1. Manuals
  2. Brands
  3. OmniCell Manuals
  4. Music Mixer
  5. 1-Cell CTPC
  6. Installation and service manual

OmniCell 1-Cell CTPC Installation And Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
1-, 2-, 3-Cell CTPC
Console Installation and
Service Guide
67-2014 Rev G
Includes G4 Upgrade, Install and
Service Guides

Advertisement

Table of Contents
loading

Summary of Contents for OmniCell 1-Cell CTPC

  • Page 1 1-, 2-, 3-Cell CTPC Console Installation and Includes G4 Upgrade, Install and Service Guides Service Guide 67-2014 Rev G...
  • Page 2 This guide and accompanying software and/or hardware described in it are protected under copyright laws and may not be copied, wholly or in part, without the express written consent of Omnicell, Inc. The same proprietary and copyright notices must be attached to any permitted copies as were attached to the original documents.

  • Page 3: Table Of Contents

    Tools List ..............2-1 © 2011 Omnicell, Inc.
  • Page 4 Labeling ..............7-4 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 5 Color Coding ............11-6 © 2011 Omnicell, Inc.
  • Page 6 Replace the Battery ............14-11 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 7 ............Feedback-1 © 2011 Omnicell, Inc.
  • Page 8 Table of Contents 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 9: Ct Pc Box Parts

    The following tools are required to install the CT PC Box:  T8 Torx Driver  T10 Torx Driver  T15 Torx Driver  9/64” Allen wrench © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 10: Keyboard Door Bezel

    6. Remove the four 4-40 x 3/8 buttonhead screws that secure the rear keyboard door. Figure 1-3. Remove the four screws securing the rear keyboard door 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 11: Replacement Procedure

    Ensure that the cables are lying flat within the plastic sheath and then replace the keyboard cable cover into the slots on the back of the enclosure. 5. Replace the two 4-40 x 3/8 SHC screws. 6. Close the keyboard door. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 12: Keyboard

    Figure 1-5. Remove the six screws that secure the keyboard bracket 4. Remove the bracket. Figure 1-6. Remove the keyboard bracket 5. Remove the keyboard. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 13: Replacement Procedure

    1-3. 7. Plug in the cabinet power cable. 8. Power up the cabinet and check the speaker to ensure that it is working. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 14: Lcd Bezel Assembly

    7. Disconnect the following cables from inside the CT PC Box:  Inverter cable from J3  24-pin keyboard harness assembly from the numeric keypad  LCD data cable  Touch screen data cable 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 15 Figure 1-9. Disconnect the LCD data cable and inverter cable Figure 1-10. Disconnect the 24-pin keyboard harness assembly Figure 1-11. Disconnect the touch screen data cable © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 16 10. Slide the LCD bezel assembly to the left; remove the standoffs from the keyholes and pull the LCD bezel away from the frame. Figure 1-13. Remove the LCD bezel assembly from the CT PC Box 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 17: Replacement Procedure

    1. Attach the LCD data cable to the rear of the bezel assembly and to J1 on the motherboard. 2. Replace the LCD bezel assembly onto the frame. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 18: Lcd Display And Touch Screen Glass

    Figure 1-15. Remove the five SHC screws 5. Remove the 4-40 x 1/4 flathead screw in the lower right corner. Figure 1-16. Remove the flathead screw in the lower right corner 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 19 Do not touch the inner surface of the touch screen glass as this could prevent the touch screen from working properly when re-installed. Carefully pick up the touch screen glass by the sides when moving it. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 20: Replacement Procedure

    2. Remove the LCD Bezel Assembly. See “Removal Procedure” on page 1-6. 3. Remove the LCD display and touch screen glass. See “Removal Procedure” on page 1-10. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 21 Figure 1-19. Remove the flex cable 5. Remove the four 4-40 x 1/4 SHC screws to remove the keyboard bracket from the bezel. Figure 1-20. Remove the four screws © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 22: Replacement Procedure

    7. Replace the five 4-40 x 1/4 SHC screws from the rear of the assembly to secure the LCD bracket to the LCD bezel assembly. 8. Replace the LCD bezel. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 23: Touch Pad

    4. Replace the touch screen glass and LCD display. See “Replacement Procedure” on page 1-12. 5. Replace the LCD bezel assembly. See “Replacement Procedure” on page 1-9. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 24: Color Touch Pc Box

    The CT PC Box is heavy. Trying to lift or remove the box alone could result in injury. Use a second person to help lift and remove the CT PC Box from the OmniSupplier cabinet. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 25: Installation Preparation

