Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for FITRE RETEMATIC IP-RMH1
- Page 1 IP-RMH1 RETEMATIC™ HEAD UNIT INSTALLATION & CONFIGURATION MANUAL...
- Page 2 Opening or removing covers that are marked with the triangular symbol with a lightning bolt can expose you to electrical shock. Only a trained service technician should service components inside these compartments. FITRE S.p.A is not responsible for any damages caused by improper use of this device Installation and Configuration Manual...
-
Page 3: Table Of Contents
ReteMatic™ Head Unit IP-RMH1 CONTENTS PRODUCT PRESENTATION........................4 Technical Specifications ........................... 4 Dimensional Drawings ..........................5 Connections.............................. 6 INSTALLATION ............................7 ReteMatic Network Architecture........................ 7 ReteMatic Network Planning........................9 Multi-Head ReteMatic Network ....................... 10 CONFIGURATION VIA WEB INTERFACE ....................11 Authentication page ..........................11 403 Error (forbidden) page........................ -
Page 4: Product Presentation
ReteMatic™ Head Unit IP-RMH1 PRODUCT PRESENTATION The ReteMatic™ Network Infrastructure has been designed to meet the application needs required by industrial and harsh environments by combining power and robust data communication over a single medium, the standard power cable. IP-RMH1 is a ReteMatic Head Unit, originating a ReteMatic bus to which up to ten Field Units can be connected. -
Page 5: Dimensional Drawings
ReteMatic™ Head Unit IP-RMH1 IMENSIONAL RAWINGS Installation and Configuration manual... -
Page 6: Connections
ReteMatic™ Head Unit IP-RMH1 ONNECTIONS FRONT SIDE REAR SIDE FRONT SIDE This RJ45 connector allow to interface the IP-RMH1 unit with a 10Base-T /100Base-TX Ethernet network REAR SIDE POWER IN This power connection provides power required to operate the unit and the external devices connected at the ReteMatic bus originated by this unit (“RETEMATIC OUT”... -
Page 7: Installation
WAN connections. In we can see an application example of ReteMatic Network (orange line), which is used to deploy a Fitre Astro Page&Talk VoIP Intercom and PAGA system in a Ex classified Petrochemical site. - Page 8 IP-RMH1 ReteMatic™ Head Unit ReteMatic Head Unit IP-RMH1 115VAC /230VAC Ethernet 115VAC/230VAC RJ45 + DATA ReteMatic Field Unit RMF50-Ex Ethernet 4 wires 24VDC SPEAKER ReteMatic Field Unit RMF50-Ex Ethernet 4 wires 24VDC & Audio 24VDC 115/230 VAC SPEAKER Beacon 24VDC &...
-
Page 9: Retematic Network Planning
ReteMatic™ Head Unit IP-RMH1 ATIC ETWORK LANNING For best performance, follow these guidelines when you plan your ReteMatic network: ReteMatic unit has to meet operating condition as specified in technical specifications U Plan your network to reduce interference from other electrical products that are in field, these appliances might prevent ReteMatic products from working correctly or reduce network performance se only approved ReteMatic devices, like the ReteMatic Head Unit IP-RMH1 and ReteMatic Field Units RMF50-Ex or RMF150B-Ex... -
Page 10: Multi-Head Retematic Network
ReteMatic™ Head Unit IP-RMH1 ReteMatic Head Unit (IP-RMH1) can supply a maximum current of 6A so maximum power consumption of all devices supply by ReteMatic is 690W with 115VAC or 1380W with 230VAC, please consider also the power dissipation of the cables. Loud- Total ReteMatic... -
Page 11: Configuration Via Web Interface
ReteMatic™ Head Unit IP-RMH1 CONFIGURATION VIA WEB INTERFACE The ReteMatic Head Unit can be configured by means of an internet browser through its Web Interface In order to access the Web configuration pages, it is necessary to know the unit’s IP address and to setup the PC to properly connect to it (e.g. -
Page 12: 403 Error (Forbidden) Page
ReteMatic™ Head Unit IP-RMH1 403 E RROR FORBIDDEN The 403 Error (Forbidden) Page is displayed when an unauthenticated user requests a Web page that requires authentication. 403 is the HTTP standard status code for a client error meaning ‘forbidden’. After five seconds, the Web browser is automatically redirected to the Main Page if the user is authenticated;... - Page 13 ReteMatic™ Head Unit IP-RMH1 Figure 5 - Web interface: Main page Basic settings In this section we can find: MAC address of the LAN interface of the unit • Device ID on the ReteMatic Network (automatically assigned during Network startup) •...
-
Page 14: Ip Network Configuration
ReteMatic™ Head Unit IP-RMH1 Neighboring Domain Interference Mitigation (NDIM) This functionality is intended to maximize the overall performance of ReteMatic network in presence of neighboring ReteMatic networks, through the coordination and isolation mechanisms. Once a neighboring domain is detected, a domain master takes all needed actions to mitigate interference with the neighboring domains’... -
Page 15: Ethernet Status
ReteMatic™ Head Unit IP-RMH1 THERNET TATUS The Ethernet Status page is reached by clicking on the “Ethernet” link on the left pane and shows the physical status of the LAN port of the unit. Figure 7 - Web interface: Ethernet Status EVICE NFORMATION The Device Information page is reached by clicking on the “... -
Page 16: Advanced Configuration
ReteMatic™ Head Unit IP-RMH1 Figure 8 - Web interface: Device information DVANCED ONFIGURATION The Advanced Configuration page is reached by clicking on the “ Advanced ” link on the left pane and allows to perform an Hardware Reset of the unit.. Hardware Reset To perform a hardware reset (cold reboot), click the Hardware Reset button shown below to reboot the unit and then wait until it completes its initialization. - Page 17 ReteMatic™ Head Unit IP-RMH1 Figure 9 - Web interface: Advanced Configuration Installation and Configuration manual...
-
Page 18: Monitoring A Retematic Network
ReteMatic™ Head Unit IP-RMH1 MONITORING A RETEMATIC NETWORK This chapter provides information to monitor the status of the ReteMatic network. Connect a PC to the ReteMatic Head Unit or to a switch that is connected to the ReteMatic Head Unit, the PC used must be configured with an IP address in the same subnet of the one assigned to the unit. -
Page 19: Troubleshooting
ReteMatic™ Head Unit IP-RMH1 TROUBLESHOOTING This section provides information to help you diagnose and solve problems that you might encounter. Connect a PC to ReteMatic Head Unit as described in “MONITORING A RETEMATIC NETWORK on page 18) and check if all nodes are visible in the Available Connections list: if one or more nodes are not found in this table, or if the Tx/Rx values are low or fluctuating, look for possible causes of Symptom Possible Cause... - Page 20 SINCE 1943 Certified DNV Italy CERT-00403-95-AQ-MIL-SINCERT F I T R E S.p.A. - electronics • telecommunications 20142 Milan • Italy • via Valsolda, 15 phone: (+39)02.8959.01 • telefax: (+39)02.8959.0400 e-mail: info@fitre.it • internet http://www.fitre.it Branch Offices in Roma and Venice...