Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for ElectroCraft EPS-HDM1004ECO
- Page 1 EPS-HDM1004ECO Encoder Modulator User Manual...
-
Page 2: Table Of Contents
About This Manual Intended Audience This user manual has been written to help people who have to use, to integrate and to install the product. Some chapters require some prerequisite knowledge in electronics and especially in broadcast technologies and standards. Directory CHAPTER 1 INTRODUCTION ....................... -
Page 3: Chapter 1 Introduction
Chapter 1 Introduction 1.1 Product Overview EPS-HDM1004ECO is a professional high integration device which includes encoding, multiplexing, and modulating in one box. It supports 4 HDMI inputs and DVB-C/T RF out with 2 adjacent carries and 2 MPTS out as mirror out of the 2 modulation carriers via DATA (GE) port. -
Page 4: Principle Chart
EPS-HDM1004ECO Encoder Modulator User Manual Encoding MPEG-1 Layer 2, LC-AAC, HE-AAC and AC3 Pass Through Sampling rate 48KHz Resolution 24-bit Audio Gain 0-255 Adjustable Audio MPEG-1 Layer 2 48/56/64/80/96/112/128/160/192/224/256/320/384 kbps bit-rate LC-AAC bit-rate 48/56/64/80/96/112/128/160/192/224/256/320/384 kbps HE-AAC bit-rate 48/56/64/80/96/112/128 kbps Maximum PID... -
Page 5: Chapter 2 Installation Guide
EPS-HDM1004ECO Encoder Modulator User Manual 1.5 Appearance and Description Front and Rear Panel Illustration 4 7 6 5 RF test and RF out port Port Power supply and Grounding Pole 4 HDMI inputs ASI out (Optional) Run and Power Indicators... -
Page 6: Power Precautions
EPS-HDM1004ECO Encoder Modulator User Manual power is on. After use, securely stow away all loose cables, external antenna, and others. 2.2 Power precautions When you connect the power source, make sure if it may cause overload. Avoid operating on a wet floor in the open. Make sure the extension cable is in good condition ... -
Page 7: Grounding Requirement
EPS-HDM1004ECO Encoder Modulator User Manual Wall It can be covered with wallpaper, or brightness less paint. Fire Protection Fire alarm system and extinguisher Requiring device power, air-conditioning power and lighting power are independent to each other. Device power requires Power AC 110V±10%, 50/60Hz or AC 220V±10%, 50/60Hz. -
Page 8: Operation
EPS-HDM1004ECO Encoder Modulator User Manual to confirm they are on the same network segment. I.G. the PC IP address is 192.168.99.252, we then change the device IP to 192.168.99.xxx (xxx can be 1 to 254 except 252 to avoid IP conflict). - Page 9 EPS-HDM1004ECO Encoder Modulator User Manual Parameters → → → → Encoder From the menu on left side of the webpage, clicking “Encoder”, it displays the information of each encoding channel from the encoder as Figure-3. General settings for the Encoding program: User can edit any item listed as needed.
- Page 10 EPS-HDM1004ECO Encoder Modulator User Manual Select the text color and background color Put your caption anywhere Enter your text here Set when to show caption. So do Logo and QRCode. Figure-5...
- Page 11 EPS-HDM1004ECO Encoder Modulator User Manual Input the QR code URL Put the QR code everywhere Browse and select the QRcode which has been created Figure-6 Parameters → → → → TS Config: From the menu on left side of the webpage, clicking “TS Config”, it displays the interface where users can configure the TS output parameters.
- Page 12 EPS-HDM1004ECO Encoder Modulator User Manual Figure-7 TS Config→ → → → Stream select: Clicking “Stream select”, it displays the interface where users can select program(s) to multiplex out and modify program info. (Figure-8) Input Area Output Area Operation Area Figure-8 Configure ‘Input Area’...
- Page 13 EPS-HDM1004ECO Encoder Modulator User Manual To select all the output programs Program Modification: The multiplexed program information can be modified by clicking the program in the ‘output’ area. For example, when clicking , it triggers a dialog box (Figure-9) where users can input new information.
- Page 14 EPS-HDM1004ECO Encoder Modulator User Manual TS Config→ → → → PID Bypass: From the TS Config menu on up side of the webpage, clicking “PID Bypass”, it displays the interface where users can enable PID Pass-through. (Figure-11) Figure-11 Parameters → → → → Modulator: Clicking “Modulator”, it displays the Modulator Configuration screen as Figure-12.
- Page 15 Encoder Modulator User Manual Figure-12 Parameters → → → → IP Stream: EPS-HDM1004ECO supports 2 TS to output in IP format through the DATA port. Clicking “IP Stream”, it displays the interface where to set IP out parameters (Figure-13). Channel Config Figure-13 When users click “pen”...
- Page 16 EPS-HDM1004ECO Encoder Modulator User Manual Figure-14 When users click “ASI Out” list, users can set MPTS 1, 2 as the TS out via ASI out. System → → → → Network: Clicking “Network”, it displays the interface as Figure-15 where to set network parameters.
- Page 17 EPS-HDM1004ECO Encoder Modulator User Manual Figure-16 System → → → → Configuration: Clicking “Configuration”, it displays the screen as Figure-17 where to save/ restore/factory setting/ backup/ load your configurations. Figure-17 System → → → → Firmware: Clicking “Firmware”, it displays the screen as Figure-18 where to update firmware for...
- Page 18 EPS-HDM1004ECO Encoder Modulator User Manual Figure-18 System→ → → → Date/Time: From the menu on left side of the webpage, clicking “Date/Time”, it will display the screen as Figure-19 where to set date and time for the device. Figure-19 System→ → → → Log: Clicking “Log”, it displays the log interface as Figure-20 where to check or export the...
- Page 19 EPS-HDM1004ECO Encoder Modulator User Manual Figure-20...
-
Page 20: Chapter 4 Troubleshooting
Device in damp environment Device was suffered from physical damage Longtime idle. After switching on and restoring to factory setting, device still cannot work properly. Maintenance needed Chapter 5 Packing List EPS-HDM1004ECO Encoder Modulator HDMI Cables 4pcs Power Cord...
Need help?
Do you have a question about the EPS-HDM1004ECO and is the answer not in the manual?
Questions and answers