    1. Unlock the PowerCom3 CT PC Box top cover with the cam lock key #2036. 2. Lift the front cover and slide it forward to remove. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 26: Installation Procedure

    1. Open the PC box. 2. Change dip switches 1 and 2 on the power/communication board to On. 3. Close the PC box. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 27 AC outlet. Note: If power problems continue to occur, these cabinets should be placed on an external UPS unit. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 28 1-20 CT PC Box Parts Auto Power Reset 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 29: Frames And Wireways

    2. Unplug the cabinet power cord from the outlet. 3. Unlock the cabinet doors using the #2036 key. 4. Remove the screws that secures the CT PC Box to the cabinet. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 30 Torx driver. [8-32x3/8 SHC screws] Figure 2-2. Supply cabinet a. Slowly pull the CT PC Box from the frame until the side-mounted slides lock and stop. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 31 Remove the cover by lifting the front end and pulling away from the cabinet. d. Disconnect the SPC cables from the PowerCom board. Figure 2-4. Disconnect the SPC Cables © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 32 The following sections cover optional equipment that may be present on any given cabinet that must be removed to access the wireway cables. A pharmacist must be present when servicing drawers with medications. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 33: 9-Drawer Carrier

    3. Remove the two screws securing each controller cable cover using a T10 Torx screwdriver. Figure 2-7. Remove the screws securing the controller cable cover © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 34 11. Remove the three wireway cables located on the inner side of the slide support brackets. The cables are located underneath drawers #2, 7 and 9. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 35: Omnidispenser

    2. Remove the two screws securing the rail cable bracket. Figure 2-11. Remove the two screws securing the rail cable bracket © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 36 4. Remove the rail cable bracket. 5. Disconnect the rail cable from P1 on the rail controller board. Figure 2-13. Disconnect the cable from P1 on the rail controller board 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 37: Ribbon Cable

    1. Remove the four screws, two on each side, that secure the top tray to the frame. Figure 2-15. Remove the four screws securing the top tray to the frame. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 38 3. Disconnect the ribbon cable from the reach board and pull the ribbon cable through the opening on the right side of the tray. Figure 2-17. Remove the ribbon cable from the slot on the right side of the tray. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 39 7. Place one screw back in the top bayonet to secure the bayonet to the frame. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 40 Figure 2-20. Remove the two screws securing the second bayonet from the top to the frame 9. Remove the second bayonet from the frame and disconnect the ribbon cable. Figure 2-21. Remove the second bayonet and disconnect the ribbon cable 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 41: Restock Door

    Figure 2-22. Remove the screws securing the trunnion bars to the module frame 2. Remove the three screws securing the fix inhibitor bracket. Figure 2-23. Remove the three screws securing the fix inhibitor bracket © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 42: Bottom Bayonet

    4. Remove the door. Bottom Bayonet 1. Remove the four screws that secure the bottom bayonet to the frame. Figure 2-25. Remove the bottom bayonet screws 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 43: 3-Drawer Carrier

    3. Disconnect the ribbon cables from the wireway. Figure 2-27. Disconnect the ribbon cables from the wireway 3-drawer Carrier The removal procedure for the 3-drawer carrier is similar to the 9-drawer carrier. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 44: Wireway

    Figure 2-28. Remove the Screws Securing the Wireway 2. Pull the wireway slightly forward and disconnect the overhead communications cable. Figure 2-29. Disconnect the Overhead Communications Cable 3. Remove the wireway. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 45: Shelves

    Figure 3-1. Lift the Shelf Clips 2. Disconnect the switchpanel from the SPC board in the wireway. Figure 3-2. Disconnect the Switchpanel from the SPC Board © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 46 If a new shelf will not be re-installed in the location, be sure to cover the opening in the frame with a cover. The cover is mostly aesthetic, but will prevent loose objects from falling into the wireway. 6. Remove the dividers from the clips. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 47: Installation Procedure

    2. Insert a shelf clip into the hole on the frame. 3. Slide the switchpanel into its holder. Figure 3-6. Slide the switchpanel into its holder 4. Lift up the tabs on the shelf clips. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 48 8. Lower the shelf into the shelf supports and ensure they are locked into place. 9. Place the clips on the shelf at the required position. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 49: Pull-Out Shelf

    5. Insert mounting screws, one on each side, using a Torx T15 screwdriver. 6. Connect the switchpanel cable to the wireway. 7. Replace the connector covers. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 50 3-6 Shelves Pull-out Shelf 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 51: Switchpanels

    Switchpanels Introduction Switchpanels are located in four places on Omnicell units: on a shelf, in a supply drawer or pull- out shelf, on a suture rack and on a catheter rack. The switchpanels, commonly referred to as button bars, are used to aid in the identification of specific items in a dispenser unit. When a user selects an item from the dispenser unit, the LEDs on the switchpanel light up and indicate the location of the product.

