Inout Connect to FICEK pin at IC to be write Inout Connect to FICED pin at IC to be write Earth ware Press the RUN key to write/verify/erase, and the light turned green when write success, or red light when write fail.
  • Page 19: Machine Automatic Write

    3.2 Machine Automatic Write The seven signal lines for Machine automatic writing is shown as below: Chart 3-2-1 Success status: Chart 3-2-2 Rev_V1.8 19 / 20 www.fortiortech.com...
  • Page 20 Fail status: Chart 3-2-3 The detail of pin is shown as below: Table 3-2 Pin Name Direction Description Connection Module Output 5.5V operating Voltage SOCKET Inout Communication port, Connect to FICK pin at IC SOCKET Inout Communication port, Connect to FICD pin at IC SOCKET Earth ware SOCKET、MACHINE...

Table of Contents

Save PDF