Table of Contents
Advertisement
Quick Links
PO-1775F
Before reading or using this manual be certain of the material of construction of your pump. Check the model
number label on the pump as follows:
POLYESTER
POLYPROPYLENE
RYTON
NORYL
Verify the chemical compatibility of the materials of your pump with the liquid you want to pump. If you are uncertain regard-
ing chemical compatibility, contact your dealer for applications assistance and request a copy of our Corrosion Resistance
Charges. Do not use a pump that is not chemically compatible with the liquid you intend to pump or serious bodily injury,
death, fi re, explosion, or environmental damage could result.
ALSO, PLEASE READ SECTION I, II AND III BEFORE OPERATING PUMP.
I.
Safety Precautions ..................................................................................................................................... 2
II.
Preparing the Pump for Operation ........................................................................................................... 3
III.
Pump Operating Instructions.................................................................................................................... 4
2", Electric Drive Flexible (Long) Coupled
1½" / " Pneumatic Drive Close-Coupled
OPERATOR'S MANUAL & PARTS LIST
for End-Suction Centrifugal Pumps
(Non-Self Priming)
pumps have model numbers beginning with PCE and price codes beginning with 60-1.
pumps have model numbers beginning with PCP and price codes beginning with 60-.
pumps have model numbers beginning with PCR and price codes beginning with 60-3.
pumps have model numbers beginning with PCN and price codes beginning with 60-4.
SAFETY WARNING
'PC' PUMPS
3" Cast Iron Pedestal Mount
1½"/" Engine Drive Close-Coupled
1
2", Hydraulic Drive Close-Coupled
1½" / " Electric Drive, Close-Coupled
OPERATION AND
SERVICE GUIDE
PO-1775F
JAN. 01
Advertisement
Table of Contents
Related Manuals for ASM Pacer Pumps PC Series
Summary of Contents for ASM Pacer Pumps PC Series
- Page 1 ‘PC’ PUMPS PO-1775F OPERATION AND SERVICE GUIDE PO-1775F OPERATOR’S MANUAL & PARTS LIST JAN. 01 for End-Suction Centrifugal Pumps (Non-Self Priming) Before reading or using this manual be certain of the material of construction of your pump. Check the model number label on the pump as follows: POLYESTER pumps have model numbers beginning with PCE and price codes beginning with 60-1.
-
Page 2: Table Of Contents
PO-1775F OPERATOR’S MANUAL FOR: END-SUCTION CENTRIFUGAL PUMPS Table of Contents PLEASE READ SECTIONS I, II AND III BEFORE OPERATING PUMP. Page no. Safety Precautions ............................. 2 Preparing the Pump for Operation ......................3 III. Pump Operating Instructions........................4 Pump Trouble Shooting and Repair ......................4 Pump Disassembly and Repair ........................ -
Page 3: Preparing The Pump For Operation
PO-1775F 15. Do not tighten inlet and discharge fittings more than one it is necessary to fill the suction line and the pump (referred to turn beyond hand tight. Excessive force will damage the as the system) before starting the pump. A non-self-priming pump or fittings. Use teflon sealing tape on all threaded centrifugal pump can only pump if the system is full of liquid fittings. and the pump encounters no air. It is not necessary to drain the 16. -
Page 4: Pump Operating Instructions
III. PUMP OPERATING INSTRUCTIONS PO-1775F 1. Fill the system with liquid before starting. Do not run the pump dry; damage to the mechanical shaft seal may result. There are FIGURE 1 no points on the pump which need lubrication. The mechani- cal shaft seal is self lubricating, and designed to handle clean liquids. - Page 5 PO-1775F 1. When installing a new seal, always replace both elements (items Rotate the shaft while listening for scraping noise. If scraping is 13 & 14) and install the o-ring (item 11) around the bracket half heard, remove the volute and impeller and remove one washer of the seal (item 13). Do not bear directly on the seal surface type shim.
-
Page 6: Baseplate Kits
PO-1775F 90° ANGLE 8. To avoid angular misalignment, insert a measuring device (taper gauge or feeler gauge) between the coupling faces at four locations 90° apart (See arrows in Figure 6) and measure the gap at each of the four locations. For proper alignment all four measurements should be equal. - Page 7 PO-1775F OF CENTRAL DISCHARGE PORT - SEE NOTE 1 Pump mounted to molded bearing housing and flexible coupled to motor OF CENTRAL SUCTION PORT - SEE NOTE 1 NOTE: 1) THE SUCTION AND DISCHARGE PORT OF THE 1½”-2” PUMP FEATURE 1½” NPT PUMP FEET OR BSP FEMALE THREADS (INTERIOR) SLOT AND 2” NPT OR BSP MALE THREADS PLASTIC PEDESTAL (EXTERIOR). THE SUCTION AND DIS- FEET SLOT CHARGE PORTS OF THE 3” PUMP FEA- TURE 3” NPT OR BSP MALE THREADS (EXTERIOR ) ONLY.
-
Page 8: Pump Parts List And Parts Diagram
VII. ‘PC’ PUMP PARTS LIST PO-1775F ITEM # PART # PART DESCRIPTION QTY./PUMP 4 ....58-071 10F ..FLANGE NUT, Body, Stainless Steel, 1/4-20 Hex, for Polypropylene pumps only ............6 ....58-071 10 ..NUT, Body, Stainless Steel, 1/4”-20 Hex .......................... 6 6 ....58-1016 0 ..BRACKET, NORYL, gray ..............................1 ....58-1016 30 ..BRACKET, Polyester, black .............................. 1 ....58-1016 40 .. - Page 9 PO-1775F ITEM # PART # PART DESCRIPTION ....58-1009 71 ..O-RING, Drain Plug, BUNA-N ............................1 ....58-1009 7 ..O-RING, Drain Plug, EPDM .............................. 1 ....58-1009 73 ..O-RING, Drain Plug, Viton ..............................1 3 ....58-073 0 ..PLUG, Drain, NORYL, gray .............................. 1 ....58-073 30 ..
- Page 10 (and reship to the Buyer with transportation charges collect to anyplace in the U.S.) of defective goods provided that if the company is unable to correct a defective component part or product, the Buyer shall be entitled to elect a credit at the original buyer’s purchase price. To return a PACER PUMPS ® NOTE: All specifications, as shown, are subject to change without notice. serving Div. of ASM Industries, Inc. industry 41 Industrial Circle 717-656-161 worldwide Lancaster, PA 17601 800-33-3861 Email:sales@pacerpumps.com FAX: 717-656-0477 Part No.
- Page 11 PO-1775F ‘PC’ PUMP EXPLODED VIEW PARTS DIAGRAM Figure 7 44 43...
Need help?
Do you have a question about the Pacer Pumps PC Series and is the answer not in the manual?
Questions and answers