  • Page 52: Removal Procedure

    3. Remove the switchpanel and its holder from the clips. 4. Slide the switchpanel from its holder. Figure 4-2. Remove the switchpanel from its holder 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 53: From A Supply Drawer

    If the supply drawer is to be located directly above a pharmacy drawer, it is recommended that the screws be re-installed from above of the bracket. 3. Remove the supply drawer and its casing from the dispenser unit. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 54: From A Pull-Out Shelf

    4. Remove the two screws using a small Phillips head screwdriver. 5. Remove the switchpanel cable from the wireway cable. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 55: From A Suture Rack

    Figure 4-7. Remove the screws securing the suture rack to the housing. 3. Remove the suture rack from the L-brackets. 4. Open the suture rack and locate the cable. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 56 Figure 4-9. Remove the LED cable from the plastic routing clip 7. Remove the cable plate from the rear of the housing. Figure 4-10. Disconnect the cable plate from the suture rack drawer 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 57: From A Catheter Rack

    From a Catheter Rack 1. Pull the cath rack rail forward until it is fully extended. Figure 4-12. Extend the cath rack rail until it locks into place © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 58 2. Remove the two nuts on either side of the front panel using a 5/16” nut driver. Figure 4-13. Remove the nuts securing the LED panel 3. Disconnect the LED cable from the panel. Figure 4-14. Disconnect the LED cable 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 59 Figure 4-15. Remove the two screws on the front plate handle 5. Remove the front plate. Figure 4-16. Remove the front plate © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 60 Stop when the switchpanel is about halfway out. 8. Disconnect the switchpanel cable from the switchpanel. Figure 4-18. Disconnect the switchpanel cable 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 61 Switchpanels 4-11 Removal Procedure 9. Slide the switchpanel forward and remove it from the rail. Figure 4-19. Remove the switchpanel from the Catheter rack rail. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 62 4-12 Switchpanels Removal Procedure 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 63: Doors

    Doors 5-1 Introduction Doors Introduction Omnicell 1-,2-, and 3-cell cabinets and half-cell units have doors that are similar, but can be different sizes. The standard sizes for a door on a 1-, 2-, or 3-cell cabinet are: (A) full height, 2/3 height (next page), (B) 1/3 height and (C) CT PC Door.

  • Page 64: Tools List

    Torx T20 screwdriver. Note: Hold onto the door while removing the two screws. The door may fall away from the cabinet after the screws are removed. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 65: Installation Procedure

    2. Place the top bracket onto the door and line up the top of the door with the screw holes on the cabinet frame. 3. Attach the two screws securing the top bracket. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 66 5-4 Doors Installation Procedure 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 67: Locks And Latches

    The following tools are required to install the CT PC Box:  Torx T8 driver  Torx T10 driver  Torx T15 driver  9/64” Allen wrench  Cam lock key #2036 © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 68: Removal Procedure

    1. Unlock and remove the manual override cover. Figure 6-2. Unlock and Remove the Manual Override Cover 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 69 Figure 6-3. Three Drawer Manual Override Cover and Locks 3. Remove the pawl latch. 4. Loosen and remove the larger nut that secures the lock to the cover. 5. Remove the lock. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 70 6-4 Locks and Latches Removal Procedure 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 71: Drawers

    The Omnicell Sensing Lid (OSL) models have sensing lids. As each lid is lifted, the system senses and records access to the bin. This guarantees security to those drawers that contain controlled substances.

  • Page 72: Bin Configuration

    4. Use the gray circular labels provided with the kit to cover any un-used divider slots in the bin liner. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 73: Lit Matrix Drawers

    Be sure to place a light pipe into every notch, even if the position will not be used for guiding light purposes. The pipes provide support and help keep the dividers in place. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 74: Labeling

    Once a bin has been configured, label the bin divider to correspond with the bin name corner. and affix the label to the top of the right rear divider of that bin. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 75: Installation Procedures

    3. Insert the right/left bin divider into the bin liner. 4. Insert the front/rear bin divider into the bin liner. 5. Connect the drawer cable, then insert the drawer into the carrier. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 76: Pharmacy Drawer

    7. Line up the tape to the edges of the clamp and secure the clamp to the carrier with two screws. using a Torx T15 screwdriver to tighten the screws. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 77 17. Close the drawer and replace the pharmacy manual override cover. 18. Power up the cabinet. 19. Program the drawer at the OmniSupplier in OmniConfigurations. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 78: Three-Drawer Pharmacy Module

