Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Standa 1VIS10
- Page 1 P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt Vibration isolation system 1VIS10 User manual Standa 2018...
-
Page 2: Table Of Contents
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt Table of contents 1. General information 1.1. Introduction 1.1.1. Safety 1.2. Location of the table 1.3. Air supply requirements 2. -
Page 3: General Information
Operating temperature range Load-bearing capacity (at 6 bar) per isolator Fig. 1. Specification of 1VIS10 A specification of a pneumatic support is presented in fig. 1. Although each support is intended for a load of up to 160 kg, you should prevent overloads of the table at the edges, otherwise any one pneumatic support may become overloaded even if the total weight fits within the limits set. - Page 4 P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt Fig. 2. Level control, model 1LV-1WM * Optional. ** An overpressure relief valve can be provided. Precision of level setting: ± 0.3 mm.
-
Page 5: Safety
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt 1.1.1 Safety This manual uses certain terms that are important for your safety. Warning Used to denote a danger that may result in injury. -
Page 6: Mounting Of The System
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt The air supply system must be provided with a valve (plug) for a complete stoppage of air supply in the case of maintenance and/or resetting of the system, or in cases of major changes in loads of the system. -
Page 7: Connection And Installation Of Pneumatic Vibration Isolation Components
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt 2.1.3 Connection and installation of pneumatic vibration isolation components Insert the pipes, through the hole for air supply pipe, into the collet fittings until tight. Pull the pipes accurately to make sure that the connection is secure. -
Page 8: Fitting The Collector And The Support Plates
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt 2.1.4 Fitting the collector and support plates Attach the collector to the leg assembly by M5x30 screws. Insert the hex key 3HK-5 into the hole of the piston and hold it, so that the torque moment doesn’t transmit to the diaphragm. -
Page 9: Assembly Of The Table
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt 2.1.5 Assembly of the table Place the table accurately on top of the pneumatic supports. If you need to adjust the location of the table, lift the table over the supports. -
Page 10: Preparation Of The System For Operation And Vibration Isolation Of The Table
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt 2.2 Preparation of the system for operation and vibration isolation of the table 2.2.1 Assembly of level controls A level control is shown in fig. - Page 11 P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt Fig. 9. Installation of level control Fig.10. Installation of level control...
-
Page 12: Connection Of Air Supply Pipes
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt After placement of the three controls the system must look as shown in fig. 9. Fig. 11. Vibration isolation system 2.2.2 Connection of air supply pipes... -
Page 13: Setting Of Level Controls
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt If the table does not start to float in a few minutes, increase the air pressure, check whether the needle valve is open and try to adjust the position of the control lever by turning the control screw clockwise. -
Page 14: Management Of The System
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt 3. Management of the system 3.1 Main principles After completing the assembly of the system and once the table has emerged, minor changes may be introduced based on individual requirements for the system. -
Page 15: Maintenance
P.O. Box 2684 03001 Vilnius, Lithuania Phone: +370-5-2651474 Fax: +370-5-2651483 E-mail: sales@standa.lt Manufacturer of Opto-Mechanical equipment for research, industry and education http://www.standa.lt 3.3 Maintenance If operated correctly, the pneumatic vibration isolation system needs minimum maintenance. As a rule, the maintenance includes the assurance of the cleanliness of the air supplied, i.e. replacement of the filter and removal of any water.
Need help?
Do you have a question about the 1VIS10 and is the answer not in the manual?
Questions and answers