    Pharmacy Module needs to be installed. 5. Remove the black rubber door bumper on the frame of the unit where the carrier will be installed. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 79 Secure the panel to the frame with rivets using a rivet installer. Figure 7-8. Slide the plastic cover panel between the metal flange and the acrylic panel © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 80 9. Secure the right carrier bracket to the frame with two screws with a Torx T15 screwdriver. Figure 7-10. Secure the carrier wall to the frame 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 81 11. Secure the left carrier wall to the frame with two screws using a Torx T15 screwdriver. Figure 7-12. Secure the left carrier wall to the frame © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 82 Torx T10 screwdriver. Figure 7-14. Install the front facia bracket 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 83 Figure 7-15. Connect the SPC-to-carrier cable. 15. Insert the tabs on the slide support brackets into the slots on the rear carrier wall. Figure 7-16. Insert the slide support brackets © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 84: Configuration

    5. Change the value of the zone to 6. Select Zone Access Configurations. 7. Change the value of the zone to 8. Select Pharmacy Options. 9. Change Support Pharmacy System to 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 85: Removal Procedure

    2. Remove the manual override cover on the pharmacy drawers. Figure 7-18. Remove the manual override cover 3. Pull the manual override lever/flag and open the desired pharmacy drawer. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 86 Torx T10 screwdriver. Figure 7-19. Remove the controller cable cover 5. Remove the cable clamp and disconnect the cable. Figure 7-20. Remove the controller cable 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 87: Resetting Drawer Addresses

    To check the current programming, or to reprogram the drawers: 1. Log on to the cabinet as omnitech 2. Select Omni Config > Program Pharmacy Drawers. 3. Select the zone from the menu. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 88 A message indicates when the drawer is successfully programmed. 5. Press Next Drawer and continue programming each drawer and zone until complete. 6. When finished, press Done. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 89: Drawer Connect Board

    2. Remove the manual override cover on the pharmacy drawers. Figure 8-1. Remove the Manual Override Cover 3. Remove all of the drawers in the pharmacy carrier. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 90 5. Remove the two screws securing the manual override lever, then remove the bar. Figure 8-3. Remove the Manual Override Bar 6. Remove the two screws securing the slide support bracket. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 91 8. Remove the two screws on either side of each cable mounting bracket using a Torx T15 screwdriver. Figure 8-5. Remove the Screws on the Cable Mounting Bracket © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 92 Figure 8-6. Disconnect the Drawer Cable from the Drawer Connect Board 10. Remove the SPC to drawer connect board cables. Figure 8-7. Remove the SPC to Drawer Connect Board Cables 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 93 1/16” Allen wrench. Figure 8-8. Remove the Screws Securing the Drawer Connect Board to the Wall 12. Remove the drawer connect board. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 94 8-6 Drawer Connect Board Removal Procedure 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 95: Manual Override

    Manual Override Introduction In the event of a hospital electrical power failure or an extended power outage, all Omnicell cabinets can be opened with a manual override mechanism. A series of locks, levers and linkages provide access to the supply doors, pharmacy drawers and pharmacy drawer bins.
  • Page 96 5. Remove the two screws securing the manual override lever, then remove the bar. Figure 9-3. Remove the Manual Override Bar 6. Remove the two screws securing the slide support bracket and slide support bracket. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 97 8. Remove the screws securing the top cover to the frame, one on each side of the carrier. Figure 9-5. Remove the screws securing the top cover to the frame 9. Remove the top cover. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 98 11. Remove the buttonhead screw securing the left carrier wall to the left side of the frame. Figure 9-7. Remove the buttonhead screw securing the left carrier wall to the left side of the frame 12. Remove the left carrier wall. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 99 Figure 9-8. Remove the four screws securing the right carrier wall to the right side of the frame 14. Remove the right and rear carrier walls together. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 100 Figure 9-10. Remove the buttonhead screw securing the manual override to the carrier wall 17. Slide the manual override away from the rear of the frame and remove the manual override. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 101: Catheter Rack

    7. Insert two Allen wrenches into the screw holes on the right and left sides of the frame to temporarily support the cath rack in place. Note: Keep a hand on the cath rack at all times to keep it from moving. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 102: Configuration

    7. Lift the cath rack off the Allen wrenches and carefully remove it from the frame. 8. Set the cath rack down with the hooks facing up so that they are not damaged. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 103: Service Procedures

    2. Remove the front LED panel by removing the two nuts on either side of the panel using a 5/16” nut driver. Figure 10-2. Remove the nuts securing the LED panel © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 104: Front Plate

    1. Perform the procedures described in “LED Panel” on page 10-3. 2. Remove the two screws on the plate handle. Figure 10-4. Remove the two screws on the plate handle 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 105: Switchpanel And Cable

    Figure 10-6. Remove the two screws securing the LED cable to the cath rack 4. Slide the switchpanel toward the back of the unit and stop when the switchpanel is about halfway out. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 106: Led Cable

    2. Remove the front LED panel by removing the two nuts on either side of the panel using a 5/16” nut driver. 3. Remove the front plate from the cath rack arm by removing the two screws using a Torx T15 screwdriver. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 107 4. Remove the two screws securing the plate on the back of the cath rack arm using a Torx T8 screwdriver. 5. Remove the plate. 6. Slide the switchpanel toward the back of the cabinet. 7. Disconnect the switchpanel cable from the switchpanel. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 108: Hooks

    3. Disconnect the two 50-pin cables from the SPC board. 4. Slide all the rails forward. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 109 Catheter Rack 10-9 Service Procedures 5. Remove the SPC cables from the housing and out through the three cable tags. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 110 10-10 Catheter Rack Service Procedures 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 111: Suture Rack

    3. Set the dip switches according to zone and shelf location. See the following table. Table 11-1. Dip Switch Settings for Cabinet Zones Switch Zone © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 112 11-2 Suture Rack Installation Procedure Table 11-1. Dip Switch Settings for Cabinet Zones Switch Zone 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 113 Suture Rack 11-3 Installation Procedure Table 11-1. Dip Switch Settings for Cabinet Zones Switch Zone © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 114 11-4 Suture Rack Installation Procedure Table 11-1. Dip Switch Settings for Cabinet Zones Switch Zone 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 115: Dividers

    The dividers can be full-height or half-height. A typical full-height divider looks like this: © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 116: Color Coding

    4. Place the color coding into the slot. 5. Replace the front panel. 6. Replace the two nuts and tighten them with the 5/16” nut driver. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 117: Removal Procedure

    4. Disconnect the switchpanel cable from the switchpanel. 5. Remove the switchpanel from the rack housing. 6. Flip the switchpanel over and disconnect the LED cable. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 118: Spc Board And Cable

    2. Remove the two screws securing the rack to the housing using a 3/32” Allen wrench or a T15 Torx screwdriver. Figure 11-2. Remove the screws securing the suture rack to the housing. 3. Remove the suture rack from the housing. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 119 11. Remove the cable, sliding it under the two attached brackets. 12. Disconnect the switchpanel cable from the connector on the back of the re-direction board. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 120 11-10 Suture Rack Removal Procedure 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 121: Installing A G4 Console

    Pharmacy cabinets PC box screws are accessed by opening the keyboard door and using the T15 Torx driver. [6-32x1/4 BH screws] Figure 12-1. Pharmacy cabinet © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 122 Figure 12-3. Unlock the CTPC Box Cover c. Remove the cover by lifting the front end and pulling away from the cabinet. d. Disconnect the SPC cables from the PowerCom board. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 123 A pharmacist must be present when servicing drawers with medications. g. Remove the wireway clip and disconnect the SPC cables from the wireway. Remove and discard the cables, but keep the wireway clip. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 124: Prepare For Installation Of The G4 Console

    Figure 12-6. Remove the innermost screw on the door hinge 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 125 2. Ensure that the tab of the small cover is positioned below the rear and side flange of the frame. Figure 12-8. Ensure the tab is below the rear and side flange © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 126 4. Place the larger cover on the left side of the console enclosure and set it on the ridge. Figure 12-10. Place the large cover into the frame opening 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 127 6. Attach the two sections of the cover by adding two screws to the top front portion of the cover. Use a Torx T15 driver. Figure 12-12. Add a screw to join the two portions of the cover © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 128 There is also a spare screw in the upgrade kit. Figure 12-13. Secure the large portion of the cover by replacing the screw 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 129 Do not tighten any of the screws until all of the screws are installed. Figure 12-14. Add three more screws to secure the lid pieces © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 130: Add The Ribbon Cable

    Add the Ribbon Cable 1. Add the new ribbon cable, plugging in both connectors to the wireway. Figure 12-15. Place the ribbon cables into the wireway 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 131 The cable clip secures the connectors, not the cable itself. Ensure that the cable is not caught underneath the clip when the clip is installed or the cable may become damaged. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 132: Connect The E-Box Battery

    Connect the E-Box Battery 1. Remove the two screws that secure the lid on the E-Box. Figure 12-18. Remove the two screws that secure the E-Box lid 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 133 Figure 12-19. Tighten the velcro straps around the battery 4. Connect the battery cable to the PowerCom4 board. Figure 12-20. Connect the battery to the PowerCom4 board © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 134: Install The G4 Console

    7-15 and “Installation Procedures” on page 7-5. 2. Pull the console back out until the rails stop. 3. Connect the wireway cable to the E-Box. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 135 Figure 12-22. Connect the wireway cable to the E-Box 5. Attach the network cable to the LAN port provided Figure 12-23. Attach the network cable © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 136: Close The G4 Console And Power On The Cabinet

    Figure 12-24. Remove the filter access panel 4. If the filter is not in place, install the filter. Slide the filter behind the filter holders. Figure 12-25. Add the filter 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 137 6. Lock the G4 console into place using the #2378 key. Turn the key vertical to lock the console into place. Figure 12-27. Power on the cabinet 7. Replace the filter access panel. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 138 12-18 Installing a G4 Console Install the G4 Console 8. Power on the cabinet. 9. Close the keyboard door. 10. Configure the cabinet as needed. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 139: G4 Pc Box Service

    If two people are not present to lift the CT PC console with E-Box into the frame, remove the E- Box from the console before lifting the console into the cabinet frame. Otherwise, proceed to the next section. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 140 Figure 13-3. Disconnect the power cables 3. Remove all the cables from the left-hand side of the E-Box frame, including all USB, sound, video and network cables. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 141 Figure 13-4. 4. Loosen but do not remove the screw on the side of the console frame. Figure 13-5. Loosen the screw © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 142 6. Push down on the two side clips that secure the PC Box frame to the console and pull the frame from the console. Figure 13-7. Remove the frame from the console 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 143: Install The E-Box Onto The Console

    Figure 13-8. 2. Straighten out the E-Box and slide it into place on the CT PC console frame. Figure 13-9. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 144 13-6 G4 PC Box Service 3. Replace and tighten the screws that secure the E-Box to the console frame. Figure 13-10. Figure 13-11. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 145 5. Reconnect the USB, power, sound and network cables on the left-hand side of the E-Box. refer Figure 13-13 to ensure that the cables are routed in the proper locations. Figure 13-13. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 146: Prepare Pc Box Console With E-Box

    Add Knock-out Safety Plate 1. If the safety plate on the back of the console has not been installed, add it before completing the rest of the install. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 147 3. If the security plate on the right rear of the console is not attached, place the plate onto the console and secure it with the screws provided. Use a Torx T-10 driver. Attach the network cable . Figure 13-16. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 148: Add The Flex Lock Or External Return Bin (Optional)

    1. Feed the extender cable up through the opening in the right rear of the CT PC console. Figure 13-17. 2. Connect the extender cable to the E-Box. Figure 13-18. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 149 4. Attach a strain relief to the cable. Place the strain relief six to nine inches from the connector. Figure 13-19. 5. Snap the strain relief into place and ensure that it is secure on the cable. Figure 13-20. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 150 7. Connect the Flex Lock or ERB cable to the extender. Figure 13-22. 8. Mount the Flex Lock or ERB according to the facility request. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 151: Remove And Replace The Lcd Touch Screen

    4. Remove the screw from the top surface of the access area. Figure 13-24. This screw must be removed before moving the CT PC box © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 152 6. Pull the system out enough to gain easy access to the rear of the LCD touch screen panel. Figure 13-26. Pull the PC Box only far enough to gain sufficient access 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 153 8. Remove the two TORX screws from the left rear of the LCD panel (to the right when viewed for the angle required to access). Figure 13-28. Remove the screws that secure the LCD touch screen panel assembly © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 154 Figure 13-29. Carefully disengage the panel from the keyhole fasteners Figure 13-30. Showing the male half of the keyhole fastener, located on the rear of the LCD touch screen assembly, shown after removal 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 155: Lcd Touch Screen Replacement

    Note that the lowest socket on the LCD panel receives the power lead with a flat edge in the connector body. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 156: Remove And Replace The Keyboard And Printer Panel

    2. Unlatch the printer panel via the latch at the top of the panel, and carefully rotate the panel forward. It will rest safely in the lowered position. Figure 13-32. Unlatch the keyboard panel... Figure 13-33..and carefully lower it forward 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 157 3. Remove the rear panels of both printers, use a thumb to push the latch forward. Figure 13-34. Removing rear printer panel. Note position of thumb on latch Figure 13-35. Detail of latch to release rear printer panel © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 158 Figure 13-36. Remove the four screws from the rear of the right printer 5. Rotate the right printer forward to gain access to the connections on the rear. Figure 13-37. Gaining access to the right printer connections 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 159 10. Rotate the panel forward to gain access to the connections in a similar fashion as just used to access the right printer connections. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 160 Figure 13-40. Removing the Mini USB cable for the left printer 12. Remove the data cable from the chassis circuit board, not the printer board Figure 13-41. Removing the data cable for the left printer 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 161 14. Remove the main power cable from the keyboard chassis circuit board. Figure 13-43. The main power lead is the largest cable of the cable-bundle © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 162 16. Remove the mini USB cable from the keyboard chassis circuit board. Figure 13-45. Removing the Mini USB lead from the main circuit board in the chassis 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 163 Figure 13-46. The circle highlights the location of the speaker connection 18. Cut the cable tie securing the power/data/USB cable bundle. Figure 13-47. Removing the strain-relief zip-tie © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 164 The keyboard chassis should remain caught on the hinge pins, but exercise caution. Figure 13-48. Removing fastener on the right Figure 13-49. Removing the fastener in the center 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 165: Keyboard And Printer Panel Removal

    Replacement of the Keyboard and Printer Panel is the reverse of removal. Close the CT PC Console and Power on the Cabinet 1. Carefully slide the CT PC console with E-Box into the cabinet. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 166 3. Lock the CT PC console into place using the key provided. Turn the key vertical to lock the E- Box into place. Figure 13-52. 4. Power on the unit. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 167 G4 PC Box Service 13-29 Remove and Replace the Keyboard and Printer Panel 5. Configure the unit as needed. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 168 13-30 G4 PC Box Service Remove and Replace the Keyboard and Printer Panel 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 169: E-Box Service Guide

    Figure 14-1. Remove the screws that secure the E-Box lid 2. Using the finger holds in the lid, pull the lid forward and lift it to remove it from the frame. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 170 14-2 E-Box Service Guide Open the E-Box 3. Set the lid and the three screws aside. Figure 14-2. The CTPC console E-Box with the lid removed 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 171: Remove/Replace The Hard Drive

    Remove the Hard Drive 1. Remove the data and power cables from the hard drive. Figure 14-3. Disconnect the data and power cables from the hard drive © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 172 3. Lift the hard drive up, pull it away from the drive all, and remove it from the E-Box. Figure 14-5. Remove the hard drive 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 173: Replace The Hard Drive

    2. Tighten the screw that connects the hard drive plate to the E-Box wall. Figure 14-7. Tighten the screw that secures the hard drive to the E-Box wall © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 174 Remove/Replace the Hard Drive 3. Replace the data and power cables to the hard drive. Figure 14-8. Connect the data and power cables for the hard drive 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 175: Remove/Replace The Fans

    Remove the Fans 1. Remove the four screws that secure each cooling fan to the E-Box. Figure 14-9. Remove the screws securing the fans to the E-Box © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 176: Replace The Fans

    Figure 14-10. Disconnect the fan cables from the PowerCom4 board 3. Remove the fans from the E-Box. Replace the Fans 1. Hold each fan in place inside the E-Box. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 177 Figure 14-11. Replace the screws securing the fans to the E-Box 3. Connect the fan cables to the PowerCom4 board. Figure 14-12. Connect the fan cables to the PowerCom4 board © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 178: Remove/Replace The Battery

    2. Disconnect the cable that connects the battery to the PowerCom4 board. Figure 14-14. Disconnect the cable that connects the battery to the PowerCom4 board 3. Remove the battery from the E-Box. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 179: Replace The Battery

    Figure 14-15. Set the battery on the straps and secure the straps 3. Connect the cable that connects the battery to the PowerCom4 board. Figure 14-16. Connect the battery cable to the PowerCom4 board © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 180: Remove/Replace The Power Supply

    Remove the Power Supply 1. Disconnect the cable that connects the power supply to the PowerCom4 board. Figure 14-17. Disconnect the power supply cable from the PowerCom4 board. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 181 Figure 14-18. Remove the screw that secures the power supply to the E-Box 3. Pull the power supply away from the E-Box wall. 4. Lift, but do not remove, the power supply from the E-Box. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 182 5. Remove the power cable connected to the power supply. Figure 14-20. Disconnect the power cable from the power supply 6. Remove the power supply from the E-Box. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 183: Replace The Power Supply

    1. Place the power supply into the opening in the E-Box. Figure 14-21. Place the power supply 2. Reconnect the power cable to the power supply. Figure 14-22. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 184 4. Secure the power supply to the E-Box by replacing the screw that secures the power supply to the E-Box. Figure 14-24. Replace the screw that secures the power supply to the E-Box 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 185: Remove The Wireless Card

    1. Remove the screw that secures the wireless card to the E-Box frame. Figure 14-26. Remove the screw securing the wireless card to the E-Box © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 186: Replace The Wireless Card

    1. Place the wireless card into the E-Box, ensuring that it fits snugly into the slot on the motherboard. Figure 14-28. Replace the wireless card 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 187: Remove/Replace The Power Entry Module

    1. Remove the battery. Follow the steps in “Remove the Battery” on page 1-8. 2. Remove the power supply. Follow the steps in “Remove the Power Supply” on page 1-10. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 188: Replace The Power Entry Module

    1. Feed the cables through the back of the E-Box into the box. 2. Pinch the tabs on the corners of the power entry module and push the module from the rear into the box. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 189 4. Replace the power supply. Follow the steps in “Replace the Power Supply” on page 1-13. 5. Replace the battery. Follow the steps in “Replace the Battery” on page 1-9. © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 190 14-22 E-Box Service Guide Remove/Replace the Power Entry Module 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 191 14-7023 MFG,ASSY,2222,SD,DRAWER,RX2 14-7024 MFG,ASSY,3131,SD,DRAWER,RX2 14-7016 lit drawer MODEL,OLMD24,24-LIT,MATRIX,DRAWER Lit Matrix Drawers 15-7089 DRAWER,MATRIX,24 BIN LIT,OLMD24,NO LINER Table A-1. 1-, 2-, 3-cell cabinet service part list © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...

  • Page 192: A-2 Appendix A: Part List

    SPC Board and Cable 40-7031 PCB,ASSY,CARRIER,RX2 Drawer Connect Board Drawer Connect 40-3001 drawer connect board PCB,ASSY,DRAWER,CONTROLLER Board 40-7051 PCB,ASSY,CARRIER,3-DRAWER Table A-1. 1-, 2-, 3-cell cabinet service part list 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 193 Keyboard Door Bezel Three-Drawer 53-2061 upper bracket BRACKET,HINGE,UPPER,OMNI,2 Pharmacy Module 53-3031 suture rack housing HOUSING,DRAWER,SUTURE,RACK Suture Rack Housing Table A-1. 1-, 2-, 3-cell cabinet service part list © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 194 LCD Display and Touch Screen Glass 71-1163 LCD display DISPLAY,LCD,10.4”,NEC NL8060BC26-30D LCD Display and Touch Screen Glass Table A-1. 1-, 2-, 3-cell cabinet service part list 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.
  • Page 195 SCREW,BH,TORX,6-32,X,3/16,SS LCD Bezel Assembly 94-6138 6-32x1/4 BH screws SCREW,BH TORX,6-32X1/4,SS [Rx cabinet] CT PC Box Removal Table A-1. 1-, 2-, 3-cell cabinet service part list © 2011 Omnicell, Inc. 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G...
  • Page 196 Three drawer pharmacy module THREE DRAWER PHARMACY MODULE Three-Drawer Pharmacy Module OmniDispenser OSOMDT OmniDispenser OPTION KIT, OMNIDISPENSERTALL Table A-1. 1-, 2-, 3-cell cabinet service part list 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 197: Index

    LED cable 10-6 numeric keypad 1-12 LED panel 10-3 rail slide 10-8 removal 10-2 Omnicell Locking Lid (OLL) 7-1 switchpanel 10-5 Omnicell Matrix Drawer (OMD) 7-1 catheter rack module 10-1 Omnicell Sensing Lid (OSL) 7-1 Color Touch PC Box 1-1...
  • Page 198 1-1, 2-1, 4-1, 5-2, 6-1, 7-1, 8-1, 9-1, 10-1, 11-1 touch pad 1-15 touch screen glass 1-10 trunnion bars 2-13 wireway 2-1, 2-16, 6-2 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

  • Page 199: Feedback Form

    Feedback Form This document is designed to provide relevant technical information to those responsible for the implementation, service, and support of Omnicell products. The Documentation team needs your input, so we can continue to improve our publications. Please send us your feedback: Did this document meet your needs? If so, please let us know what we’re doing right.
  • Page 200 1-, 2-, 3-Cell Color Touch Installation and Service Guide/67-2014 Rev G © 2011 Omnicell, Inc.

This manual is also suitable for:

2-cell ctpc3-cell ctpc

Table of Contents